Page 11
Dear users, thank you for purchasing the constant voltage constant current DC power supply produced by Hangzhou Ruideng Technology Co., Ltd. In order to let you know more about the full function of this product, get a better experience and avoid misuse. Please read this instruction carefully before using it.
RD power supply*1 X25A output cable*1 Micro Communication cable*1 Input AC Power Cord*1 这个头有好多标准 (inside X25A bag) External Temperature Sensor*1 Backup Fuse*1 1.2 Technical Parameter Model RD6006-W RD6012-W RD6018-W RD6024-W RD6006P-W RD6012P-W Input voltage range 6-70.00V 7-70.00V Output voltage range 0-60.00V...
Page 13
Model RD6006-W RD6012-W RD6018-W RD6024-W RD6006P-W RD6012P-W Output current accuracy ±(0.5%+5 digits) ±(1‰+6 digits) Battery voltage accuracy ±(0.5%+3 digits) Default battery charging 10mA 100mA 10mA cutoff current 100mV Output ripple typical @12A; ② 100mV 250mV@6A 20mV (VPP) 150mV @24A Working temperature range -10℃~40℃...
protection Screen brightness setting 0-5(6 level) Screen 2.4 inch color HD display Weight(with package) Product dimension 17*8.5*33 17*8.5*33 17*8.5*33 (cm) USB communication WiFi communication ①:Accuracy test method:1 digit is the minimum resolution, so the error under 5V is ±(5*0.5‰+4*0.001)=±0.0065V. ②:Ripple measurement method: noise and ripple are measured at X1 range, AC coupling, 20 MHz of bandwidth on your oscilloscope with a 0.1uF parallel capacitor at the output terminals, pure resistor as load.
Page 15
P: Input power socket Q: Rocker switch R: External temperature sensor socket S: Heat dissipation holes 1.4 Operation Instruction After power-on, it will show boot image first, and then enters the main page. 1.4.1 Main Page AA: Actual output voltage value AB: Actual output current value AC: Output power AD: Current data group...
Page 16
At main page you can press button to change the display style between Traditional Style, Detail Style and Curve Style, the display style will not be saved automatically, you need to set default boot display at section 1.4.2.6 Main Page Style Setting. 1.4.2 Operation Introduction In the menu operation, the icon in red or cursor is the currently selected menu, press...
Page 17
encoder potentiometer to adjust the output value directly. And you will not set the value which exceeds the limit in this way, press button to move the cursor. Of course you can use keypad to type in the value, and press to confirm, and it will save the set value and set current range, if you set a value exceeds the limit, it will prompt like what shows in Figure 1.
is the default data group, when you edit the settings and press button or rotate encoder potentiometer to change the setting and press encoder potentiometer to return, it will be stored into automatically, or you go to the data group setting menu, change the setting and press encoder potentiometer to return, it will save too, and it will not save by other settings.
Page 19
Buzzer is set to ON by default,it will show on the top, and you can hear the beep when press the button. When set it OFF, it will show , there will not be beep when press the button. Backlight is set to level 4 by default, it can be set between level 0-5.
Page 20
Communication Sub-menu(figure 8): Interface is set to USB by default, you can also set it to WIFI/TTL/RS485, USB means the micro USB port, you can see on the top when set it USB, and when the communication starts, it will show You need to insert a WIFI board to use the WIFI function, and it will show figure 9 on the top, and when the communication starts, it will show...
Page 21
You can press to enter the system setting menu, then press and it will be switched to display style menu(as shown in figure 10): you can press to enter the sub-menu. Layout Sub-menu: figure 12 Digits Style is set to Normal by default, you can set it to Normal/7-Seg V1/7-Seg V2(as shown in figure 11).
Page 22
After setting, press the encoder potentiometer to return and save setting. 1.4.2.8 System Information You can press to enter the system setting menu, and then press button 3 times to enter the system information menu(as shown in figure 15). Product Model is the device name, Product SN is product serial number,...