1. Manuals
  2. Brands
  3. Cooper Atkins Manuals
  4. Transmitter
  5. EnviroTrak Sensorex TX100
  6. Installation and operating manual

Cooper Atkins EnviroTrak Sensorex TX100 Installation And Operating Manual

Ph monitoring, ph/mv 2-wire transmitter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
pH Monitoring Installation and Operating Guide
Cooper-Atkins Corporation | Accuracy to the Highest Degree
www.cooper-atkins.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EnviroTrak Sensorex TX100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Cooper Atkins EnviroTrak Sensorex TX100

  • Page 1 pH Monitoring Installation and Operating Guide Cooper-Atkins Corporation | Accuracy to the Highest Degree www.cooper-atkins.com...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS For additional mounting instructions, consult the enclosed Installation and User Manual provided in the pH Kit from Cooper-Atkins. Please feel free to contact I-Care at 888- 533-6900 x2 for assistance. Package Contents ..........................3 Hardware Mounting ..........................4 A. Mounting .............................. 4 pH Electrode - Calibration ........................5 A. Calibrating pH Electrode (7.00pH and 4.00pH) ..................5 pH Electrode – Clean Electrode Notification ..................6 A. Setting Cleaning Reminder .

  • Page 4: Package Contents

    Package Contents Contents of the pH Kit. A. pH Mounting Plates D. Analog Transmitter B. Sensorex Installation and a. Transmitter Box Operating Manual b. Analog Transmitter wired to C. Sensorex pH Monitor Sensorex pH Monitor E. pH Electrode and Cable F.

  • Page 5: Hardware Mounting

    Hardware Mounting A. MOUNTING: 1. First determine mounting location for the Sensorex pH Monitor probe. A mounted example is pictured below. 2. Locate a suitable location to mount the Sensorex pH Monitor box near an AC outlet. 3. Four different mounting brackets are supplied allowing for a wide range of mounting options.

  • Page 6: Ph Electrode - Calibration

    pH Electrode - Calibration Periodically, the pH Electrode must be calibrated. This can be done during the electrode cleaning cycle. Follow the instructions below to calibration the pH probe. REFER TO SENSOREX MANUAL PAGE 21 IF NEEDED A. CALIBRATING pH ELECTRODE (7.00pH and 4.01pH): 1) Press and hold <E>...

  • Page 7: Ph Electrode - Clean Electrode Notification

    pH Electrode – Clean Electrode Notification A reminder to clean, and if need be, calibrate your pH electrode can be set up for 1 – 250 days. Default setting is 90 days. Follow the instructions below to change the number of days between cleanings. REFER TO SENSOREX MANUAL PAGE 25 IF NEEDED A.

  • Page 8: Transmitter Setup

    Transmitter Setup Once the pH Electrode has been mounted and configured, the reset button on the Analog Transmitter must be pressed to initiate sending the newly configured pH values. 900Mhz Digital Analog Transmitter 1. Remove the Transmitter cover. 2. Verify that the Transmitter is wired (D) for 4-20mA input. 3.

  • Page 9: Software Configuration - Ph Electrode

    Software Configuration – pH Sensor In order for the transmitters that have been installed to work they must be registered in the software. There is a Transmitter ID Label on the exterior of the transmitter box, another label on the transmitter’s lid and an extra label to be placed at the monitoring point.
  • Page 10 **Note: (D) You may need to create a new formula for transmitter type Sensorex TX100-Ph Monitor if it does not appear in the drop-down. Please contact I-Care for assistance. 5. Select the sensor group you wish to assign the transmitter to from the Assign To Group (Optional**) (E) drop-down list.
  • Page 11 NOTES:...
  • Page 12 Cooper-Atkins Corporation 33 Reeds Gap Rd., Middlefield, CT 06455 www.cooper-atkins.com 27-241 V1017...

Table of Contents