Summary of Contents for WatchGas BEACON SOUNDER
- Page 1 DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 USER MANUAL BEACON SOUNDER we watch gas where you can't...
-
Page 2: Table Of Contents
DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 BEACON SOUNDER CONTENTS DESCRIPTION WARNING DISPOSAL 1. PRODUCT OVERVIEW 1.1 PCB Layout 1.2 Drilling Template 2. DIP SWITCH SETTINGS 3. MOUNTING INSTRUCTIONS 4. GENERAL SPECIFICATION 5. SERIAL PROTOCOL SPECIFICATION 6. LIMITED WARRANTY... -
Page 3: Description
Beacon Sounder. Ensure you read this user manual fully before installing and opera- ting the Beacon Sounder. If you are installing this Beacon Sounder for use by others, you must leave this manual with the end user. Installation must be carried out, in accordance with latest codes and regulations, by a qualified electrician. -
Page 4: Product Overview
DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 BEACON SOUNDER 1. PRODUCT OVERVIEW 1.1 PCB LAYOUT 1. Sounder 2. 10 pin DIP switch 3. 6 pin DIP switch J2. Communication input J4. Terminal block 7 pins + = Supply - = Ground BU = Blue light... -
Page 5: Dip Switch Settings
DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 watchgas detection 2. DIP SWITCH SETTINGS DIP SWITCH 1 / 2 SOUND SELECTION alternating low / high beeps continuous 50 Hz changing frequency fast continuous 2700 Hz DIP SWITCH 3 / 4 RED LIGHT continuous fancy loop... - Page 6 DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 BEACON SOUNDER DIP SWITCH 1 L Link red and Sounder analog inputs ON = Linked OFF = Unlinked DIP SWITCH 2 T Trigger ON = Rising trigger OFF = Falling trigger DIP SWITCH 3 FN Function...
-
Page 7: Mounting Instructions
3. MOUNTING INSTRUCTIONS • Use drilling template to make holes in the mounting surface. • Mount the Beacon Sounder with the supplied screws, washers and nuts. • Always mount with the glass upright. • Ensure all rubber gaskets are placed correctly. -
Page 8: General Specification
Specification rev 1.0 INTRODUCTION This document describes how to control and connect the Beacon Sounder PN: Air-Be- ac-010 over a serial interface. This serial interface can be used to select colour, display effect and sound effect. If the serial input is used, the digital I/O inputs are no longer enabled. - Page 9 CRIMP CONTACT GOLD PLATED 08-55-0111 Molex DIPSWITCH SETTING Set DIP switch FN 3 to “ON” to configure the Beacon Sounder to use a serial input. DIP SWITCH 3 FN Function ON = J2 TTL Communication protocol OFF = J4 terminal block input...
- Page 10 NOTE This command has to be repeated at least every 15 seconds. If no command has been received for 15 seconds, the Beacon Sounder will switch off. The CRC byte is calculated as following: crcByte = toHex ( (Byte[0] + … + Byte[5]) & 0xF );...
- Page 11 DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 watchgas detection LIGHT AND SOUND MODES The following sound and light modes are implemented: VALUE SOUND MODE (BYTE 5) LIGHT MODE (BYTE 1) Disabled Flashing 10Hz 50% duty Continuous 2700Hz low Looping Changing frequency (fast) low...
- Page 12 DocuSign Envelope ID: AD1219C0-C292-4C55-B2EE-1190F300B975 BEACON SOUNDER EXAMPLE CODE The following C code can be used to implement this protocol. // Range for r,g,b is 0 .. 255. // Run this function every 5 .. 10 seconds void set(BSoundMode s, BLightMode m, uint8_t r, uint8_t g, uint8_t b) { // Transmit new values char cmd[9];...
-
Page 13: Limited Warranty
For permission requests, contact WatchGas Detection.