Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Tenveo TENVEO-KZ1
- Page 1 USER MANUAL...
-
Page 3: Table Of Contents
Contents ---------------- 1 What’s in the box ---------------------------------------- ------ Function------------------------------------------------------------------------- Installation --------------------------------------------------------------------- Connection ------------------------------------------------------------------- How to use -------------------------------------------------------------------- Function keys ---------------------------------------------------------------- Keyboard/joystick operation -------------------------------------------- Technical parameters -----------------------------------------------------... -
Page 4: What's In The Box
1 What’s in the box 1 x Joysticker PTZ Keyboard Controller 1 x RS232 cable 2.8 meters 1 x Power adaptor 1 x User manual 2 Function · VISCA, Pelco-D and Pelco-P protocol support. ·Large LCD Menu display. ·Key-press “BEEP” confirmation (optional – set on or off). ·Pan, tilt, zoom, iris and focus control. -
Page 5: Connection
4 Connection 1 RS232 connection For connect the DB9 port of the KB to the mini Din8 (VISCA) port of the camera with pin-out as follows: KB Tx – Pin 3---------- Camera Rx - Pin 5 KB Rx – Pin 2---------- Camera Tx - Pin 3 KB Gnd –... - Page 6 Note: the RS232 cable supports a maximum length of 10m. If there are interfaces of RS232 and RS485 in and out on the camera, RS232 can connect more than two cameras in series to realize that one control keyboard controls multiple cameras. If the camera only has RS232 out interface, it only supports single camera control.
-
Page 7: How To Use
KB Ta – Pin 1---------- Camera (+) KB Tb – Pin 2---------- Camera (-) KB Gnd – Pin 5---------- Camera (G) (if present – some cameras will not require a G How to make the cable connected Note: RS485 cable length supports more than 100m. RS485 can connect multiple cameras in series to realize one control keyboard to control multiple cameras. - Page 8 5.3 How to control 5.3.1. 1 keyboard controller controls 1 camera: By RS232 Control Just connect the camera and keyboard through RS232 Cable. There is no need for any setting of the keyboard controller and camera, you can control the camera directly. 5.3.2.
- Page 9 5.3.3 Keyboard controller control 3 cameras : RS485 Control : Video:https://youtu.be/srX08jmYO3U Keyboard setting: Camera ID: 001, 002, 003 Protocol: VISCA Baud: 9600 Camera setting: Camera1: Dip setting: SW1: Dip 1----ON, others dips are off Camera2: Dip setting: SW1: Dip 2----ON, others dips are off Camera3: Dip setting: SW1: Dip 1 and Dip 2----ON, others dips are off 5.3.4 Keyboard controller control 4 cameras: RS485 Control Keyboard setting:...
-
Page 10: Function Keys
6 Function keys 6.1 Function keys on front keyboard controller 6.1.1 Function keys: 【Esc】 Back to previous menu. 【Setup】 Press for 3 secs to set up key parameters. 【Search】 Inquire The Protocol & Baud Rate Of Current Address. 6.1.2 Speed doom Setup and recall keys: (This function might be not available for part of protocols if the speed doom does not have this function) 【F1】Auto focus,Only used in Sony camera control mode. - Page 11 together with control knob or function key. 【RUN】 In Sony camera control mode:On/Off the backlight.In other camera control mode: Recall the stored PATTEN. This key should be used together with number key and [Enter] key. 【PATROL】 In sony camera control mode:PTZ reset.In other camera control mode:Start/Esc to patrol record of speed door,press this key to Enter patrol set, and Esc to patrol set press this key again This key should be used...
- Page 12 【IRIS- 】 Downsize aperture, 【AUX ON】 AUX key turns on. Turn on AUX key. This key should be used together with number key and Enter key. 【AUXOFF】 AUX key turns off. Turn off AUX key. This key should be used together with number key and Enter key. 6.2 Keyboard controller protocol and Baud rate Setup E.g.
-
Page 13: Keyboard/Joystick Operation
7 Keyboard/Joystick operation 7.1 Basic Control 7.1.1 Pan & Tilt Control Joystick movement provides variable speed pan and tilt of the camera head. 7.1.2 Zoom Control Rotation of the joystick controls variable speed zoom of the lens. Clockwise rotation of the joystick = zoom in. Counter-clockwise rotation of the joystick = zoom out. -
Page 14: Technical Parameters
8 Technical parameters Model TENVEO-KZ1 Protocol Pelco-D, Pelco-P, VISCA Baud rate(bps) 1200bps, 2400bps, 4800bps, 9600bps, 19200bps Control Address Control 255pcs PTZ at the most, address code:1-255 RS485 half-duplex, RS422 full-duplex Communication Mode RS232 serial port Communication Range RS485, RS422: more than100m, RS232: 10m...
Need help?
Do you have a question about the TENVEO-KZ1 and is the answer not in the manual?
Questions and answers