Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SignalFire AI-6C
- Page 1 AI-6C Automatic Intelligent OPTICALFIBER FUSION SPLICER 2022.05...
-
Page 2: Table Of Contents
SAFETY REQUIREMENTS WARNINGS/PRECAUTIONS CHAPTER Ⅰ OPERATION KEY COMBINATION FUNCTION DISPLAY MENU INTRODUCTION INTRODUCTION TO SPLICE INTERFACE CHAPTER Ⅱ SOFTWARE DOWNLOAD SCREEN MENU FUNCTION ON/OFF CHAPTERⅢ ARC CALIBRATION CHAPTER Ⅳ FIBER STRIPPING AND PUT INTO HOLDER CHAPTER Ⅴ REPLACE ELECTRODE CHAPTER Ⅵ ACTIVATE ELECTRODE CHAPTER Ⅶ... -
Page 3: Safety Requirements
SAFETY REQUIREMENTS WARNINGS/PRECAUTIONS At any stage of operation on the optical fiber fusion splicer, you must take the following general safety AC/DC Adapter precautions. Not take these warnings and precautions or not comply with the warnings which described in this The Output Characteristics Of The Power Adapter Must Meet The Following Quirements. - Page 4 WARNINGS/PRECAUTIONS WARNINGS/PRECAUTIONS 4.optical fiber fusion splicer is a calibrated precision instrument, please try to avoid strong vibration and impact. Special storage (storage time less than or equal to 6 months) is: -20℃~60℃. carry case should be used for storage, and suitable cushioning case should be added outside the carry case for long- 4.In order to ensure the safety of charging, the charging temperature range of lithium battery inside the welding machine distance transportation.
-
Page 5: Operation Key Combination Function
CHAPTER I OPERATION KEY COMBINATION FUNCTION OPERATION KEY COMBINATION FUNCTION Introduction of operation keys and parts The four function keys at the bottom of the screen, in addition to the basic functions (the first chapter introduces the The fusion splicer machine is mainly used fopermanent splicing fiber, the machine can continue to splice ordinary operation keys and parts), there are also some combined functions for daily maintenance of the machine. - Page 6 OPERATION KEY COMBINATION FUNCTION OPERATION KEY COMBINATION FUNCTION report an error,Please check whether the red light above the electrode is bright and dim(see electrode replacement for specific operations)If the 08 Camera LED: X Y Camera LED:two Function Description table fault persists,Please contact the after-sales service. Report an error,please check again.
-
Page 7: Display Menu Introduction
DISPLAY MENU INTRODUCTION INTRODUCTION TO SPLICE INTERFACE Heating time NAME ICON FUNCTION 15:11 Y screen display X screen display Normal Normal Splicing Mode For The Machine mode Bluetooth Fiber mode When the function is on the splicing machine will stop the final splicing process after in Splicing the completion of the fiber focus, end face detection and fiber alignment. - Page 8 INTRODUCTION TO SPLICE INTERFACE INTRODUCTION TO SPLICE INTERFACE different, and they need to be replaced with the same specifications or types.This error, can press continue to Intelligent prompt and fiber state prompt solution ignore the key error, mandatory welding. Ⅰ Intelligent prompt Note: according to the construction specifications of welding machine, different specifications and types of fiber The red symbol displayed at the bottom left of the LCD.
-
Page 9: Software Download
CHAPTER II SOFTWARE DOWNLOAD SCREEN MENU FUNCTION ON/OFF Software download Turn on the phone bluetooth, open the phone app, set the machine panel menu after establishing the connection, and machine will update at the same time. The splicing operation does not require phones, the phone App is only for machine menu settings, and splicer machine to store data.when the data is exported to phone App, the users can also get support through the APP and after-sales service. -
Page 10: Screen Menu Function On/Off
Normal mode “ “ icon close the o Calibration ". Then please strip login Signalfire 2 on your the screen fiber still flashes,please and cleave the windshield cover, the splicer phone, connect the Bluetooth,... -
Page 11: Chapter Ⅳ Fiber Stripping And Put Into Holder
CHAPTER Ⅳ FIBER STRIPPING AND PUT INTO HOLDER FIBER STRIPPING AND PUT INTO HOLDER Instructions for put fiber into holder: Jumper fiber(pigtail fiber) Rubbe insulated fiber Bare fiber Gtail Fiber/jumper Fiber Gtail Fiber/jumper Fiber Rubber insulated fiber Rubber insulated fiber Cable/bare fibe Cable/bare fibe With the yellow plastic laye as the... -
Page 12: Chapter Ⅴ Replace Electrode
CHAPTER Ⅴ REPLACE ELECTRODE REPLACE ELECTRODE Electrode replacement must use the genuine original electrode designed for this machine from factory. When the number of electrode is used close to 3000 times, the machine will remind you to replace it. When it reaches to 3000 times, it is necessary to replace the electrod and activate it then you can use again(see page 29 ACTIVATE ELECTRODE). -
Page 13: Chapter Ⅵ Activate Electrode
CHAPTER Ⅵ ACTIVATE ELECTRODE ACTIVATE ELECTRODE PS. The electrodes on the new machine do not need to activate we have activated before ex-factory. Only when the electrodes life on the machine is expired in the future mand then you need to replace activate the electrode if the server connection fails, hen the electrode is used up to 3000 times, you need to replace the electrode and activate it. -
Page 14: Chapter Ⅶ Smart Lock
Smart Lock Purpose: to facilitate management or owner's effective management of the splicer machine's You Need To Unbind Current Account First. use period or the number of splicing. Typical applications such as rental business. AI-6C：V02420145358411 device connected 2022-2-20 12:21:20 There is no phone attached to the machine AI-6C：V02420145358411... -
Page 15: Chapter Ⅷ Daily Maintenance
CHAPTER Ⅷ DAILY MAINTENANCE DAILY MAINTENANCE Ⅰ.Pay attention to dustproof and remove dust Ⅱ.Prevent Strong Shock or Vibration Bare fiber positioning groove, electrodes and microscopes must be kept clean and windshield cover should When you need to move or transport the fusion splicer, you should handle be closed when not in operation with care and gently. - Page 16 DAILY MAINTENANCE DAILY MAINTENANCE Ⅴ.Troubleshooting and solutions The table lists a general troubleshooting method for the user reference. Troubleshooting Reason Solutions When the user can not solve the situation, please contact with the suppliers directly. 1.Fiber core does not match (type or core diameter 1.Re-match the fiber to make the same type of fiber on Splicing points is different)
Need help?
Do you have a question about the AI-6C and is the answer not in the manual?
Questions and answers