FirePro FP-08850 Manual

FirePro FP-08850 Manual

Discharge delay module

Advertisement

Quick Links

1
Introduction .......................................................................................................................... 2
1.1
General Information ............................................................................................... 2
1.2
Discharging Additional FirePro Generators .................................................... 2
1.3
Delaying Discharge ............................................................................................... 2
2
Components List ................................................................................................................. 2
3
Design Considerations ....................................................................................................... 2
3.1
Normal Output ......................................................................................................... 2
3.2
Discharge Delayed Output .................................................................................. 2
3.3
How to install a Discharge Delay Module ....................................................... 3
3.4
3.5
Mounting ................................................................................................................... 4
3.6
Cabling Requirements .......................................................................................... 4
3.7
Multiple Discharges & Voltage Limitations ..................................................... 4
3.8
Connecting Multiple Modules ............................................................................. 4
3.9
Connecting Multiple FirePro Generators ......................................................... 5
4
Installation ............................................................................................................................ 6
5
Wiring Diagram .................................................................................................................... 7
6
Programming......................................................................................................................... 7
6.1
Programming Module Version 1 - 2.1 ................................................................. 7
6.2
Programming Module Version 3 ....................................................................... 8
7
Commissioning .................................................................................................................... 9
8
Servicing and Maintenance .............................................................................................. 9
9
Operation .............................................................................................................................. 9
10
Troubleshooting ................................................................................................................. 10
11
Specifications ...................................................................................................................... 10
Discharge Delay Module
Contents
Model 08850
Rev 3.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FP-08850 and is the answer not in the manual?

Questions and answers

Summary of Contents for FirePro FP-08850

  • Page 1: Table Of Contents

    Discharge Delay Module Model 08850 Rev 3.1 Contents Introduction .......................... 2 General Information ....................2 Discharging Additional FirePro Generators ............ 2 Delaying Discharge ....................2 Components List ......................... 2 Design Considerations ....................... 2 Normal Output ......................2 Discharge Delayed Output .................. 2 How to install a Discharge Delay Module ............
  • Page 2: Introduction

    24vDC Max 4 x Firepro Generators Where risk requires a more FirePro Units to be used, or a delay in the activation. The Discharge Delay module must be used. The module will activate FirePro generators sequentially in multiples of the quantities as per the available power supply.
  • Page 3: How To Install A Discharge Delay Module

    Connecting ADDITIONAL UNITS USING for DELAYED DISCHARGE This shows 3 x FirePro Generators operating This shows 2 x Firepro Generators operating ONLY immediately (through the Normal Activation Circuit) AFTER DELAY. The 3k3Ω EOL resistor must be in and 1 FirePro unit firing after a delay.
  • Page 4: Mounting

    Voltage 24vDC Max = 4 Units If a risk area requires a greater number of FirePro generators to be discharged than the standard panel can provide, Discharge Delay modules can be used. The module will discharge generators in multiples up to the maximum as above.
  • Page 5: Connecting Multiple Firepro Generators

    Connecting Multiple FirePro Generators 3.10 If multiple FirePro Generators are being installed on a single output, they must be connected using the FP-08919 Splitter Lead. The Splitter Lead enables the activation current to pass uninterrupted to all connected FirePro generators and allows for continuous monitoring.
  • Page 6: Installation

    1. FirePro generators must remain disconnected until system is completed and fire control panel is no longer in a fault or alarm condition. The FirePro Universal Test Lamp (P/N FP- 08800) can be used to take the panel out of a fault condition.
  • Page 7: Wiring Diagram

    (See FP-08450 or FP-08451 Manual) The Delay Timer Switch allows for the activation of the connected FirePro generators to be delayed for a period of up to 240 seconds after the FIP has entered an alarm condition.
  • Page 8: Programming Module Version 3

    (See FP-08450 or FP-08451 Manual) The Delay Timer Switch allows for the activation of the connected FirePro generators to be delayed for a period of up to 255 seconds after the FIP has entered an alarm condition.
  • Page 9: Commissioning

    Commissioning should be performed when the siren and shutdown relays are connected, and fire control panel is not in an alarm/fault condition. 1. Isolate and disconnect the any installed FirePro aerosol generators. This should generate a fault on the fire control panel.
  • Page 10: Troubleshooting

    (3 Beeps) connection to FirePro generators extension cables. Inspect condition of FirePro Number of installed generators Generators. exceeds maximum Check internal battery of FirePro Test lamp. FirePro Generators have discharged For additional assistance contact your supplier. Specifications FP-08850 Dimensions...

Table of Contents