Summary of Contents for Strack SN 2960
- Page 1 CONTROL PANELS OPERATING INSTRUCTIONS Manufactured by TECAPRES ® Service and distribution in countries D, A and CH by...
-
Page 2: Table Of Contents
Release of the pressure at a gas spring bloc ..............11 Increase of the pressure at a gas spring ................11 2.3.2 STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de... -
Page 3: Safety Instructions
Please read and observe the following operation instructions before installation and start-up and all further works with the control panel SN 2960 / SN 2962 / SN 2963 / SN 2965. Special designs of the STRACK control panels must be used according to these operating instructions. -
Page 4: After Receipt Of Delivery
Please contact STRACK NORMA GmbH & Co.KG in Lüdenscheid to get further information: Phone: +49 2351 / 8701 - 0 (head office) 2.3.4 STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de... -
Page 5: Features
By connecting of the gas springs with high-pressure hoses, it is guaranteed that all gas springs have the same pressure. Due to a control panel (SN 2960 / SN 2962 / SN 2963 / SN 2965) fitted on the tool, all gas springs are simultaneously filled or released. - Page 6 Release valve per unit Control unit stage 3...8 Quick coupling Control unit stage 2 Control unit stage 1 Basic unit 2.3.6 STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de...
-
Page 7: Installation
Control panels SN 2960 / SN 2962 / SN 2963 / SN 2965 3. Installation The control panels SN 2960 / SN 2962 / SN 2963 and SN 2965 can be connected with a plate by means of screw-fixing. During the installation of the control panel in the upper part of the tool, the screws must be secured with screw-locking adhesive (medium-strength) due to arising vibration exposure. -
Page 8: Sn 2963
The filling of the tankplate over the control panel SN 2963 can be effected as well as it is the case at the control panel SN 2960 by means of a boring with o-ring sealing directly on the plate. 3.1.4 SN 2965... -
Page 9: Initial Start-Up
Adjust the pressure reducer to maximal gas spring filling pressure, e.g. 150 bar. (Continuation next page) 2.3.9 STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de... -
Page 10: Modification Of The System Pressure Of The Gas Springs
4.2 Modification of the system pressure of the gas springs The control panels allow a simultaneously control of several gas springs. 2.3.10 STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de... -
Page 11: Release Of The Pressure At A Gas Spring Bloc
In such a case, you have either to increase the pressure again or to adjust the pressure controller to this new value. 2.3.11 STRACK NORMA GmbH & Co. KG · Königsberger Str. 11 · D-58511 Lüdenscheid · Tel +49 2351 8701-0 · www.strack.de... - Page 12 STRACK NORMA GmbH & Co. KG Königsberger Str. 11 D-58511 Lüdenscheid Postfach 16 29 D-58466 Lüdenscheid Tel +49 2351 8701-0 Fax +49 2351 8701-100 Mail info@strack.de Web www.strack.de 08.2018...
Need help?
Do you have a question about the SN 2960 and is the answer not in the manual?
Questions and answers