Summary of Contents for FLEET Kombi Ranger
- Page 1 User Manual Ranger Fleet (Line Markers) Limited, Fleet House, Spring Lane, Malvern, Worcestershire, WR14 1AT Tel: 01684 573535 sales@flmuk.com www.fleetlinemarkers.co.uk...
- Page 2 Markers) Limited. Founded in the 1950’s Fleet are regarded as the world’s leading expert in the field of line marking. Of course its not just the machines that Fleet are famous for, our range of line marking paints are used around the world, wherever the pitch, whatever the occasion.
- Page 3 ASSEMBLING YOUR KOMBI RANGER MARKER PREPARING FOR USE Carefully remove the machine and accessories from packaging. Insert handlebar section; adjust to suit user’s height and tighten using thumb screws. Bar ends can be adjusted to suit hand position using the supplied 5mm allen key.
- Page 4 9. You will need to connect the orange and blue pipes to the side of the ma- chine, to do this the orange pipe connects to the fitting furthest forward on the machine. The blue pipe connects to the connection furthest back on the machine KNIB AND NOZZLE ASSEMBLY The Knib and nozzle assembly is located inside the paint tank of the machine and...
- Page 5 The knib and nozzle assembly can be fitted to the central post at the front of the machine or to either side of the front axle. Front mounted knib and nozzle assembly 1. Fit the knib and nozzle assembly onto the tapered stem at the front of the machine.
- Page 6 Side Mounting your Knib 1. Remove the R clip from the required side of the knib. (Fig 5) 2. Fit the pivot bar of the knib over the axle and align the holes. Refit the R clup to secure the knib to the axle. 3.
- Page 7 1. Shake the drum of paint thoroughly and place onto the machine so the lid of the drum is closest to the handlebars. 2. Unscrew the lid of the drum 3. Insert the Kombi Ranger draw hose into the drum and screw into the drum.
- Page 8 Flow return tap The Kombi Ranger line marker is fitted with a flow return tap, this can be used for mixing concentrates and bleeding air from the system. To operate the flow return system, proceed as follows: 1. Ensure the paint/water changeover valve is in the ‘paint’ position (lever pointing forward) (Fig 11) 2.
- Page 9 Setting the line width The line width is determined by the width between the guide discs and the nozzle height. Both must be adjusted correctly to obtain a good line with the optimum paint usage. A ruler is located in the nozzle post for measuring the line width and the nozzle height.
- Page 10 If necessary adjust the nozzle height. Turn off the pump (Fig 14) 4. Close the bonnet. Ensure the blue coiled hose is arranged with no kinks and is not fouling on the guide discs. The Kombi Ranger line marker is now ready for line marking.
- Page 11 LINE MARKING WITH YOUR KOMBI RANGER LINE MARKER WARNING HIGH PRESSURE - THE KOMBI RANGER LINE MARKER HAS A WORKING PRESSURE OF UP TO 80psi. DO NOT OPEN ANY PIPE JOINTS WHILST THE PUMP IS OPERATING. Setting the pressure The pressure of the spray can be adjusted for different applications by turning the pressure adjustment knob clockwise/anticlockwise on the control panel.
- Page 12 Marking Circles An eyelet is located on the chassis (left hand side) to aid marking circles. This can be used with a string or chain line located off a central point al- lowing the machine to maneuver in a uniform circle (Fig 16). FLUSHING AND CLEANING IMPORTANT: When cleaning./flushing the Kombi Orange line marker, ensure that water courses are not contaminated with paint.
- Page 13 Full System flush (weekly) It is not recommended to store paint in the machine for longer than 24hrs Ensure that the water tank has sufficient water for the cleaning operation. Position the machine where it can be flushed and cleaned. With the supplied clean drum, fill with clean water and add Kombi Klean.
- Page 14 The cleaner can be used with a wide variety of Fleet machine parts including nozzles, filters, pipework and couplings, returning them to an almost new condition without any damage.
- Page 15 2. Using the spring collars, slide the line guide discs in, so that they support the nozzle assembly centrally. 3. Loosen knib retainer clip and lift the knib from the tapered post. 4. Park the knib onto the bonnet horn. 5. The Kombi Ranger line marker is now ready for transportation and/or storage.
- Page 16 TROUBLESHOOTING If the Kombi Ranger line marker is not producing the perfect line, the table below is to help diagnose and remedy simple issues. The main cause for failure is inadequate cleaning/flushing. It is imperative to keep the paint system free from dried paint particles.
- Page 17 Quick Connectors Removal 1. To release a pipe from a quick connector, push on both sides of the blue collar. 2. With the collar pushed in, pull the pipe from the connector. Replacement 1. To replace a pipe into a quick connector, simply push in the pipe. The pipe should be inserted 15mm to ensure a good connection.
- Page 18 KOMBCOMP1028 UNIVCOMP9038 UNIVCOMP9013 UNIVCOMP9009 KOMBCOMP1029 Diagrams PART NO PART NAME KOMBCOMP1028 Handle Bar Top Section KOMBCOMP1029 Handle Bar Bottom Section KOMBCONS1003 M6 x 25 Socket Cap Head Screw UNIVCOMP9009 M6 Thumb Screw (Not shown) UNIVCOMP9013 Rubber Handle Grips UNIVCOMP9038 Bar Ends (Pair) UNIVCONS9058 M6 x 20 Flat Repair Washer (Not Shown)
- Page 19 KI00COMP5058 KICOCOMP6017 UNIVCOMP9058 KOMBCOMP1033 UNIVCOMP9113 KOMBCOMP1037 KOMBCOMP1233 KOMBCONS1017 UNIVCOMP5555 PART NO PART NAME UNIVCOMP5555 Wheel & Solid foam tyre KI00COMP5058 Bonnet Hinge (Sprung) KICOCOMP6017 Bonnet Horn KOMBCOMP1233 Tapered Stem KOMCOMP1033 Bonnet KOMBCOMP1037 2 Inch vented water cap KOMBCONS1017 15mm Retaining Clip for Knib UNIVCONS9058 M6 x 20 Flat Repair Washer UNIVCONS9113...
- Page 20 UNIVCOMP8541 UNIVCOMP9056 KIC00COMP5098 UNIVCOMP9005 UNIVCOMP9115 KI00COMP5071 UNIVCOMP1055 KOMBCOMP1041 UNIVCOMP9113 UNIVCOMP8521 UNIVCOMP9112 KOMBCOMP1046 PART NO PART NAME KI00COMP5071 Y Shaped Connector 8mm UNIVCOMP8521 Bowl Filter Complete KI00COMP5098 Push Fit Hand Valve KOMBCOMP1046 1/4 BSP Male Thread Female Coupler KOMBCOMP1041 Paint Water Tap 3 Way UNIVCOMP1055 1/4 BSPT M—1/4 BSP F Brass UNIVCOMP9005...
- Page 21 KOMBCOMP1023 UNIVCOMP9250 UNIVCOMP6020 UNIVCOMP9252 UNIVCONS9067 UNIVCONS9058 UNIVFINPUMP5 UNIVCONS9058 UNIVCONS9106 PART NO PART NAME KOMBCOMP1000 Kombi Ranger Control Panel KOMBCOMP1023 Coiled Mains Cable UNIVCOMP6020 Docking Battery UNIVCOMP6022 Battery Charging Station UNIVFINPUMP5 Diaphragm Pump KOMBCOMP1226 Charge Socket UNIVCONS9058 M6 x 20 Flat Repair Washer...
- Page 22 KI00COMP1195 KI00COMP5044 UNI- KOMBCOMP1210 UNIVCOMP9007 KOMBCOMP1196 UNIVCOMP8541 KI00COMP1198 KOMBCONS1004 KOMBCOMP1020 KOMBCONS1015 KOMBCONS1013 KI00COMP5041 KI00COMP5040 UNIVFINP1000 UNIVCOMP5040 UNIVCOMP5037 PART NO PART NAME UNIVCOMP5037 Guide Disc Enclosed Bearing KI00COMP5040 Spring Collar KI00COMP5041 Metal Guide Arms Set (Left & Right) KI00COMP5044 Ruler Assembly KI00CONS7012 M5 Hex Full Nut KOMBCOMP1020...
- Page 23 Specification Machine Length: 127cm Width: 74cm Height: 109cm Net Weight: 27kg 127cm 74cm Package Length: 77cm Width: 64cm Height: 57cm Net Weight: 29kg...
- Page 24 The Kombi is not guaranteed against normal wear and tear This guarantee does not interfere with the customer’s statutory rights. The pump is guaranteed for 12 months when using Fleet paint. Machine must be registered by filling in the warranty card Please fill out the table below for quick reference should you require.