Quoizel CCR8410CU Assembly Instruction

Please go to www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Light Source: (3) B10 Candelabra Base bulbs 60W Maximum.
Estimated Assembly Time:
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to ensure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Fixture can only be mounted in the direction indicated on page 2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x 1
Alternate
B Mounting screw
x 2
STEP 1 - Insert Glass Panels
A. Insert the U-shaped foam end of the
Glass Panel (D) into the slot in the
bottom of the cage and fasten with
the tabs in the top edge of the cage.
-
STEP 2 Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Outlet
Box
Mounting Screw
or Alternate Short
Mounting Screw
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
2016 QuoizelInc.
Assembly Instruction Sheet #IS-CCR8410CU
for product cleaning tips. Go to the
20-30 minutes
Fixture Body
C
x 1
D
Figure 1
Outlet Box Screws
(not included)
A
Supply Wires
with Ground Wire
Figure 2
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
For Style CCR8410CU
Care + Maintenance selection.
-
STEP 3 Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw
or alternate short
mounting screw on the
Crossbar Assembly (A)
by unscrewing the
preassembled hex nut
Glass Panel
and lock washer and
x 4
then screwing the
mounting screws or
alternate short mounting
screws in or out of the
crossbar until the correct
C
length is achieved. Once
the backplate and
Fixture Body (C) is
Tab
secure, remove the
mounting ball and
Fixture Body (C) and
proceed to Step 4.
Slot
STEP 4 - Wire Connections
D
A. Use standard wire connectors (not included) to make all wire
U-shaped
connections. Twist connectors until wires are tightly joined together.
Foam
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
from outlet box
Black wire from
.
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Bare, or Green
Ground wire
from outlet box
1of2
Mounting Screw
or Alternate Short
Mounting Screw
A
Hex Nut and
Lock Washer
Backplate
Figure 3
White wire
OR
Green Ground Screw
on the Crossbar
Figure 4
_R1
Mounting
Ball
C
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Ground wire
from fixture
ReleasedDate:2016-11-18