Advertisement
Quick Links
HAULMASTER 1500 &
*Pot Hauler *Drop Lines *Downrigger *Deep Dropping * Longlining*
Congratulations on your new purchase & thank you for choosing LSM!
The HAULMASTER & HAULMASTER X are a modular unit capable of hauling pots, drop
lines, down rigging, gurdy fishing, deep dropping, longlining, & more.
HAULMASTER 1500 features a single speed drive with 1500w output motor.
HAULMASTER X features a variable speed drive with 1500w output motor.
• HAULMASTER 1500 Basic & HAULMASTER X Basic include:
1. Main Unit
2. Boom
3. Folbe Sheave
(closed sheave for DD model)
4. Aluminium Boom Hook
5. Frame Post
6. Position Lock
7. Top Mount
8. Gunnel Side Mount
9. Bottom Pocket Mount
10. Bottom Floor Mount
11. Bottom Mount Spacers
12. 10Ft Twin core lead with plug
(not pictured)
13. 2 x battery lugs and heat shrink
(not pictured)
14. Spool Changeover Tool
15. All Fixing Hardware (not pictured)
16. Mount Sleeve (x2)
HAULMASTER-X
Advertisement
Summary of Contents for Lone Star Marine HAULMASTER 1500
- Page 1 The HAULMASTER & HAULMASTER X are a modular unit capable of hauling pots, drop lines, down rigging, gurdy fishing, deep dropping, longlining, & more. HAULMASTER 1500 features a single speed drive with 1500w output motor. HAULMASTER X features a variable speed drive with 1500w output motor.
- Page 2 • HAULMASTER 1500 PH & HAULMASTER-X PH – Basic plus Line Hauling Disk with Capstan, self-tailing rope catch, and tension roller • HAULMASTER 1500 DR & HAULMASTER-X DR – Basic plus fixed HD spool (no drag) for down rigging/gurdie fishing •...
-
Page 3: Installation
Installation Tools Required: Power Drill, 80mm (3 inch) hole saw, 6mm, 8mm, 10mm, 12mm drill bit (can be half a mm larger), 10mm, 13mm, 17mm, 19mm wrench, swage or other means of crimping electrical leads. Through Gunnel Assembly • Mount Top Mount (7) assembly through gunnel. If gunnel is sloped to one side pack up underside of top mount to ensure Frame Base (5) is perpendicular to the floor or pocket mount below. - Page 4 Position Lock Assembly • Drop Frame Post (5) through top mount into bottom mount ensuring frame post is resting on the bottom of the low mount *Black plastic cap should be on the bottom • Slide Position Lock (6) onto frame post ensuring locking pin is in the down position and seated in a hole.
- Page 5 Change Frame & Boom Length • Frame post can be shortened to ensure the HAULMASTER body sits at an appropriate height for your usage. • To do this, measure the distance you would like to remove from Frame Post and cut with a hacksaw.
- Page 6 • Secure with PTO clip or bolt provided. Use PTO clip if you intended to disassemble the unit between uses. Use bolts if intending to leave the unit as an assembly. • Insert Boom (2) into top collar. • Cut length if desired and repeat above process Electrical HAULMASTER is a self-contained unit with all switches, controller/solenoid, &...
- Page 7 Using the HAULMASTER • Ensure the direction knob is in the STOP (middle) position. • Plug lead into unit. • Ensure the circuit breaker is engaged by pushing the yellow paddle up. • Engage drive by pressing the power button above the circuit breaker. When the red light is on the unit is ready to use.
- Page 8 Changing Spools The HAULMASTER is a modular system and all 4 spools can be run from the same unit. • PP block & DR downrigger spool are clutch less and slide onto the shaft with no additional plate. • DD & LL spools use a clutch. This clutch plate must be installed to use. •...
-
Page 9: Maintenance
Use this product at your own risk Lone Star Marine or its distributors will not be liable in the event of damage, accident, injury, or death as the result of use, misuse or installation of this product. Lone Star Marine Pty Ltd or its distributors will not be liable in the event of damage, accident, injury, or death as the result of mechanical or electrical failure of this product.