Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Weber Markoprint integra Vivid
- Page 1 Translation of the original operating manual Markoprint integra Vivid Part number of documentation: 40106966 (GB) English Version: 11.03.2021/DC Weber Marking Systems GmbH Maarweg 33 D-53619 Rheinbreitbach E-Mail: info@webermarking.de http://www.webermarking.de...
- Page 2 Blank page...
-
Page 3: Table Of Contents
Contents 40 Markoprint Integra Vivid Contents GENERAL INFORMATION ........................ 5 ........................5 ENERAL URVEY ......................5 IMITATION OF IABILITY ........................ 5 ARRANTY LAUSE ......................5 OPYRIGHT ROTECTION ..............6 URPOSE AND COPE OF THIS SERVICE MANUAL SAFETY REGULATIONS ........................7 .................. - Page 4 Inhalt 40 Markoprint X1JET HMI ....................37 TATUS TEM AT RIGHT SIDE ..................37 AXIMUM VALUE FOR RIGHT ITEM SYSTEM SETTINGS......................... 38 ........................38 ENSOR NPUT ..................... 40 NTERN ULSE NCODER ....................40 ET ENCODER RESOLUTION 10. LAN SETTINGS ..........................41 .........................
-
Page 5: General Information
This documentation or parts of this documentation may only be copied, photocopied, reproduced or translated into other languages for personal use. Without previous expressed written permission of Weber Marking Systems GmbH a reproduction for circulation to a third party is not permitted. -
Page 6: Purpose And Scope Of This Service Manual
40 Markoprint Integra Vivid Purpose and Scope of this service manual This manual enables safe and effective use of the Markoprint integra Vivid. The Operating manual is a component of the device and must be stored close to the device to be accessible to the staff at all times. The staff must have read this manual thoroughly and understand the content before starting any work. -
Page 7: Safety Regulations
Safety Regulations 40 Markoprint Integra Vivid 2. Safety Regulations Behavior in Case of an Emergency The operating personnel have to be familiar with the operation and the location of safety, accident notification-, first aid- and rescue devices. What to do in Case of an Emergency? ... -
Page 8: Personal Protective Equipment
Safety Regulations 40 Markoprint Integra Vivid Personal Protective Equipment Wear following protective equipment when performing work at the system: SAFETY SHOES Wear for protection against falling off parts and slipping. PROTECTIVE CLOTHING Are tight-fitting clothes with low tensile strength, with tight sleeve... -
Page 9: Technical Specifications
Technical Specifications 40 Markoprint Integra Vivid 3. Technical Specifications General Dimensions 132,2 x 200,6 x 27,3 (excl. bracket and connections) (H x W x D in mm) Weight integra Vivid 1275g Weight Holder 500g Environmental 5 - 40 ° C... -
Page 10: Construction And Function
In addition, different print images can be selected and filled with data. System unit The Markoprint integra Vivid consists of a 7 inch display. The integra Vivid is equipped with an installation bracket for easy mounting. The Integra Vivid is controlled via a touch display. -
Page 11: Installation And Initial Operation
Installation and Initial Operation 40 Markoprint Integra Vivid 5. Installation and Initial Operation Safetynotes Danger to life through electric shock! DANGER TO LIFE! Contact with live parts poses imminent danger to life. Damaged insulation or individual components can be lethal. -
Page 12: Placing The Integra Vivid
Installation and Initial Operation 40 Markoprint Integra Vivid Edges and corners pose risk of injury! RISK OF INJURY! Sharp edges and pointed corners may cause abrasions and cuts to the skin. Therefore: – Be cautious when working near sharp edges and pointed corners. -
Page 13: Installation Of The Integra Vivid
Installation and Initial Operation 40 Markoprint Integra Vivid Installation of the integra Vivid Material damage due to improper print system installation! With the print system switched on, a defect may occur in the system electronics. Therefore: – Only install the system when it is switched off. -
Page 14: Connecting The Integra Vivid
Installation and Initial Operation 40 Markoprint Integra Vivid Connecting the integra Vivid The integra Vivid is connected via an optional 15-pin cable with male/female Sub-D connector. This is connected through 1:1. The cable must be ordered separately. Requirements The integra Vivid has been installed near the printing system. - Page 15 Installation and Initial Operation 40 Markoprint Integra Vivid Activation of the HMI To be able to use the integra Vivid, it must be activated once on the X1JET or PP 108. Requirements The HMI has been connected to the printing system ...
-
Page 16: Operation
40 Markoprint Integra Vivid 6. Operation The Markoprint integra Vivid can be used to enter and change various functions. These depend on the configuration of the respective printing system. Functions that are not enabled in the respective version of the system cannot be used via the integra Vivid. - Page 17 Operation 40 Markoprint Integra Vivid Menu Used to navigate in the different menus. Status light with status text Fault Yellow Warning Green Ready for operation Press the [Home] button briefly. The Home start screen is called up. Page 17 of 45...
-
Page 18: Switch On
Operation 40 Markoprint Integra Vivid Switch ON The system starts automatically with the connected print system. Switching on separately is not possible. After switching on, a boot screen with a progress bar appears during startup. Switch OFF The system is automatically deactivated, together with the connected print system. -
Page 19: Menu Structure Of The Markoprint Integra Vivid
Operation 40 Markoprint Integra Vivid Menu structure of the Markoprint integra Vivid Home Screen Status Print Image selection All settings can be changed popularly (see picture explanation). 1. The print position can be adjusted step by step by tapping or holding the (+) and (-) field. -
Page 20: Print Stopp
Operation 40 Markoprint Integra Vivid Print stopp To avoid accidental touching of the start, pause and stop buttons, it has been programmed with a 3-second delay. The delay is visible in the blue bars. Instruction Please activate a print stopp / print pause as follows:... -
Page 21: Print Start
Operation 40 Markoprint Integra Vivid Print start Instruction Please activate a print start as follows: Step Procedure Press and hold the [Start] key on the integra Vivid. The device status LED lights up green when print assignment is successful Print start Print images can be selected directly via the touch display. -
Page 22: Variable Input
Operation 40 Markoprint Integra Vivid Step Procedure Scroll through the stored print images by dragging them up and down. Confirm the print image selected for printing by touching the [Start] button. Variable input The input of variable data is possible from the system version Advanced. -
Page 23: Input Counter Start Value
Operation 40 Markoprint Integra Vivid Input counter start value The entry of a counter value is possible from the system version Advanced. There are two options for generating start values for print images that contain a counter field. On the one hand, the start value, entered in the print image, can be accepted, and on the other hand, the start value can be entered at the control unit. -
Page 24: Print Head Settings
Print Head settings 40 Markoprint Integra Vivid 7. Print Head settings Print position / Print start delay The printing position is the distance between the detection of the product by the sensor (photocell) and the beginning of the printing process. - Page 25 Print Head settings 40 Markoprint Integra Vivid Instruction Please set up the print start delay in the control system as follows: Step Procedure Tap the menu button. The Settings menu is displayed. Tap the print head button. The print start delay / print position menu is displayed.
-
Page 26: Print Speed
Print Head settings 40 Markoprint Integra Vivid Print speed If the product speed is uniform, the use of a rotary encoder can be dispensed with. For this purpose, a fixed speed can be set in the Speed submenu. This menu is only available if the menu Internal clock / encoder is set to Internal. -
Page 27: Intensity
Print Head settings 40 Markoprint Integra Vivid Intensity In the Intensity menu, the print density is set in DPI. Print image contrast. If necessary, this parameter may have to be changed to optimise the print image to the product surface. Higher intensity means increased density and slower drying of the ink. -
Page 28: Print Direction
Print Head settings 40 Markoprint Integra Vivid Print direction The parameter print direction indicates the direction of movement of the product on the conveyor belt viewed from the controller in the print direction. The setting options are from left to right or from right to left. -
Page 29: Nozzle Row
Print Head settings 40 Markoprint Integra Vivid Step Procedure Select the desired setting by tapping Nozzle row The setting of the nozzle rows is only possible for using HP or LX print heads. Each HP- or LX- ink cartridge has two nozzle rows (A and B). One nozzle row has 150 nozzles. - Page 30 Print Head settings 40 Markoprint Integra Vivid Nozzle row Description A ~ B Printing with both nozzle rows, alternating. The first print image is printed with nozzle row A and the second text with nozzle row B. Vertical resolution: 300 dpi A + B Printing with both nozzle rows together.
-
Page 31: Upside Down
Print Head settings 40 Markoprint Integra Vivid Step Procedure Select the desired setting by tapping Upside down The Upside down setting causes the print image to be printed overhead. Instruction Please set up the upside down print as follows: Step Procedure Tap the menu button. - Page 32 Print Head settings 40 Markoprint Integra Vivid Step Procedure Tap the Print head button. The Print position menu is displayed. Call the Upside down menu by dragging and tapping the dots to scroll through the setting levels. The Upside down menu is displayed.
-
Page 33: Repeat Distance / Print Repeat Number
Print Head settings 40 Markoprint Integra Vivid Repeat distance / Print repeat number To print several print images on one product, the number of print images and the distance between them must be specified. The distance between print images is measured from print start to print start. -
Page 34: Display Settings
Display settings 40 Markoprint Integra Vivid 8. Display settings Language In this menu the desired menu language of the device can be set. Page 34 of 45... -
Page 35: Display Mode
Display settings 40 Markoprint Integra Vivid Display Mode Various settings can be made under the display mode, such as Color mode or Dark mode. The display image can be rotated depending on the mounting mode. Hide disabled menus is not yet activated. -
Page 36: Date / Time
Display settings 40 Markoprint Integra Vivid Date / Time The date and time of the printing system are displayed in this menu or can be set here. Instruction Please set up the date / time as follows Step Procedure Tap the menu button. -
Page 37: Status Item At Right Side
Display settings 40 Markoprint Integra Vivid Status Item at right side In this menu the status display can be changed. E.g. from speed to prints/sec, prints/min and prints/hour. Maximum value for right item In this menu the maximum value of the right status display can be changed. E.g.: for a conveyor belt, using a rotary encoder, that can reach up to 30 m/min, the maximum value is set to 30. -
Page 38: System Settings
System Settings 40 Markoprint Integra Vivid 9. System Settings Sensor Input This menu is used to set which sensor input is used. Internal is selected if the sensor integrated in the housing is used, if available. External is selected if an optionally available sensor is connected. - Page 39 System Settings 40 Markoprint Integra Vivid Instruction Please select the sensor as follows Step Procedure Tap the menu button. The Settings menu is displayed. Tap the System button. The Sensor menu is displayed. Select the desired setting by tapping. Page 39 of 45...
-
Page 40: Intern Pulse / Encoder
The intensity setting is optimized to 600 dpi for the Weber Marking Systems GmbH rotary encoder. Fine adjustment may have to be made by the test image. -
Page 41: Lan Settings
LAN Settings 40 Markoprint Integra Vivid 10. LAN Settings Own IP-address In this menu the IP-address is displayed and can be set. Page 41 of 45... -
Page 42: Ip-Mask
LAN Settings 40 Markoprint Integra Vivid IP-mask In this menu the IP-mask is displayed and can be set. Gateway Display and setting of the gateway address. To set the required values for the network, contact the responsible network administrator Page 42 of 45... -
Page 43: Configurations
Configurations 40 Markoprint Integra Vivid 11. Configurations Page 43 of 45... -
Page 44: Technical Drawings
Technical Drawings 40 Markoprint Integra Vivid 12. Technical Drawings Markoprint integra Vivid touch Page 44 of 45... - Page 45 Technical Drawings 40 Markoprint Integra Vivid Page 45 of 45...
Need help?
Do you have a question about the Markoprint integra Vivid and is the answer not in the manual?
Questions and answers