WEIHONG Ncstudio Phoenix Manual

Wood three-axis engraving system

Table of Contents

Quick Links

Manufacturer's Manual of Ncstudio Phoenix

Wood Three-Axis Engraving System

1 System Introduction .......................................................................................................... 1

1.1 Overview .................................................................................................................... 1

1.2 Hardware Connection Diagram .................................................................................. 1

1.3 Software Interface ...................................................................................................... 2

1.3.1 NcConfig .............................................................................................................. 2

1.3.2 NcTune ................................................................................................................ 3

1.3.3 NcStudio .............................................................................................................. 4

2 Wiring ................................................................................................................................ 9

2.1 Hardware .................................................................................................................... 9

2.1.1 NC60A ................................................................................................................. 9

2.1.2 Lambda Controller ............................................................................................... 9

2.1.3 EX31A ............................................................................................................... 10

2.2 Operation Panel Ports .............................................................................................. 13

2.3 Signal Type .............................................................................................................. 13

2.3.1 Switch Value Input Signal .................................................................................. 14

2.3.2 Relay Output Signal ........................................................................................... 14

2.3.3 Relay Output Signal ........................................................................................... 14

2.3.4 Command Pulse Signal ..................................................................................... 15

3 Machine Debugging ........................................................................................................ 16

3.1 Overview .................................................................................................................. 16

3.2 Install the Software ................................................................................................... 16

3.3 Modify I/O Port Polarity ............................................................................................ 16

3.4 Set Debugging Parameters ...................................................................................... 17

3.5 Check Axis Direction ................................................................................................ 18

3.6 Go to Mechanical Origin or Set Datum ..................................................................... 19

3.6.1 Making Axes Go to Mechanical Origin ............................................................... 19

3.6.2 Setting Datum .................................................................................................... 21

3.7 Set Workpiece Origin ............................................................................................... 21

3.7.1 Clearing ............................................................................................................. 21

3.7.2 Centering ........................................................................................................... 22

3.7.3 Setting Workpiece Offset and Public Offset ....................................................... 23

3.7.4 Tool Calibration .................................................................................................. 23

3.7.5 Setting Tool Compensation Parameters ............................................................ 26

4 Quick Start ...................................................................................................................... 27

4.1 Overview .................................................................................................................. 27

4.2 Loading a Machining File ......................................................................................... 27

4.3 Running Simulation .................................................................................................. 27

Version: 2021.12.01 1st Version

Author: Product Testing Department

Contents

上海维宏电子科技股份有限公司

SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.

Table of Contents

Need help?

Do you have a question about the Ncstudio Phoenix and is the answer not in the manual?

Questions and answers

Summary of Contents for WEIHONG Ncstudio Phoenix

Page 1: Table Of Contents
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Manufacturer's Manual of Ncstudio Phoenix Wood Three-Axis Engraving System Version: 2021.12.01 1st Version Author: Product Testing Department Weihong Corporation All Rights Reserved Contents 1 System Introduction ......................1 1.1 Overview ........................1 1.2 Hardware Connection Diagram .................. 1 1.3 Software Interface ......................
Page 2 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4.4 Starting Machining ....................28 5 Program-related Functions ..................... 29 5.1 Program Management ....................29 5.1.1 Loading a Program .................... 29 5.1.2 Unloading a Program ..................29 5.1.3 Creating, Editing, Deleting and Renaming a Program ........29 5.2 Machining Wizard .....................
Page 3 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.5 Dual-Y Axis Jiggle ....................56 10.6 Calibration ......................57 10.7 Going to Workpiece Origin ..................57 10.8 Going to Fixed Point ....................58 10.9 MDI ......................... 58 10.10 Clearing Drive Alarms ..................58 10.11 Reconnecting to the Controller ................
Page 4: System Introduction
 EX series terminal board: EX31A For the hardware connection diagram, see section 1.2 Hardware Connection Diagram. Software For introduction of the NcStudio Phoenix Three-axis Engraving System software interface, see section 1.3 Software Interface. 1.2 Hardware Connection Diagram Hardware connection method varies based on the control system type. Example of a non- bus control system and a bus control system using NC60A are shown below.
Page 5: Software Interface
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1.3 Software Interface This section gives you a brief introduction of the software interface of the NcStudio Phoenix Three-axis Engraving System. 1.3.1 NcConfig The homepage of NcConfig is shown below: 2 / 61...
Page 6: Nctune
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1. Menu bar 2. Function area 3. Project configuration area 1.3.1.1 Function Area Target functions are selected in the project configuration area and debugged in the function area. 1.3.1.2 Project Configuration Area Click the Project or Configuration tab in the project configuration area's lower part to use different functions (If the Project tab is not displayed in this area, go to View >...
Page 7: Ncstudio
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1. Menu bar 2. Status bar 3. Welcome page 1.3.3 NcStudio The homepage of NcStudio is shown below: 4 / 61...
Page 8 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1. Menu bar 2. Status bar 3. Axis coordinate area 4. Override setting area 5. Machining information area 6. Function window 7. Operation mode area 8. Operation button bar 1.3.3.1 Menu Bar You can access the following functions in the menu bar: ...
Page 9 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Data Backup, NcTune, Remote Assistance, NcCloud, M Instruction Table, and About 1.3.3.2 Status Bar You can access the following functions in the status bar:  System modes: Auto, Manual, and Homing  System status: Idle, running, paused, or emergency stop.
Page 10 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. It shows the current machining progress, current program line number, machining duration and current tool number. 1.3.3.6 Function Window Click the following tabs in the function window to access different functions:  Track: Displays the machining or dry running track.
Page 11 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. and turn the handwheel knob by a certain degree to make the target axis move in the target direction.  Stepping: Select 0.01, 0.05, 0.1, 0.5, 1, 5, or 10 (the unit is mm), or enter a value in the blank field.
Page 12: Wiring
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2 Wiring This section gives you a brief introduction of the signal types supported by the NcStudio Phoenix Three-axis Engraving System and the port definition. 2.1 Hardware This section gives introduction of the following hardware: ...
Page 13: Ex31A
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Definitions for Lambda 21B and Lambda 21A ports are basically the same; therefore, the following content introduces port definitions for the Lambda 21B controller as an example. Multiple EX31A extension terminal boards can be connected to the Lambda 21B controller to meet your needs.
Page 14 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.  EX35A: Supports 32-channel output  EX36A: Supports 32-channel input Port definitions of the Lambda 21B connected to two EX35A terminal boards and one EX36A terminal board are shown below as an example:...
Page 15 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 12 / 61...
Page 16: Operation Panel Ports
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2.2 Operation Panel Ports Descriptions of the operation panel ports are shown below:  +5V: Provides power supply for the operation panel.  Tx_N: Sends differential signal.  NC: Needs no wire connection.
Page 17: Switch Value Input Signal
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.  Analog Output Signal  Command Pulse Signal 2.3.1 Switch Value Input Signal The switch value input signal supports active high and active low:  Connecting to the COM port in NO mode means to receive signal.
Page 18: Command Pulse Signal
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. The figure is as follows: 2.3.4 Command Pulse Signal Pulse commands that control the controller's motion consist of pulse + direction, negative logic, as shown below. The maximum pulse frequency is 1MHz. 15 / 61...
Page 19: Machine Debugging
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3 Machine Debugging 3.1 Overview This section gives you a brief introduction of the basic debugging process for the NcStudio Phoenix Three-axis Engraving System. The debugging process is shown below: If the manufacturer's password is required during debugging, contact the manufacturer.
Page 20: Set Debugging Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. The relationship between the signal status and the port symbols is shown below:  Input port: no signal is detected; signal is detected  Output port: no signal is detected; signal is detected Follow the steps below to modify the I/O port polarity: 1.
Page 21: Check Axis Direction
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. In the Param window, click the Operator pull-down menu in the left column and select Manufacturer. 3. Set the following parameters: o Encoder Direction: Indicates the direction of the axis encoders. 1: positive direction;...
Page 22: Go To Mechanical Origin Or Set Datum
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3. In the Param window, click the Operator pull-down menu in the left column and select Manufacturer. 4. Check the Axis Direction(X) value. o 1: positive direction o -1: negative direction 5. In Manual mode, click the X+ button to move the X axis. Check to see if the X axis moves in the positive direction as determined by the right-hand rule.
Page 23 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Select one from the following methods to make the axes go to the mechanical origin:  In Homing mode, click X Homing/Y Homing/Z Homing in the operation button bar to make the X/Y/Z axis go to the mechanical origin. You can also click All Homing to make all the axes to the mechanical origin in the sequence of Z axis, X axis and Y axis.
Page 24: Setting Datum
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. After an axis has gone to the mechanical origin, the icon will be displayed before the axis in the axis coordinate area. 3.6.2 Setting Datum If an absolute encoder is used, you can directly set the encoder zero conveniently without having to make the axes go to the mechanical origin.
Page 25: Centering
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Click Yes. The X-axis workpiece coordinate of the current point becomes 0. 3.7.2 Centering Two types of centering are supported: line centering and circle centering. Line centering is mostly used to locate the center of regular rectangle work pieces while circle centering circular work pieces.
Page 26: Setting Workpiece Offset And Public Offset
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. mechanical coordinate based on the X-axis mechanical coordinate of the current point and the X-axis mechanical coordinate recorded in the last step, and sets the X-axis workpiece coordinate of the midpoint to zero.
Page 27 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. Set Setting in the upper left corner to ON. 3. In the Basic Setting area, click the Active Tool pull-down menu, select the target tool number, and set the following parameters: o Positioning Times: Indicates the times of fine positioning when approaching the tool sensor during tool calibration.
Page 28 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. In the Calibration Mode area of the Calibration tab, select one method:  Automatic measuring: Click Auto Measure. The system carries out fixed calibration automatically. The process of automatic fixed calibration is shown below: ...
Page 29: Setting Tool Compensation Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3.7.4.3 Mobile Calibration During mobile calibration, the Z-axis workpiece coordinate is automatically cleared. Only workpiece offset of the current workpiece coordinate system will be changed. Before executing mobile calibration, ensure that:  Set the manufacturer parameter Tool Calibration Type to 1.
Page 30: Quick Start
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4 Quick Start 4.1 Overview This section gives you an introduction of a simple machining process with the NcStudio Phoenix Three-axis Engraving System: 4.2 Loading a Machining File Before starting machining, you need to load the machining program first.
Page 31: Starting Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 4.4 Starting Machining Select one from the following methods to start machining:  Press the F9 key.  In the operation button bar, click  In the menu bar, go to Machine > Cycle Start.
Page 32: Program-Related Functions
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 5 Program-related Functions 5.1 Program Management You can create, load, unload, edit, delete, and rename a program in the software. 5.1.1 Loading a Program Select one from the following methods to load a machining program: ...
Page 33: Single Block Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. Select a tab and set the parameters based on the left figure. 3. Click Execute. The system starts machining. 5.3 Single Block Machining In this mode, the program commands will be executed line by line for you to check the machine movement.
Page 34: Eng Tool And Line Selection
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. o In Auto mode, click Selective MC in the operation button bar. o In the menu bar, go to Advanced > Selective Machining. 2. Enter target values in the Start Row and End Row fields.
Page 35 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. To specify the tool, set Select No. to ON. A selection box column will be displayed before the tool number column. Tick the target tool number. To modify a tool number, set Modify No. to ON. The Modify No. column will be...
Page 36: Advanced Machining
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Double-click the target field in the Modify No. column and enter the target tool number. Click Confirm. 3. In the Choose line processing area, enter values in the Start Row and End Row fields.
Page 37: Rotation And Mirroring
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. In the Array area, click the Array Mode pull-down menu and select Rectangular. The array mode is set to Convention by default, which means does not enable array. 3. Enter the number of rows and columns, row interval, and column interval in the Rows, Columns, Row Space R, and Column Space C fields.
Page 38: Machining Cycle
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. In the Mirror & Rotate area, click the Machining Mode pull-down menu and select an option: o To rotate the path: a. Select CW 90° /CW 180° /CCW 90° . b. Enter the rotation center X and Y coordinates in the Rotate Center X and Rotate Center Y fields.
Page 39 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. Enter the target cycle times and interval in the Cycles and Interval fields. The current times of machining will be displayed after Cycle Index. 36 / 61...
Page 40: Check Machining Information And Statistics
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 6 Check Machining Information and Statistics You can check the machining information automatically collected by the system to formulate machining plans and avoid possible problems. Follow the steps below to check the machining information/statistics: In the menu bar, go to Program >...
Page 41 上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 38 / 61...
Page 42: System Settings
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 7 System Settings 7.1 Viewing and Setting Parameters This section introduces how to set the system global parameters, drive parameters, and tool compensation parameters. 7.1.1 Global Parameters In the menu bar, go to System > Global Parameters to open the Param window: Click the Operator pull-down menu on the left side.
Page 43: Tool Compensation Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1. In the menu bar, go to System > Driver Parameters to open the Driver Param window: 2. Double-click the target field, enter the target value, and click OK. In the Driver Param window, the following functions are also supported: ...
Page 44: Adding Common Parameters
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1. In the menu bar, go to System > Tool Compensation Parameters to open the Tool Compensation dialog box: 2. Double-click the target field, enter the measured value, and click OK. 7.2 Adding Common Parameters You can set target parameters to become common parameters and displayed under the Common tab of the function window.
Page 45: Changing Password
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3. Click the first pull-down menu and select Operator or Manufacturer to display operator or manufacturer common parameters. Click the second pull-down menu and select Name, Description, or Address to determine the query condition. Enter the searching keyword in the blank field and click the searching icon.
Page 46: Switching System Language
2. Give the computer identification code and the verification code to the technical support staff for remote control. 7.7 Using NcGateway NcGateway is a component of the WEIHONG NcCloud system. It provides data interfaces and communication protocols for device Internet connection. You can use NcGateway to manage devices.
Page 47: Software Registration
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. After adding software components in NcConfig, M codes of the components will also be added. Modification is supported. 7.9 Software Registration You need to register the software if the software use period has or is about to expire, or if the writing type does not match.
Page 48: Ncconfig
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 8 NcConfig With NcConfig, you can configure Lambda controllers, terminal boards and machine parts, set port mapping and port protection to improve project efficiency. 8.1 Opening NcConfig Use the following method to open NcConfig: 1.
Page 49: Configuring Machine Parts
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 8.3 Configuring Machine Parts In NcConfig, you can select and configure the machine parts in use, such as M codes, operation panel, tool magazine, saw, double work station, clamp, and handwheel. Follow the steps below to configure machine parts: 1.
Page 50: Configure Function Buttons
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 1. In the left Configuration list, double-click MCodeConfig to open the MCodeConfig page on the right: 2. Select the target row and double-click the target MCode field to modify the M code. 8.3.2 Configure Function Buttons In NcConfig, you can add or delete function buttons in NcStudio.
Page 51: Configure The Tool Magazine
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 8.3.3 Configure the Tool Magazine The system supports tool magazines of different mechanical structures, combination of multi-cylinder single-frequency and multi-cylinder multi-frequency functions, and tool magazine selection. Tool magazine options on the Components page include: ...
Page 52: Configure Dual Drive
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. Double-click the target PhysicalAddress field to specify a physical address (controller and port) for the corresponding logical address. 8.3.5 Configure Dual Drive Follow the steps below to configure dual drive axis: 1. In the left Configuration list, double-click Distribute to open the Distribute page on the right: 2.
Page 53: Configure Clamps
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 3. Double-click the target PhysicalAddress field to specify a physical address (controller and port) for the corresponding logical address. 8.3.8 Configure Clamps Follow the steps below to configure clamps: 1. In the left Configuration list, double-click Clamp to open the Clamp page on the right: 2.
Page 54: Set Port Protection
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. Double-click the target Physical Port field to specify a physical address (controller and port) for the corresponding logical address. 3. Select one from the following methods to save the changes: o To save changes on the current page, click under the menu bar.
Page 55: Creating Multi-Configuration Installation Package
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 2. Set the Enable switch of the target port to ON. 3. Double-click the Protection Type field of the target port and select a protection type in the pull-down menu. 4. Select one from the following methods to save the changes: o To save changes on the current page, click under the menu bar.
Page 56: Nctune
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 9 NcTune NcTune includes functions that can be used during debugging instead of normal machining. Functions supported by NcTune are displayed on the welcome page, as shown below, such as setting lead screw error compensation and centering parameters, etc.
Page 57: Other Functions
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10 Other Functions 10.1 Generating Installation Package You can create a complete installation package in the current system to have a backup of the system files and a steady version of system. Follow the steps below to create an installation package: 1.
Page 58: Using Handwheel
A WEIHONG handwheel is shown below: Follow the steps below to use a WEIHONG handwheel for machining control: 1. In Auto mode, select one from the following methods to enter handwheel mode: o In the operation button bar, click HW Guide.
Page 59: Dual-Y Axis Jiggle
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.  Switch to Auto mode.  Ensure that the system is in running or paused state. Follow the steps below to jiggle the cutter: 1. In the menu bar, go to Machine >Jiggle: 2.
Page 60: Calibration
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.  To adjust the positions of the two Y axes at the same time: a. Select or enter a movement unit/step on the right side (0.01, 0.1, 1, or other values). b. Click Y- or Y+ to move the Y axes in the positive or negative direction by the selected or entered amount.
Page 61: Going To Fixed Point
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. 10.8 Going to Fixed Point You can control the axes to move to a point with specified mechanical coordinates. You can change the point mechanical coordinates by modifying the values of Fixed Point Position(X), Fixed Point Position(Y), and Fixed Point Position(Z) parameters.
Page 62: Switching Between Multi-Z Modes
上海维宏电子科技股份有限公司 SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. In the menu bar, go to Machine > Reconnect Controller. 10.12 Switching between Multi-Z Modes This function is available in software with multiple-Z axis configuration to switch between sequential movement mode and linkage movement mode.
Page 63: Legal Notices
Product. You are obliged to stop any form of illegal copying of the Software Product and accompanying materials. Weihong Company can update the Software Product at any time. You can pay real-time attention to Weihong Company's official website. 60 / 61...
Page 64: Termination
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD. Termination This license may be terminated by Weihong Company at any time once you violate any terms or conditions made in this agreement. Once the license is terminated, you are obliged to destroy all the copies of the Software Product or return them to Weihong Company.
Page 65 S P E C I A L I Z E D / C O N C E N T R A T E D / F O C U S E D Shanghai Weihong Electronic Technology Co., Ltd. Address: No. 1590, Huhang Rd., Fengxian, Shanghai, China, 201401 Hot-line: 400 882 9188 Website: www.weihong.com.cn/en...