Traxxas 7185A Instructions

1/16 E-Revo LED Light Kit Instructions
Note: Ensure vehicle battery is unplugged before beginning installation. Retain and reuse all parts and fasteners (unless otherwise noted).
Your model may differ slightly from the one shown in the illustrations.
Kit Contents:
1 - LED lighting module
(included with part 3
#7185A only)
2 - Power tap
3 - LED harness
4 - Front bumper
5 - Rear bumper
6 - Zip ties (3)
Tools Needed:
• 2.5mm hex driver
• 2.0mm hex driver
• 1.5mm hex driver
• Wire cutter (to trim
zip tie excess)
Tip: Sort the hardware by assembly as you remove them so you can easily locate the
correct hardware during reinstallation. (A)
A
Remove These Parts to Allow Installation of the
Front bumper
Servo guard /
Gear cover
cover plate
LED Harness Installation
1. Remove the parts shown in Fig. A.
2. Install the LED lighting module and route the
wires through the loop guide (B).
3. Route the short end of the LED harness through
the front body mount (D).
4. Snap the LEDs into the new front bumper (C).
5. Route the wires against the front bumper; then,
install the bumper on the front bumper mount.
Secure the harness to the front body mount with
a zip tie (trim excess) (C, D).
6. Continue to route the LED harness down the center of the chassis as shown in Fig. J.
Plug the LED harness connector into the LED lighting module. Route the module wires
and the LED harness around the transmission and secure them with a zip tie
(trim excess) (J).
Wiring Layout Wiring Layout
J J
Zip tie
LED lighting module
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com
5
4
2
1
*
* Larger red connector for telemetry use only
LED Light Kit
Motor
ESC
Wire clamp
Receiver box cover
B B
Loop guide Loop guide
LED lighting LED lighting
module module
Zip tie
Receiver box
(Receiver box cover and wire clamp removed
from the wiring layout for clarity)
C
6
LED harness
7. Fully loosen the two rear shock mount
screws, raise the rear shock mount
slightly, and route the long end of the
LED harness under the shock mount
(between the shocks). Tighten the rear
shock mount screws; then, continue
routing the LED harness toward the
rear bumper (E).
CAUTION: Do not pinch the wiring
between the shock mount and the chassis.
8. Snap the LEDs into the new rear
bumper (F).
Rear bumper
(under wing)
9. Route the wires against the rear
bumper; then, install the bumper on the
rear bumper mount. Secure the harness
to the rear body mount with a zip tie
(trim excess) (F, G). Plug the LED harness
connector into the LED lighting module.
10. Thread the red wire from the LED
lighting module through the opening
in the receiver box cover and plug the
connector into any available channel in
the receiver box (DO NOT use the V/T or
RPM ports) (H).
Note: If you install the included power
tap, the red female connector from the
power tap can be used to connect the
temperature/voltage sensor (part #6523,
sold separately) to the electronic speed
control (ESC).**
11. Reinstall the ESC, the receiver box cover,
the wire clamp, the motor, and the gear
cover.
Note: Ensure that the blue o-ring is properly
seated in the groove around the receiver
box cover. Check for proper adjustment of
the gear mesh. Refer to the vehicle Owner's
Manual for detailed instructions.
12. Plug the battery into the High-Current
Connector on the ESC (I).
13. The lights will turn on when the ESC is
turned on.
Rear shock mount
TR A XXA S. c om
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
Covers Part(s) #7185A, 7186A
D
LEDs Front bumper
Front
bumper
mount
E E
Rear shock mount screws Rear shock mount screws
F
G
Zip tie
H H
I
Power Tap Power Tap
Zip tie
Wing removed to show
rear bumper location
Zip tie
LED harness LED harness
Rear bumper
LEDs
LED
harness
Rear
bumper
Receiver box cover Receiver box cover
Blue O-ring Blue O-ring
High-Current Connector
on the ESC
HKC20057-R00 Rev. 200724
HKC20057-R02 Rev 201026