Marvin Sliding Door Automatic Control Device Installation Instructions Manual

Table of Contents

Quick Links

Download this manual

Sliding Door Automatic Control Device

Installation Instructions

ABSTRACT: Use this site prep guide in conjunction with the Sliding Door Automatic Control Site Prep Instruction.

Install the door prior to installing the motor. The following instructions assume the installer has prior product and in-

stallation training before attempting to install the device.

The motor and control box are complete units and must not be disassembled in the field.

Tools Needed .............................................................. 1

Door/Stud/Motor Cavity Prep ...................................... 2

Wiring Prep ................................................................. 3

Install the Pulley Corner Key....................................... 4

Install the Motor .......................................................... 5

Install the Control Box ................................................. 7

Tools Needed

• 14 gauge cable crimper

• Wire stripper

• Power drill/driver

• 1 1/4" drill bit

• 7/64" drill bit

• 9/64" Allen Wrench

Always practice safety! Wear the appropriate eye, ear, and hand protection, especially when working with power

tools.

I M P O R T A N T

Connecting Components............................................. 9

Threading the Belt......................................................11

Installing the Optional Closing Ramp ........................ 15

Optional Belt Clips..................................................... 16

Programming............................................................. 17

Reprogramming ........................................................ 18

• 3/32" Allen wrench

• Measuring tape

• Heavy duty shear (for cutting the belt)

• Extended #2 Phillips bit

• Safety glasses

WAR N I NG!

2022-09-08

19916437

Table of Contents

Need help?

Do you have a question about the Sliding Door Automatic Control Device and is the answer not in the manual?

Questions and answers

Summary of Contents for Marvin Sliding Door Automatic Control Device

Page 1: Table Of Contents
Sliding Door Automatic Control Device Installation Instructions ABSTRACT: Use this site prep guide in conjunction with the Sliding Door Automatic Control Site Prep Instruction. Install the door prior to installing the motor. The following instructions assume the installer has prior product and in- stallation training before attempting to install the device.
Page 2: Door/Stud/Motor Cavity Prep
1 1/4" x 2 1/2" deep notch lined up with the belt pass- through on the corner key. When installation is complete cover the notch with a steel tie plate. Figure Figure 2 Notched stud Steel stud tie Notch 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 3: Wiring Prep
Blue CAT5e cable ran from the interior and exterior wall switches to the motor or controller. (Can be daisy chained) Yellow CAT5e cables ran from each sensor to the motor. Power cable is supplied 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 4: Install The Pulley Corner Key
Figure 4 3. Fasten the pulley corner key into the head jamb rough opening with two #8 x 3" screws. provided.See Figure Figure 5 Figure 7 #8 x 3" screws 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 5: Install The Motor
1. Install a screw on their centerline within 3" of the stud and leave the head proud about 3/4"-1". Figure 9 3. Pre-drill with a 7/64" drill bit and fasten the four corners with #8x 3" screws provided Figure 8 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 6 (Note the area marked with a red arrow in Figure 10 (next page). Figure 10 Drive pulley shown with belt attached Set screws (2) are located at 90 degrees from each other 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 7: Install The Control Box
Fasten all screws to securely mount the control box (4 screws for rear mount, 2 screws for side mount). See Figure Figure 13 Knockouts 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 8 5. Remove the battery cover and battery from the control box. Connect the two loose red battery cables together to complete the circuit. Replace the battery and battery cover/nut. See Figure 15 Figure Figure 16 Battery cables. 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 9: Connecting Components
See Figure Figure 19 Wall switch "out" port. Figure 18 Ensure a solid crimp 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 10 The sensor eye will fit through the hole in the cover. See Figure Figure 21 Inset shows sensor eye through head jamb cover Sensor through head jamb cover 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 11: Threading The Belt
See Figure 26 Figure 23 3. Attach belt on panel bracket and fasten with #8- 32 x 3/8" screw. See Figure Figure 25, and Figure Figure 26 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 12 Ensure that termination of the belt is on the exterior side Figure 29 of the door. Cut next to the "tooth" End tooth is fully engaged with clamp Figure 28 Holes in stud to access corner key Belt 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 13 See Figure Figure 30 Figure 32 Turnbuckle Belt Barrel Clip Lock nut Figure 31 Turnbuckle Set screws 8. Tighten turnbuckle nut until belt is taut, ensuring turnbuckle ends don’t spin (twisting belt). 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 14 12. With panels in locked position, slide the clamp into Bi-Parting units only. the route and fasten with two screws. Ensure the clamp is engaged with the teeth on the belt. See Figure 35 Figure 35 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 15: Installing The Optional Closing Ramp
4. Install the closing ramp, using the provided #8 x 3" screw, into the pre-drilled hole. 5. Close and lock the door. 6. Pull the ramp tight so that if fully contacts the turnbuckle. See Figure 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 16: Optional Belt Clips
(opposite of the turnbuckle or bi-parting bracket) with teeth up against the head track. Fasten the belt clip in the head track with the screws provided. Pre-drilling may be necessary. See Figure Figure 39 Belt clip 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 17: Programming
"Release Button!" or red and blue lights blink rapidly (on non-touch screens). See Figure 7. Once the door stops and is engaged in the closed position, the programming is complete. 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...
Page 18: Reprogramming
3. Turn on both AC and Battery power switches on the control box cover. Open the control box and flip dip switch 8 back to the left. See Figure Figure 44 Dipswitch 8 4. Refer to Programming on page 2022-09-08 Sliding Door Automatic Control Device 19916437 Installation Instructions...