Subscribe to Our Youtube Channel
Summary of Contents for JLB Racing CHEETAH
- Page 1 CHEETAH INSTRUCTION MANUAL ShenZhen Golden cheetah technologyCo.,Ltd WWW.jlbracing.cn...
-
Page 2: Product Contents
INTRODUCTION Thank you for purchasing this JLB racing model.This manual contains instructions on operating and maintaining the Cheetah .Please take a monent to read through this manual to familiarize yourself with this model. FEATURES Bright front LED The gear box structure is easy to repair... - Page 3 IMPORTANT INFORMATION The Cheetah is a powerful RC car that will bring much enjoyment.However,improper use can cause damage and bodily injuries.Please read the following information carefully to avoid casualties. WARNING: This model can be operated with Ni-MH or Lithium Polymer batteries.
-
Page 4: Parts Name
PARTS NAME LED Light Front Bumper Down Suspension Arm Shock Steer Block Shock Stay Wheel Hex Hub Servobuckle Steering Servo Turnbuckle(toe link) Body Mount Bracket Receiver Battery Tape Electronic Speed Control Battery Motor Center Shaft Motor Mount Chassis Motor lock Shock Stay TOP Suspension Arm Second floor... - Page 7 ELECTRONICS SRTUP Servo Receiver Black wire “C” Blue wire “B” Motor Set Key Switch Red wire “A” Begin to use the new ESC 1.Connect the ESC,motor,receiver,battery and servo according to the following diagram The #A,#B,#C wires of the ESC can be connected with the motor wires freely.If the motor runs in the Power opposite direction,please swap any two wire...
-
Page 8: Front Gear Box Assembly
Front Suspensive Assembly 15X10X4 CORRECT Front Gear Box Assembly... -
Page 9: Shock Assembly
Shock Assembly Shock Assembling Steps: 1.Fill shock body with 4/5 silicone fluid(purchase seperately),pump the shock shaft up and down to remove any air bubbles. 2.Wait the air bubbles pumped out,then pull down the shock shaft to the bottom,fill the silicone fluid up to 2 mm,after that ,tighten the shock head 1. 3.Install the spring,shock assembling finished. - Page 10 Rear suspensive arm Assembly Adjusting the Slipper clutch NOTE: the slipper clutch adjustment too loose or tight may result in damsge the gear during racing. Tail wheels Assembly...
-
Page 11: Steering Assembly
Steering Assembly NOTE: Rotating the nut to seek suitable degree of tightness. Motor Mount Assembly NOTE: Adjustment 86 to seek suitable degree of tightness. Chassis Assembly... - Page 12 ALL Assembly TIPS: The slipper clutch adjustment short cut Use wrench 10mm key,Insert the hold as the picture below. Grasp the both sides of rear wheels,rotate in the same direction.
- Page 13 SPARE PARTS EA1001 EA1002 EA1003 EA1004 EA1005 EA1006 PWM2.5X4 PM4X10 Down suspensive TOP suspensive EA1008 EA1009 EA1007 EA1010 EA1011 EA1012 PM3X8 PM3X12 PM3X10 KM3X12 PM3X116 EA1014 EA1015 EA1016 EA1017 EA1018 EA1013 PM3x10 PIN3X17 PM3x12 PM3X10 IM3X3 EA1020 EA1021 EA1022 EA1023 EA1024 EA1019 right x1...
- Page 14 SPARE PARTS EA1043 EA1045 EA1044 EA1046 EA1047 EA1048 iM4x4 EA1049 EA1050 EA1051 EA1052 EA1053 EA1054 FRONT KM3X12 REAR KM3X12 PM3X8 KM2.5*8 EA1060 EA1055 EA1058 EA1056 EA1057 EA1059 pM3x12 pM4x12 EA1062 EA1063 EA1061 EA1066 EA1067 EA1068 11.1V-4000MAH EA1076 EA1075 EA1077 EA1071 EA1069 EA1070 PM4X10...
- Page 15 SPARE PARTS SW012 SW007 SW009 SW010 SW008 SW011 KM2.5x8 pM2.5x8 KM3x12 KM4x20 KM4x10 pwM2.5x4 SW013 SW014 SW015 SW016 SW017 NT001 pM4x12 M3 NYLON pM3x20 pM4x10 IM3X3 IM4x4 NT002 OR001 OR003 OR004 OR002 NT003 ID12x1.5mm ID 16x1.0mm ID 3.0x2.0mm ID 4.5x1.5mm M5 NYLON EA1080 EA1081...
- Page 16 Bill Of Material...
- Page 17 Tough Suspension CHEETAH giving you the assurance that you'll be able to deal out the same abuse that all the other nitro-powered trucks can handle! Beefy parts mean the CHEETAH can take plenty of abuse and punishment, giving you plenty of big-air thrills.
- Page 18 Shenzhen Golden cheetah technology co;Ltd WWW.Jlbracing.cn Tel： 86-755-21013805 Fax：86-755-21013731 Email contact：jlb@jlbracing.cn Address: 2F D-Building Jinhao pioneer Park Dafu Industrial Zone Guanlan city Longhua new district Shenzhen China 518110...
Need help?
Do you have a question about the CHEETAH and is the answer not in the manual?
Questions and answers