Page 1
Form No. MSC23901 Rev A Owner's Manual 48in Snowthrower Kit Snowrator MAG Part No. STX24410—Serial No. 400000000 and Up *MSC23901* Register at www.bossplow.com. Original Instructions (EN)
Page 2
(Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the The snowthrower is intended to be used on a BOSS recommended precautions. stand-on, multi-purpose machine. This attachment is used to remove snow from paved or gravel surfaces, such as driveways and sidewalks, and other surfaces for traffic on residential or commercial properties.
Contents Safety Safety ............... 3 Improper use or maintenance by the operator or Preparation............3 owner can result in injury. To reduce the potential Operation............3 for injury, comply with these safety instructions Safety and Instructional Decals ......4 and always pay attention to the safety-alert Setup ................
causes distractions; otherwise, injury or property damage may occur. • Do not operate the attachment near bystanders. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal139-8895 139-8895 1.
Setup Note: Ensure that the coupler pin also inserts through the hole in the pin channel on the coupler. Mounting the Attachment Park the machine on a level surface. Pull the coupler pins outward and rotate 90° to lock in the disengaged position. g373477 Figure 5 Lower the attachment coupler until the...
Routing the Hydraulic Hoses Shut off the machine engine, wait for all moving parts to stop, ensure that the parking brake is engaged, and remove the key. Route the hydraulic hoses. Note: When changing attachments on the machine you may need to relieve stored hydraulic pressure by slightly loosening hydraulic lines on the snow thrower or wiggle the joysticks on machine.
Page 8
Gather the hoses and secure them in the hose strap on the machine. g385655 Figure 9 Start the machine. Use the controls to move the attachment in all directions to cycle the hydraulic fluid. Lower the attachment and shut off the machine. Check and fill the hydraulic fluid;...
Product Overview • Use the right angle lever to rotate the chute. Controls g383364 Figure 10 1. Angle levers 3. Attachment coupler lever g383346 Figure 13 2. Engage the attachment • Use the attachment coupler lever to raise or lower the attachment.
Removing the Attachment Operation Stop machine on a level surface. Operating the Snowthrower Lower the attachment until the edge is 1-2 inches from the ground. Important: Raise the snowthrower when Shut off the engine, wait for all moving parts to transporting it.
Operating Tips • Become familiar with the area you are operating the attachment; hidden obstructions such as curbs and pipes can damage your attachment or machine. • Lower the attachment when not in use to prevent possible injury. • Always operate the machine at a safe speed in case you hit hidden obstructions.
Service Interval: Before each use or daily Loosen the 4 motor bolts. Before storage Use Boss Snowrator Hydraulic Fluid or SAE 20 oil. Raise the attachment all the way up using the hydraulic controls. Remove the rubber plug on the chain housing...
Figure 22 Note: Replacement hardware is available through an Authorized Boss Dealer or Boss Technical Service. Remove the hardware holding the cutting edge Adjusting the Skids to the blade. Check the skids to ensure that the auger does not contact the paved or gravel surface.
Page 14
Note: To quickly adjust the skids if they loosen, rest the poly edge on the pavement, then adjust the skids down. g383363 Figure 23 Raising the Skids Park the machine on a level surface and raise the attachment. g385838 Figure 24 Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.
Storage Storing the Attachment Before long term storage, wash the attachment with mild detergent and water to remove dirt and grime. Place the chute in the upwards position. Check the condition of the scraper blade. Check and tighten all bolts, nuts, and screws. Repair or replace any damaged or worn parts.
1. Check the hydraulic fluid level; refer to move slowly. your Snowrator MAG Owner's Manual. 2. The hydraulic fluid level is low and the 2. Slow the Snowrator MAG gradually Snowrator MAG was stopped quickly. before coming to a stop when the hydraulic fluid is low.
Need help?
Do you have a question about the Snowrator MAG and is the answer not in the manual?
Questions and answers