Advertisement
Quick Links
FCC Information to Users
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications However, there is no
guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorientate or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Warning: Changes or modifications not expressly approved by
Lectronic Kaddy Corporation could void the user's authority to
operate the equipment.
Quick Start
Manual
To get your game up and
running quickly with
for more comprehensive
instructions refer to your
owners manual
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for LECTRONIC KADDY Dyna-Steer 2000
- Page 1 Consult the dealer or an experienced radio/TV for more comprehensive technician for help. instructions refer to your Warning: Changes or modifications not expressly approved by owners manual Lectronic Kaddy Corporation could void the user's authority to operate the equipment.
- Page 2 Connect battery and ensure that the plug is securely inserted into the socket. Press "On" button to power up the ‘Kaddy. From the main control panel:- Data Panel Pressing the green bar ("Start") will start the ‘Kaddy moving. illustration Pressing the red bar ("Dynamic Brake") will Here stop the kaddy by applying the brakes.
- Page 3 To start the ‘Kaddy using your remote control, hand held, transmitter, simply press the centre round button.(see illustration) Holding down this button will gradually increase the speed of the ‘Kaddy. Release the button when the desired speed has been reached, the ‘Kaddy will then maintain this speed. To stop the ‘Kaddy, press the lower round button once.
- Page 4 When traveling down hill, the ‘Kaddy will not turn as effectively. This ensures that the ‘Kaddy will remain stable at all times. To effect turns in these circumstances, first stop the ‘Kaddy prior to activating the turn, as described above. When traveling up hill, the ‘Kaddy will be more responsive when turning.
- Page 5 Back Front Turn L.E.D. Start/Speed Stop/Brake User Code Strap 9V Battery...
-
Page 6: Replace Battery
Replace Battery Open the transmitter case by sliding the battery cover to expose the battery. Remove the battery and disengage the polarized connector. Do not stress the wires by dangling the battery while still connected. Replace the battery with the specified alkaline battery. Replace the cover. - Page 7 Transmitter Specification Receiver Specification...
Need help?
Do you have a question about the Dyna-Steer 2000 and is the answer not in the manual?
Questions and answers
Where do I get the battery for the cset
You can find a battery for the LECTRONIC KADDY Dyna-Steer 2000 at Batteries Expert, located at 1755 Plummer St #20, Pickering, ON.
This answer is automatically generated
Battery voltage is what? A new 12 V battery only lights up one green light on control panel
The transmitter for the LECTRONIC KADDY Dyna-Steer 2000 uses a 9-volt alkaline battery.
This answer is automatically generated
Hi there, can you please help me out, my battery reads fully charged but the torch pad shows 1 red light on low when installed. Also where can I get a full manual. How long will a battery last since the unit hasn't been used much. Thank you for your help.
If the LED light on the transmitter appears as a solid light instead of flashing rapidly when a button is pressed, it indicates that the 9-volt battery in the transmitter needs to be replaced, even if it seems fully charged. This could cause incorrect signals, such as the torch pad showing a red light on low.
This answer is automatically generated