Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for BIN SENSE SOLO LTE-M
- Page 1 SOLO LTE-M SOLO 4G/3G (SK) USER MANUAL 700050-BS May 2022 Version 1.0...
- Page 2 INTENTIONALLY BLANK 700050-BS May 2022 Version 1.0...
-
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION CUSTOMER SUPPORT ..........................3 SOLO CERTIFICATIONS ..........................4 SOLO....................................4 SOLO-SK..................................4 MANUFACTURER’S WARRANTY ......................... 4 HOW TO OBTAIN WARRANTY SERVICE ........................5 SAFETY................................6 STANDARDS ................................. 6 OVERVIEW OVERVIEW..............................7 PACKAGE CONTENTS..............................7 MASTER UNIT OVERVIEW ............................7 INSIDE THE MASTER UNIT ............................ - Page 4 INTENTIONALLY BLANK Page 2 May 2022 Version 1.0 www.binsense.com...
-
Page 5: Customer Support
CUSTOMER SUPPORT For warranty service, please contact your local dealer. For product support, troubleshooting, or additional questions with your Bin-Sense™ device, please contact your local dealer (www.binsense.com/locate-a-dealer) or IntraGrain Technologies Inc. at: support@intragrain.com 1.833.570.7979 www.binsense.com Download the Bin-Sense mobile app to set up Bin-Sense Solo! play.google.com/store/apps/ apps.apple.com/ca/app/bin- details?id=com.intragrain.binsense... -
Page 6: Solo Certifications
SOLO CERTIFICATIONS SOLO • FCC ID: 2AUTY-106104-SO-LT • Contains FCC ID: XPYUBX19KM01; IC 8595A-UBX19KM01 SOLO-SK • FCC ID: 2AUTY-106104-SO-4G • Contains FCC ID: XPY1EIQ24NN; IC 8595A-1EIQ24NN This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 7: How To Obtain Warranty Service
WHAT THIS WARRANTY DOES NOT COVER This warranty does not cover normal wear of parts or any damage resulting from any of the following: negligent use or misuse of the product; damage in transport, natural disaster, improper installation or use, improper abuse or improper handling. -
Page 8: Safety
SAFETY READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Use the Solo device for its intended use only, as described in this manual. Do not use attachments not recommended by the manufacturer. STANDARDS This manual will use the following standard safety terms and conventions to indicate conditions: WARNING: INDICATES A HAZARDOUS SITUATION RESULTING IN SERIOUS INJURY OR DEATH. -
Page 9: Overview
Two different versions of Solo are available depending on the cellular service available in the area. Solo LTE-M The Solo LTE-M uses new LTE-M technology optimized for Internet-of-Things (IoT) applications, recommended for use across North America, excluding Saskatchewan. Solo 4G/3G (SK) The Solo 4G/3G (SK) version uses a conventional 4G cellular connection with 3G backup (where still available)—... -
Page 10: Inside The Master Unit
INSIDE THE MASTER UNIT A. CELLULAR ANTENNA B. STATUS LED C. 4 X AA BATTERY CLIP D. ADDITIONAL 4 X AA BATTERY CLIP (SOLO 4G/3G ONLY) E. SIM CARD F. TEST BUTTON G. RESET BUTTON Figure 2: Bin-Sense Solo - Interior Page 8 May 2022 Version 1.0 www.binsense.com... -
Page 11: Installation
INSTALLATION WARNING: FALL HAZARD - EXTREME CARE AND CAUTION MUST BE USED WHEN CLIMBING IN A BIN OR SILO. BE SURE TO USE APPROVED SAFETY PROCEDURES AND MATERIALS. WHEN WORKING ABOVE 1.2 METERS, WEAR A SAFETY HARNESS OR PERSONAL PROTECTIVE EQUIPMENT. AN APPROVED TOOL BELT MUST BE WORN TO KEEP BOTH HANDS FREE WHEN CLIMBING UP AND DOWN A LADDER. -
Page 12: Solo Unit Installation
Note: Solo units can read a maximum of four cables with up to 12 sensors each. 3. Open the four latch clips and remove the lid from the Solo unit. 4. Remove the “Remove before use” tab(s) from the battery clip(s). Solo LTE-M has one battery tab, Solo 4G/ 3G (SK) has two battery tabs. -
Page 13: Diagnostics
DIAGNOSTICS LED DIAGNOSTICS The diagnostic LED on the Solo units give information about any attached sensor cables as well as cellular connection status. STARTUP STATUS When a Solo device is first powered on and connecting the Bin-Sense servers, the status LED will show different colour and flash patterns to convey the current status. - Page 14 Flash Colour Value Orange Green The status LED will only flash a specific number of red flashes if the corresponding number is not zero. For example, if there are no moisture cables connected to the Solo unit, the LED will not flash three red flashes. If nothing is detected on the sensor cable interface, the LED will flash once.
- Page 15 Manufactured in Canada by: Head Office: IntraGrain Technologies Inc. 118 Husum Road RM of Sherwood, SK CANADA S4K 0A4 support@intragrain.com 1-833-570-7979 www.binsense.com...
Need help?
Do you have a question about the SOLO LTE-M and is the answer not in the manual?
Questions and answers