1. Manuals
  2. Brands
  3. Nice Manuals
  4. Enclosure
  5. CBOX1050
  6. Installation and programming manual

Nice CBOX1050 Installation And Programming Manual

Control enclosure with control board
Hide thumbs Also See for CBOX1050:
Table of Contents

Advertisement

Quick Links

CBOX1050
CBOX with
1050 Control Board
Control enclosure
EN - Installation and programming manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CBOX1050 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Nice CBOX1050

Summary of Contents for Nice CBOX1050

  • Page 1 CBOX1050 CBOX with 1050 Control Board Control enclosure EN - Installation and programming manual...

  • Page 2: Table Of Contents

    CBOX1050 Installation and Programming Manual CONTENTS 1: 1050 CONTROL BOX OVERVIEW ..3 1050 CONTROL BOARD FEATURES ..3 2: 1050 CONTROL BOX PARTS ID...4 3: UL325 USAGE CLASSES .......5 4: 120VAC ELECTRICAL SAFETY .....13 WIRE GAUGE REQUIREMENTS ....13 5: INSTALLATION SAFETY ......1 4 6: TOOLS &...

  • Page 3: 1: 1050 Control Box Overview

    Qualified Nice | HySecurity distributors are experienced and trained to assist in resolving installation problems. For the name of a qualified distributor near you, call Nice | HySecurity at 800-321-9947. *Before contacting your distributor or Nice | HySecurity Technical Support, obtain the serial number of your operator.

  • Page 4: 2: 1050 Control Box Parts Id

    (P/N 911) CBOX1050 Control Box with 1050 Control Board OXIBD/A Multi-Channel Plug-in Receiver (P/N MX4257) ABF/A Antenna for Multi-Channel Plug-in Receiver (P/N CBOX1050) 273C Gate Warning Signs (UL Requirement) (P/N OXIBD/A) 75500019 Cable Ties (for Warning Signs) (P/N 75500019) Audio Alarm (UL Requirement)

  • Page 5: 3: Ul325 Usage Classes

    CBOX1050 Installation and Programming Manual SECTION 3: SAFETY AND UL325 USAGE CLASSES SAFETY MESSAGES IMPORTANT SAFETY INSTRUCTIONS The safety messages below inform you about potential Hazards, associated with automatic gates, can hazards that can result in injury. Safety messages specifi cally...
  • Page 6 CBOX1050 Installation and Programming Manual WARNING To reduce the risk of injury or death: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Never let children operate or play with gate controls. Keep the remote control away from children. 3. Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.
  • Page 7 CBOX1050 Installation and Programming Manual VEHICULAR TRAFFIC ONLY WARNING This automatic gate operator is not designed nor is it intended for pedestrian traffi c. Vehicular gate operators must by their nature be powerful to function reliably. This power can cause injury or death. Accordingly, direct all pedestrian traffi c to a separate walk-through gate.
  • Page 8 SENSORS An existing gate latch shall be disabled when a manually  Most Nice | HySecurity gate operators are equipped with a operated gate is retrofitted with a powered gate operator. Type A, Inherent Entrapment Sensor (IES). UL 325 Safety...
  • Page 9 CBOX1050 Installation and Programming Manual EDGE SENSORS: One or more contact sensors (edge be deemed acceptable for use in a gate operator. Study sensors) shall be located at leading edge, trailing edge, and Important Safety Instructions and consider your specifi c post-mounted, both inside and outside of a sliding gate.
  • Page 10 The following sensors have been tested with Nice | HySecurity gate operators by an independent The sensors shown in the table below have been tested with Nice | HySecurity gate operators by an independent laboratory laboratory and certifi ed to comply with UL 325 7th Edition. Select sensors from this list and certifi...
  • Page 11 CBOX1050 Installation and Programming Manual ELECTRICAL SAFETY To reduce risk of fi re or injury to persons: Turn gate operator and all circuit Observe polarity between batteries and charging circuit.   breakers OFF before performing Never mix battery sizes, types, or brands. Charging circuit ...
  • Page 12 CBOX1050 Installation and Programming Manual of recycling metal and plastic. Using a metal and plastic MAINTENANCE OF GATE SYSTEMS recycling center promotes energy cost savings. To keep your automated gate system performing both safely and reliably it is important to ensure that the components of that system are functioning properly.

  • Page 13: 4: 120Vac Electrical Safety

    This ground connection will prevent dangerous currents from appearing on the metal control box, the actuator, or the gate itself. Nice recommends an 8 foot copper rod driven all the way into the ground with a copper clamp and 12ga copper wire minimum.

  • Page 14: 5: Installation Safety

    ’ The gate for which the gate operator is intended to be used should itself be installed correctly so that it is level and plumb and the gate opens easily and evenly. ’ Note that Nice swing gate systems are not intended for installation on an incline. CAUTION Disconnect power at the control panel before making any electric service power connections.

  • Page 15: 7: 1050 Control Box Install

    CBOX1050 Installation and Programming Manual SECTION 7: 1050 CONTROL BOX INSTALLATION & SETUP MOUNT CONTROL BOX Mount control box on same side as primary actuator (for dual gate systems, same side as the actuator with shorter harness) and at least six feet away from pivot arm (IMAGE 1-1).
  • Page 16 CBOX1050 Installation and Programming Manual WIRE ACTUATOR(S) TO CONTROL BOARD 1. Strip actuator wires back 1/4”-5/16” NOTICE (7-8mm) and twist. Refer to separate actuator installation 2. Remove 5-pin and 3-pin connector manual for specific instructions for wiring from the MOTOR 1 section on control the actuator to the 1050 control board.
  • Page 17 CBOX1050 Installation and Programming Manual DETERMINE BLUEBUS PHOTO EYE LOCATIONS See below for suggestions of photo eye positioning for your gate configuration. NOTICE Name designations in IMAGE 3-1 (P1, P2, etc.) are arbitrary designations used to indicate jumper settings for each photo eye location. See INSTRUCTION 4 for jumper settings.
  • Page 18 CBOX1050 Installation and Programming Manual IMPORTANT! The 1050 control board will not operate without at least one monitored and functioning safety device connected to the control board. Before power is connected to the control board, install either the BlueBUS through-beam photo eyes per the instructions below or an alternative photo eye, such as the reflective EMX NIR-50-325 photo eye (per the instructions provided separately) before attempting to apply power to the control board.
  • Page 19 CBOX1050 Installation and Programming Manual INSTALL & WIRE BLUEBUS PHOTO EYES 1. Ensure alignment between receiver and transmitter brackets (H), then affix both to selected locations with included screws (I). IMPORTANT! If using the model EPMB/A non-adjustable photo eye (H), ensure the mounting surfaces for both devices are parallel with each other to ensure accurate alignment between TX and RX.
  • Page 20 CBOX1050 Installation and Programming Manual CONNECT BLUEBUS PHOTO EYES TO BOARD Install through beam photo eye bus wires (no polarity) into 2-pin BlueBUS connector on control board (IMAGE 6-1). If an alternative photo eye is used, follow installation instructions included in the kit.

  • Page 21: Power Options And Wiring

    CBOX1050 Installation and Programming Manual POWER OPTIONS AND WIRING There are four possible configurations available to power the 1050 control board: • 12 VDC battery charged by solar panel • 12 VDC battery charged by AC-DC charger applied to battery •...
  • Page 22 CBOX1050 Installation and Programming Manual MAIN DC POWER - INPUT CONNECTIONS MAIN DC POWER INPUT CONNECTOR NOTICE This input should only used with a 10-35 VDC, (20A or larger) power supply. However, a battery is recommended as a backup. 1. To wire Main DC Power panel connector, remove it from board for wiring (IMAGE 9-1).
  • Page 23 NOTICE For 30W solar panels and above, an external regulator must be used. Nice offers a regulator (P/N SG-4) for this purpose. See INSTRUCTION 9B for installation instructions for the SG-4 regulator. MX4682 Rev. D ©2021...
  • Page 24 Solar panels of 30W and above must be connected to a regulator which, in turn, then connects to the battery to enable battery charging. Nice offers a regulator (P/N SG-4) for this purpose. For regulators sourced elsewhere, follow the manufacturers instructions when installing. Install and wire the 30W and above solar panels and SG-4 regulator as follows: 1.
  • Page 25 (Open or Close) indicating the board is ready to ‘learn” the gate limits, and you may proceed to INSTRUCTION 12. 8. If safety devices provided in the kit are determined to be defective, contact Nice technical support. MX4682 Rev. D ©2021...

  • Page 26: Gate Limit Learning Procedure

    CBOX1050 Installation and Programming Manual 7.2 GATE LIMIT LEARNING PROCEDURE NOTICE Until the control board has “LEARNED” the open/close limits, the OPEN and CLOSE buttons must be pressed and HELD DOWN to operate the gate(s). Once limits are learned by the control board, it will take only a single press (and release) to fully open or close the gate.
  • Page 27 CBOX1050 Installation and Programming Manual 12: GATE LIMIT LEARNING PROCEDURE (CONT.) 8. Press OPEN or CLOSE buttons on the control board till gate is in approximately the halfway position. 9. If dual gate system, unplug the first actuator, plug in the second actuator and repeat Steps 3-5.
  • Page 28 CBOX1050 Installation and Programming Manual SELECT CONTROL BOARD STANDBY MODE IMPORTANT! NOTICE For SOLAR APPLICATIONS - Turn the Standby Mode ON. ’ When display is OFF In Standby Mode only a “heartbeat” will be present STANDBY MODE puts the board into a “Low Power Consumption at the OK LED.
  • Page 29 CBOX1050 Installation and Programming Manual BLUEBUS PHOTO EYE STATUS & TROUBLESHOOTING Once BlueBUS photo eyes are recognized by the control board, the photo eye LED behavior should be checked and adjustments made as follows: 1. After power up and all BlueBUS devices are recognized, observe LED behavior in each photo eye.
  • Page 30 CBOX1050 Installation and Programming Manual BLUEBUS PHOTO EYE ALIGNMENT If adjustment of photo eye alignment is necessary, refer to the following instructions: NOTICE ’ Photo eye testing is described in INSTRUCTION 16. ’ Adjustment instructions apply only to EPMOB/A and EPLOB/A models. EPMB/A model is not adjustable, and must be adjusted using mechanical means left up to the installer.
  • Page 31 CBOX1050 Installation and Programming Manual BLUEBUS PHOTO EYE TESTING Photo eyes must be tested after power is applied to the control board to ensure proper operation: 1. Apply power to control board and ensure BlueBUS devices are detected and functioning.
  • Page 32 CBOX1050 Installation and Programming Manual INSTALLING THE AUDIO ALARM IMPORTANT! The installer MUST connect the included audio alarm per these instructions. Installing the audio alarm is REQUIRED for UL325 compliance. The audio alarm (siren) included in the kit must be connected to the 1050 control board to provide an audible alarm to indicate a hard shutdown of the system, which is triggered by two consecutive entrapment events.
  • Page 33 LED lights up on the top of the receiver, then release the button. Within 10 seconds, press and hold any key on the Nice remote control until the LED in the Nice receiver blinks green 3 times, indicating that the remote control is programmed to control the receiver.
  • Page 34 Press and hold the button on the side of the Nice receiver (on 1050 board) until the LED on the Nice receiver illuminates green and keep the button pressed. The LED will illuminate after approximately 4 seconds.

  • Page 35: 8: Programming And Controls

    CBOX1050 Installation and Programming Manual SECTION 8: PROGRAMMING AND CONTROLS This section describes the navigation, menu, and programming controls for the 1050 control board. See FIGURE 8-1 (below) and TABLE 22-1 (next page) for identification of the controls used to navigate and select various options, and the following pages for descriptions and diagrams of menus and the options available for programming.
  • Page 36 CBOX1050 Installation and Programming Manual CONTROL BOARD MENU NAVIGATION Refer to FIGURE 22-1 on previous page for image of 1050 control board layout, LED indicators, and controls. Menus and parameters are accessed and selected by pressing the buttons on the 1050 control...
  • Page 37 CBOX1050 Installation and Programming Manual FORCE Button FORCE BUTTON MENU: Amount of force needed to cause the gate to stop FORCE and reverse when hitting an obstacle. (min-max FORCE sensitivity) • STATIC: Set sensitivity to constant force on a 1.Static scale of 1 to 10 (1 being the most sensitive).
  • Page 38 CBOX1050 Installation and Programming Manual DELAY Button DELAY 90 SEC. DELAY 1. Auto Close :0.0 0 SEC. Press 5 SEC. DELAY 2. Secondary :0.0 0 SEC. 5 SEC. DELAY 3. Lamp :0.0 0 SEC. 5 SEC. DELAY 4. Lock :5.0 0 SEC.
  • Page 39 CBOX1050 Installation and Programming Manual FUNCTION Button > Learn GATE WEIGHT TABLE LEARN Results Heavy in quicker acceleration/ deceleration, lower (more Light LEARN sensitive) Average FORCE settings, and higher SLOWDOWN speed. LEARN LEARN Recommended Swing Light for best reliability Medium...
  • Page 40 CBOX1050 Installation and Programming Manual FUNCTION Button > Positions F U N C T I O N S > P O S I T I O N S MENU: 100% Sets points in the gate open, close, and SlowDown partial cycles at which deceleration...
  • Page 41 CBOX1050 Installation and Programming Manual FUNCTION Button > Auxiliary IO (Cont.) FUNCTION>AUXILIARY OUTPUTS MENU: FUNCTION>AUXILIARY INPUTS MENU: Auxiliary outputs OUT1 (1,2,3,) and OUT2 (4,5,6,) can The auxiliary inputs IN1(16) and IN2 (18) can be be programmed with one of these options.
  • Page 42 CBOX1050 Installation and Programming Manual FUNCTION Button > Radio Ch. CH3 - CH15 Togle&Latch Hold to open Step H Stop Cls&Unlock Partial 1 3. Auxiliary IO Radio Ch Opn&Unlock Partial (see previous page) Close&Lock Step Step Close Open&Lock Open Unlock...
  • Page 43 CBOX1050 Installation and Programming Manual FUNCTION Button > Timers FUNCTION>TIMERS MENU: Set time for count down timers Timer 1 and Timer 2. Settings for between 1 second and 9 hours in 1 second increments. Timer 2 Second Timer 2 Minute...
  • Page 44 CBOX1050 Installation and Programming Manual FUNCTION Button / Events NOTICE See INSTRUCTIONS 23 and 24 (next page) for specific instructions Wed-Sun for programming and suspending events. TOGGLE Tue Off (blinking) ON/OFF TOGGLE Mon Off (blinking) ON/OFF Minute 0 (blinking) EV3-EV8...
  • Page 45 CBOX1050 Installation and Programming Manual 1050 EVENT PROGRAMMING INSTRUCTIONS To PROGRAM weekly events EV1 through EV8, perform the following steps: 1. Ensure time and date are set correctly. See Function/Display Menu for how to set time/date. 2. Press FUNCTION > Events.
  • Page 46 CBOX1050 Installation and Programming Manual FUNCTION Button / Charger 6. Events (see previous page) FUNCTION Charger 7. Charger 8. Standby (see below) FUNCTION>CHARGER MENU: Built-in battery charger is for use with backup battery. Charger may be manually programmed for customized charge settings or set to “Auto”...
  • Page 47 CBOX1050 Installation and Programming Manual FUNCTION Button / Adv. Settings 8. Standby (see previous page -> Com Motor Direction Com Motor Direction FUNCTION -> -> 9. Adv. Settings (blinking) <- Auto Close Opt. Auto Close Opt. 10. Default (see next page) (blinking) FUNCTION>ADVANCE SETTINGS...
  • Page 48 CBOX1050 Installation and Programming Manual FUNCTION Button / Adv. Settings (Cont.) From Inputs 10K Res. (see previous page) Both UL Input Open 10K Res. 10K Res Both (blinking) Close UL Input Digital NO (blink) UL Input Digital Digital NO (blinking)
  • Page 49 CBOX1050 Installation and Programming Manual FUNCTION Button / Defaults 9. Adv. Settings (see previous page) System Set Default to Defaults FUNCTION 10. Default System Radio Chan. Set 11. Gate Sync Default to Defaults (see next page) Radio Ch FUNCTION>DEFAULT MENU:...
  • Page 50 CBOX1050 Installation and Programming Manual DISPLAY Button: For selecting certain information for viewing in the LCD display. Display PRESS DISPLAY 1. ESC DISPLAY BUTTON MENU: DISPLAY HW: UB.01.1 2. Info 01.06.15 Info: Displays hardware and software ver- sions Clock: Displays the calendar date and time in the real time clock.
  • Page 51 CBOX1050 Installation and Programming Manual DISPLAY Button (Cont.): Continued from last page DISPLAY BUTTON MENU (CONT.): DISPLAY SUN VOLT Sun Volt: Displays the solar panel input voltage 6. Sun Volt 24.6V in volts DC. Motor Volt: Displays the voltage at the motor in volts DC.

  • Page 52: Error Messages

    CBOX1050 Installation and Programming Manual CONTROL BOARD ERROR MESSAGES & TROUBLESHOOTING CONTROL BOARD ERROR MESSAGES AND TROUBLESHOOTING DISPLAY REASON POSSIBLE CAUSE(S) Actuator connected to Motor 1 has a brief current Check for obstruction in gate path or degraded gate Dynamic M1 spike and tripped Type A sensor.

  • Page 53: 9: 1050 Accessory Connections

    CBOX1050 Installation and Programming Manual SECTION 9: 1050 ACCESSORY CONNECTIONS This section describes the accessory functions, connections, and wiring for the 1050 control board. See IMAGE 9-1(below) for a visual representation of all the accessory inputs and outputs, and the following pages for a description of I/O functions and pin designations.

  • Page 54: Output Connectors

    CBOX1050 Installation and Programming Manual 9.1 OUTPUT CONNECTORS OUT 1 / OUT 2 (1-6): Individual, isolated relays provide dry contacts for switching accessories based on programming of the “Auxiliary IO” function. These outputs are programmed in the “FUNCTION / Auxiliary I/O” menu.
  • Page 55 CBOX1050 Installation and Programming Manual LAMP (12-13): • Provides fused power (1.85A max) to drive a flashing warning lamp to indicate gate operation. • This output is active when the gate is operating (Opening and Closing). • Lamp Delay sets the amount of time the lamp accessory output is activated prior to gate movement. Settings from 0 to 5 seconds with a step of 0.5 seconds.

  • Page 56: Input Connectors

    CBOX1050 Installation and Programming Manual 9.2 INPUT CONNECTORS AUXILIARY INPUTS 1 & 2 (16-19): • These digital inputs may be connected to the digital outputs of accessories and programmed to activate or control the gate operator in a number of different modes.
  • Page 57 CBOX1050 Installation and Programming Manual EDGE INPUT (28-29): • The EDGE input may be configured as a monitored ANALOG input, or DIGITAL (NC or NO) input. • The EDGE sensor input is intended for ANSI/UL 325 listed gate edge sensors to protect against entrapment and hazardous pinch points along the moving edge of the closing gate.
  • Page 58 CBOX1050 Installation and Programming Manual GUARD STATION INPUT (34-37): • With the Guard Station switches installed, the user can operate the gate by pushing the respective buttons for the command that is desired. • Gate Open and Close are controlled by NORMALLY OPEN (NO) and Stop is controlled by NORMALLY CLOSED (NC) momentary switches.

  • Page 59: Emergency Vehicle Access

    CBOX1050 Installation and Programming Manual 9.3 EMERGENCY VEHICLE ACCESS The automatic vehicular gate system must be designed to allow access to emergency vehicles under different operating conditions. Read all the following information. Make sure that your gate operating system is compliant with all local codes and regulations and that access for emergency vehicles is assured.

  • Page 60: Communications Bus

    • The Oview controller is an optional programming and diagnostic tool, which plugs directly into the 1050 control board using an RJ45 network cable and is part of the Nice “Opera” control system. • The Oview controller can be used in “stand-alone” mode via its front-panel keypad, or it may be accessed via a Bluetooth-enabled PC when used with the optional OVBT module and Oview Software Suite.

  • Page 61: 10: Appendix

    CBOX1050 Installation and Programming Manual SECTION 10: APPENDIX 10.1 CALCULATING SOLAR REQUIREMENTS CALCULATING SOLAR REQUIREMENTS 1. Estimate the gate traffic measured in open/close cycles per TABLE 25-1. TABLE 25-1: SOLAR PANEL WATT/CYCLE CHART DAILY CYCLES 1-10 1-20 1-40 1-60 1-80 80+...

  • Page 62: Maintenance Schedule

    CBOX1050 Installation and Programming Manual 10.2 MAINTENANCE SCHEDULE MAINTENANCE SCHEDULE Component Maintenance Action Months Annually Activate the primary (inherent) reverse system by blocking the gate with a solid object. The gate ALARM should reverse momentarily then stop. Restart the gate and block again with a solid object. The gate should reverse momentarily, then stop, and go into hard shutdown with an alarm.

  • Page 63: System Troubleshooting

    Check accessory inputs and clear them as necessary. Also check to ensure the Gate opens by itself. Event programming has not been set to open the gate at a particular time. 1050 display shows repeated “Nice Apollo Check battery voltage and replace if necessary (Display>Battery Volt).

  • Page 64: Installation Checklist

    CBOX1050 Installation and Programming Manual 10.4 INSTALLATION CHECKLIST • The installer and customer must each ensure that all of the following actions have been completed. • Left box is for installer check off and the right box is for customer check off.

  • Page 65: Part Drawings

    CBOX1050 Installation and Programming Manual 10.5 PART DRAWINGS Box, Control, CBOX or 11111B Board, Control, 1050 Lid, CBOX or 11111B Switch, Push Button, Control Box Tab, 11111B, 11111C KeySwitch, Receiver, OXIBD/A, Single Pole Multi-channel This drawing is a representation and should be used for parts reference only.
  • Page 66 CBOX1050 Installation and Programming Manual support.hysecurity.com...

  • Page 67: Warranty

    This warranty will be interpreted, construed, and enforced in all respects in the name plate of a manufacturer other than HySecurity or Nice and they are not a accordance with the laws of the State of Washington, without reference to its part of the base model.
  • Page 68 CBOX1050 Installation and Programming Manual (This page intentionally blank) support.hysecurity.com...
  • Page 69 Qualified Nice | HySecurity distributors are experienced and trained to assist in resolving installation problems. For the name of a qualified distributor near you, call Nice | HySecurity at 800-321-9947. *Before contacting your distributor or Nice | HySecurity Technical Support, obtain the serial number of your operator.
  • Page 70 Nice North America | HySecurity Gate & Barrier Division 6705 S 209th St, Ste 101 Kent, WA 98032 hysecurity.com...

Table of Contents

Save PDF