Advertisement
Product Parameters:
Product Name: Dehumidifier Product Model: DEM-DT16C
Rated voltage/frequency: 220V~50H2 Rated input current: 1.0A
Machine size: 328*197*508mm Water tank capacity: 2.L
Dehumidification capacity: 15L/24H (38℃ 90%RH)
Nominal dehumidification capacity: 020-0.25kg/h (27C-60%RH)
Executive standard: GB4706.1-2005GB470632-2012
GB4343.1-2009GB17625.1-2012
Product Features:
Powerful dehumidification ability
Based on the principle of freezing technology, this dehumidifier can remove
appropriate moisture from the air to keep the room dry and comfortable.
Cleverly portable design
It is simple and lightweight, and it is very convenient to move.
Low temperature work, automatic defrost
When 5℃<room temperature<12℃, the machine will stop for defrosting every 30
minutes. When 12 ℃ <room temperature<20 ℃ , the machine will stop every 45
minutes for defrosting.
Humidity adjustability
Different dehumidification levels can be selected according to different room needs.
Advertisement
Table of Contents
Summary of Contents for deerma DEM-DT16C
- Page 1 Product Parameters: Product Name: Dehumidifier Product Model: DEM-DT16C Rated voltage/frequency: 220V~50H2 Rated input current: 1.0A Machine size: 328*197*508mm Water tank capacity: 2.L Dehumidification capacity: 15L/24H (38℃ 90%RH) Nominal dehumidification capacity: 020-0.25kg/h (27C-60%RH) Executive standard: GB4706.1-2005GB470632-2012 GB4343.1-2009GB17625.1-2012 Product Features: Powerful dehumidification ability Based on the principle of freezing technology, this dehumidifier can remove appropriate moisture from the air to keep the room dry and comfortable.
-
Page 2: Quiet Operation
on off timer No machine switch time is set. Quiet operation Low-noise operation design. Energy-saving design Piezoelectric power consumption design. Safe use warning: When using this machine, please pay attention to the following safety notices: 1. When cleaning or storing this dehumidifier, please unplug it first. 2. - Page 3 Instructions: Color aperture Double 8 color word screen The display has a three-color aperture (red, blue, purple). After the machine is turned on, the aperture starts to light up. When the ambient humidity is above 70, it displays red; when the ambient temperature is below 50, it displays purple, and when the ambient humidity is...
- Page 4 Setting Wind speed Negative ion Timing Mode power supply Strong wind Low wind Negative ion Full of water Timing Dry clothes Dehumidification 1. At first power on, the buzzer beeps once, the machine is in standby, double 8 displays the ambient humidity for 3 seconds, and then turns off. 2.
-
Page 5: Water Tank
It is effective in dehumidification mode, and the humidity is set to 40% by default every time it is switched to dehumidification mode. Change the humidity setting value by pressing the Setting key, the humidity setting range is 40%-80% -40%, every 5% interval, when the humidity is set, double 8 flashes display, after stopping the key for 5 seconds, it returns to the normal display state. - Page 6 1. Hold the left and right sides of the water tank with your hands, and pull the water tank out. 2. Empty the water in the water tank. Notice: 1. Do not remove the float in the water tank. If the float in the water tank is removed, the full water sensor will not be able to sense the water level normally, so that it cannot be turned on normally.
-
Page 7: Maintenance
10mm) Insert the drain port on the back of the product, pass the small hole in the water tank gap, install the water tank in place, straighten the drain pipe, and then drain the water from the machine through the water pipe to achieve continuous drainage. Maintenance Dehumidifier cleaning Wipe the body with a soft, slightly damp cloth. -
Page 8: Filter Installation
3. Filter installation Insert the filter screen into the filter screen frame, and then first align the filter screen frame with the product rear shell card slot, and install the filter screen frame in place. Dehumidifier storage When you plan to store this product without using it for a long time, pay attention to the following steps: 1. -
Page 9: Troubleshooting
Spatial spacing When the dehumidifier is working, ensure that the minimum spacing around it is as shown in the figure below. Circuit diagram Troubleshooting... - Page 10 If the following conditions occur, please confirm the following conditions before requesting customer service: Failure Potential cause of failure solution Is the power cord properly Connect the plug to connected? the socket Does the full water indicator Drain the water in the Machine doesn't work flash? water tank and put it...
Need help?
Do you have a question about the DEM-DT16C and is the answer not in the manual?
Questions and answers