LOUP ELITE YIELD MONITOR • OPERATION MANUAL Service and Technical SupporT Contact: Loup Electronics Inc. Address: 3030 N. 40TH St. AfTER HOuRs/WEEkEND suppORT: Lincoln, NE 68504 402-318-6415 Phone: 877-489-LOUP(5687) 402-464-7131 402-853-6249 Fax: 402-464-7104 E-mail: info@loupelectronics.com TaBle oF conTenTS 1.0 sYsTEM OvERvIEW ....3 6.0 COMbINE sETup.
1.0 SySTem overview The Loup Elite Yield Monitor is a color touchscreen display designed to provide accurate Yield, % Moisture, and Mapping information for any model combine. This manual will familiarize you with operation, calibration and technical information. All aspects and features are detailed but may not be applicable to your specific system configuration.
LOUP ELITE YIELD MONITOR • OPERATION MANUAL 2.0 main Screen FuncTionS 2.5.1 REsETTINg DIspLAYs A select number of the displays can be reset to 0 while The following sections will familiarize yourself with the operation harvesting. To reset to 0, press and hold on the desired window of the main screen.
LOUP ELECTRONICS • 1-877-489-5687 • WWW.LOUPELECTRONICS.COM 2.11 CROp/vARIETY 3.1 ENTERINg A TAsk NAME Selecting the Crop Icon from the lower Begin a new task by first entering the right of the Main Screen will load the Crop task name you desire. Select the task...
LOUP ELITE YIELD MONITOR • OPERATION MANUAL an incrementing load counter with the calibration process 3.6 LOAD A pREvIOus TAsk done within the Loads Page. The following steps will guide you If you wish to resume a previously started through the calibration process for both of these options.
LOUP ELECTRONICS • 1-877-489-5687 • WWW.LOUPELECTRONICS.COM Nudge This & Active Load: 4.2 LOAD NuDgE (LOAD MANAgEMENT ON) Selecting this option When Load Management is On, the Yield Nudge is performed updates the total bushels through the Loads Page. Any load can be nudged individually or for the selected load and as the Yield Nudge factor can be also applied to the Active Load.
LOUP ELITE YIELD MONITOR • OPERATION MANUAL 5.0 crop deTailS 5.4 sECTIONs The number of sections defined for each crop Selecting the crop at the bottom right corner will be displayed on the main screen when of the Main Screen brings you to the Crop reducing the header cut width.
5.11 MOIsTuRE ON/Off 6.3.2 vARIAbLE HEIgHT sENsOR Using the moisture sensor is an optional feature of the Elite Yield Monitor. Toggle the sensor On or Off here if for example you are adding a moisture sensor at a later point.
LOUP ELITE YIELD MONITOR • OPERATION MANUAL 6.4.3 WHEEL puLsEs pER 400fT 7.4 gps sTATus This value directly affects the MPH reading Use this page to confirm communication to when a shaft sensor is used. Perform a Speed your GPS receiver. Information for current...
Note: While each point can be manually changed, its not to travel from the combine header up to the recommended to do so. Contact Loup Electronics for yield sensor location in the clean grain elevator. futher assistance.
LOUP ELITE YIELD MONITOR • OPERATION MANUAL ¾ Speed: The Elite console will display the ¾ speed you should 12.1 bRIgHTNEss achieve (based on the max speed reached on the first step). Use Use the Plus or Minus keys to increase or...
On a USB drive, create a folder titled “EliteUpdate” on the root level of the USB. Within this folder place the update file from Loup Electronics, this should appear as a .srec file format. Insert USB into the Elite console and select the “Update App”...