SMART TamperProof TL-2100S Installation And Use Instructions And Warnings

TL-2100S FallGuard™ Safety Auto-Reset™
CAUTION: If using this monitor with the Change Pad Indicator™ Timed Sensor Pads, this monitor will not indicate when pad life has expired. The pads will still function normally. Call (800) 650-3637 for more information.
WARNING: Failure to comply with the warning may result in injury or death. This device is not suitable for all individuals. Other devices may be required. This device is not a substitute for visual monitoring by a caregiver. The
manufacturer does not claim that this device will stop elopement and/or stop falls. This device is designed to augment caregivers' comprehensive resident mobility management program.
instructions and Legal Disclaimer.
The Smart Caregiver Corporation TL-2100S Monitor is designed to be installed by the end-user. As such, it is the entire responsibility of the buyer to insure that the system is properly installed and tested. Further, the system is not designed to
replace good caregiving practices including, but not limited to:
A.) Direct patient supervision
B.) Adequate training for staff personnel for fall prevention and elopement
C.) Testing of the system before each use
WHERE PERMISSIBLE, IT IS THE SELLER'S INTENT TO LIMIT ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO REFUND OF THE PURCHASE PRICE OR REPLACEMENT OF THE GOODS. SELLER DISCLAIMS ANY
LIABILITY FOR COMPENSATORY OR OTHER DAMAGES ARISING OUT OF THE USE OF THE GOODS.
WARNING: The manufacturer does not claim that this device will stop elopement and/or stop falls. This device is designed to augment caregivers' comprehensive resident mobility management program. This product is to be used by a
licensed caregiver only.
Protective Boot may contain trace amount of chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
Limited Warranty: Seller warrants that the goods sold will be free from defects of workmanship and manufacturing, for a period of one year from the date of sale. Other than this limited warranty, seller makes no express or implied
warranties. Except for this limited warranty, NO EXPRESS OR IMPLIED WARRANTIES ARE GIVEN AND NO AFFIRMATION OF SELLER, BY WORDS OR ACTION, WILL CONSTITUTE A WARRANTY. THE GOODS BEING PURCHASED ARE BEING
SOLD ON A "WITH ALL FAULTS" BASIS. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE GOODS IS WITH THE BUYER. SHOULD THE GOODS PROVE DEFECTIVE FOLLOWING THEIR PURCHASE, THE BUYER, AND NOT THE
MANUFACTURER, DISTRIBUTOR OR RETAILER, ASSUMES THE ENTIRE COST OF ALL NECESSARY INSTALLATION, SERVICING OR REPAIRS.
CE marking concerning medical appliances.
Device in contact with patient, excluding the heart area.
Follow the user manual instructions.
Protected against the ingress of foreign object ≥ 12.5mm &
against dripping water when tilted up to 15°.
S M A R T C A R E G I V E R CO R P O R AT I O N
1229 North McDowell Blvd., Petaluma, CA. 94954 | Tel: 800-650-3637
csr @ smartcaregiver.com | www.smartcaregiver.com
Test this device before each use. Read the
Please contribute to protect the environment
by observing the disposal instructions.
Caution: Read the instructions for use.
Environment conditions of transport and storage between uses:
Temperature: -25°C to +70°C ;
Humidity: < 93% RH non-condensing
Environment operating conditions:
Temperature: 5°C to +40°C ;
Humidity: 15% to 93% RH non-condensing
Pressure: 700hPa to 1060hPa
Bed Sensor Pads
BED PLACEMENT .
• Place the pad under the resident's shoulders to be
alerted when the resident sits up in the bed.
• Place the pad under the resident's lower back/buttocks to
be alerted when the resident vacates the bed.
• Place the monitor out of reach of the resident. Suitable
mounting locations include: the back of headboard, the wall
or under the bed. Make sure the resident cannot tamper with
the monitor.
TEST THE SYSTEM
• Plug the pad into the monitor and apply pressure
to the pad to activate the system. The monitor will beep
twice when active.
• The alert will sound when pressure is released
from the pad. Press the "Reset" button on the front of the
monitor to silence the alert.
Chair Sensor Pads
WHEELCHAIR/CHAIR PLACEMENT
• Center the pad on the chair seat.
• Place the monitor out of reach of the resident. Suitable mounting locations
include: the back or handle of the wheelchair. Make sure the resident
cannot tamper with the monitor.
TEST THE SYSTEM
• Plug the pad into the monitor and apply pressure to the pad to activate
the system. The monitor will beep twice when active.
• The alert will sound when pressure is released from the pad.
Press the "Reset" button on front of the monitor to silence the alert.
Seat Belt

SEAT BELT PLACEMENT

• Unscrew the one screw on either side of the wheelchair that holds the seat
in place.
• Attach the seat belt to the wheelchair by lining up the grommet holes on
the seat belt with the screw hole and re-insert screws through both the
seat belt and the wheelchair to hold the seat belt in place. Make sure the
screws are tightened.
• Adjust the seat belt to the desired length using the black buckle that holds
the adjustment strap in place.
• Place the monitor out of the reach of the resident. The suitable mounting
location is the back of the wheelchair, so that the resident cannot tamper
with the monitor.
TEST THE SYSTEM
• Buckle and unbuckle the seat belt to set off the alert. The monitor is now
active. The alert will sound whenever the seat belt is unbuckled.
• When the system is activated, press the "Reset" button on front of the
monitor to silence the alert.
Floor Mats

FLOOR MAT PLACEMENT

• Place the Floor Mat in the desired location such as a critical doorway or
next to a bed.
• Place the monitor out of the reach of the resident.
TEST THE SYSTEM
• Step on the Floor Mat to set off the alert. The monitor is now active.
The system will sound any time weight is on the Floor Mat.
• When the system is activated, press the "Reset" button on front of the
monitor to silence the alert.
Need Set-up Help? (800) 650-3637
1 2