Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Guru EVOLUX
Summary of Contents for Guru EVOLUX
- Page 1 PRODUCT GUIDE EVOLUX SYSTEM LINEAR/SQUARE DRAINAGE...
-
Page 2: Table Of Contents
» Drainage » Accessories for installation and maintenance NEW FORMATS • MORE SHOWER CONFIGURATION OPTIONS INSTALLATION EVOLUX SYSTEM • GENERAL INSTALATION PROCEDURE FOR THE EVOLUX SYSTEM • INSTALLATION WITH TEMPLATE • INSTALLATION WITH INTEGRA SYSTEM • INSTALLATION DIAGRAM RECOMENDATIONS PRODUCT DATA SHEET... -
Page 4: Description
DESCRIPTION It comprises a section of WATER-STOP waterproofing membrane, factory-sealed to a special adapter to connect to a low profile floor gully and a stainless steel shower drain and grill. • TECHNICAL, AESTHETIC AND PRACTICAL EVOLUTION Separate installation of the drain body and the waterproof membrane, which is easier and more practical. -
Page 5: Waterproofing
25 cm from the edge. • DRAIN The EVOLUX BASE set doesn’t include drain extension and cover. It must be completed with the EVOLUX shower drain and grill, which can be chosen among the different models available. -
Page 6: Drainage
DESCRIPTION • DRAINAGE Low profile trapped floor gully which complies to EN 1253, parts 1 and 2 Side outlet with DN/OD 50 connector. It can be angled through 360º 50 mm-high water seal (can be eliminated). Reducer: DN 50/40 Push fit connections with O-rings and sliding joints; not gluing. Drain body and connector: ABS ;... -
Page 7: New Formats
NEW FORMATS • MORE SHOWER CONFIGURATION OPTIONS WITH BASE 3 m WITH BASE 4 m 1,2 m 0,9 m 1,5 m 1,2 m 1,8 m 0,9 m... -
Page 8: Installation Evolux System
INSTALLATION • GENERAL INSTALLATION PROCEDURE FOR THE EVOLUX SYSTEM Prepare the shower area • Decide on the height or depth required to ensure at least 1.5 % gradient towards the drain. At the drain point, a minimum base thickness of 110 mm is required (including 3 to 25 mm tile thickness with adhesive). - Page 9 *To make up for the height when installing a very thin flooring as mosaic glass tiles, microcement or other (less than 7 mm total flooring depth) and for installing EVOLUX INTEGRA System, you must use the TEMPLATE provided. To do this, follow the instructions...
- Page 10 • Seal the joint between the flooring and the shower channel edge with W-S MASTIC or similar and position the grill. • EVOLUX INSTALLATION DIAGRAM EVOLUX System installation example with 9 mm flooring thickness Sloped cement screed WATER -STOP membrane...
-
Page 11: Installation With Template
INSTALLATION • INSTALLATION WITH TEMPLATE Make up the cement screed base Once the base has set, remove the drain protection cover and the installation Pour the cement up to the level marked template. on the protective cover, embedding the floor gully. Connect the membrane to the floor gully as indicated in the general procedure Position the installation template in the... -
Page 12: Installation With Integra System
INSTALLATION • INTEGRA SYSTEM INSTALLATION Prepare the shower area. ACCESSORIES Installation TEMPLATE (according to the model) Proceed as indicated in point 1 of the general procedure, but remember that the drain point needs a minimum height of 90 mm plus the thickness of the flooring material and adhesive. -
Page 13: Installation Diagram
The same tile adhesive can be used as that used to lay the shower flooring. • EVOLUX INTEGRA INSTALLATION DIAGRAM EVOLUX INTEGRA System installation example with 9 mm flooring thickness Sloped cement screed WATER -STOP membrane W-S MASTIC... - Page 14 INSTALLATION Detail of INTEGRA EVOLUX SYSTEM. Content according model.
-
Page 15: Recomendations
RECOMENDATIONS The outlet pipe must have a gradient of at least 1.5% towards the drain (a 1.5 to 2 cm drop every metre). The length of this section must not exceed 1 metre. The flooring must be flush with the grill so when installing the drain body, ensure that its height allows the flooring to be installed later. -
Page 16: Product Data Sheet
PRODUCT DATA SHEET PRODUCT DATA SHEET EVOLUX SYSTEM Description: Trapped floor gully with factory-sealed integrated waterproofing comprising a section of WATER-STOP membrane. Use: the construction of tiled showers for domestic or public use. Normative References: UNE EN 1253-1:2015 Manufacturer: Estil Gurú S.L.U. -
Page 17: Warranty
Estil Gurú S.L.U. as manufacture of waterproofing systems, guarantees the quality and performance of its products. The drain used in the EVOLUX system complies with EN 1253 parts 1 and 2 as it relates to the Declaration of product compliance. - Page 18 Pol. Industrial El Pla, Carrer dels Telers, 22 Tel.: 96 291 45 11 www.estilguru.com...
Need help?
Do you have a question about the EVOLUX and is the answer not in the manual?
Questions and answers