Table of Contents
Advertisement
Quick Links
142-BR500
Portable cordless edgebander for ABS
Operationg instructions
Distributor:
IGM nástroje a stroje s.r.o.
Ke Kopanině 560, 252 67, Tuchoměřice
Czech Republic, EU
Phone: +420 220 950 910
E-mail: sales@igmtools.com
Website: www.igmtools.com
PDF ONLINE
www.igmtools.info
2022-07-12
142-BR500 IGM Portable Edgebander for ABS Manual EN v2.4.00 A4ob
Advertisement
Table of Contents
Summary of Contents for IGM BR500
- Page 1 Operationg instructions Distributor: IGM nástroje a stroje s.r.o. Ke Kopanině 560, 252 67, Tuchoměřice Czech Republic, EU Phone: +420 220 950 910 E-mail: sales@igmtools.com Website: www.igmtools.com PDF ONLINE www.igmtools.info 2022-07-12 142-BR500 IGM Portable Edgebander for ABS Manual EN v2.4.00 A4ob...
-
Page 2: Table Of Contents
Because of our policy of constant improvement, the design, construction or pictures may differ slightly. Should you discover any mistakes, please contact us at podpora@igm.cz. Table of contents 6.1.3 Adjusting the amount of glue DECLARATION OF CONFORMITY 6.1.4 Adjusting tape thickness... -
Page 3: Safety Instructions
Operating instructions EN 3. SAFETY INSTRUCTIONS sure that it runs smoothly and that the protective covers are working. Replace any deficiencies or 3.1 Notice damaged parts. The machine may only be used when This machine is designed for work with wood and in perfect technical condition. -
Page 4: Risks
Operating instructions EN 3.3 Risks 3.4 Important notice Risk exists even when using the machine according to Make sure the machine has been off for at least 60 minutes the manual. before storing it in the portable case. That way, the glue in the container will cool down to 60°C. -
Page 5: Contents
Operating instructions EN 4.3 Contents Edgebander Support table Corner guide End trimmer Light transport bag Sample tape from calibration procedures 5. 5. TRANSPORT, UNPACKING AND ASSEMBLY 5.1 Transport and unpacking The machine is not assembled due to transport. Assemble before operating. Remove the edgebander from the packaging and place on a flat surface. -
Page 6: Control And Gauge Set Up On The Supporting Table
screw (1) and place guiding place onto the workpiece. When the workpiece perpendicular to the pressure roller, tighten the screw (1). Loosen the screw (3), adju the plate to “0” (4) then tighten screw (3) again. Operating instructions EN Glue Adjustment 6.1.2 Control and gauge set up of the support table 6.1.3 Adjusting the amount of applied glue The ... -
Page 7: Fastening The Workpiece Before Edge Banding
Operating instructions EN 6.1.6 Proper fastening before edgebanding - Use glue supplied by IGM which has an operating Fasten the workpiece to a worktop using clamps. Make temperature of 120-150 °C. sure the edge of the workpiece you will edgeband - Use the lowest feed speed when turning on the extends beyond the edge of your worktop. -
Page 8: Working With The Edgebander
Operating instructions EN The display shows the current How to switch between °C a °F temperature in the glue pot When the light is on, the temperature Operating indicator light: lights up is in °C and feed speed in m/min. when the temperature is over 120 °C (250 F), you can speed up the heating When the light is on, the temperature... -
Page 9: Stationary Use
Loosen screws, see (pic.17), and remove the plastic 9.1 BR500 error messages cover. Now you can lubricate the chain and the plate. The BR500 Edgebander is designed to detect After maintenance, place the cover back and tighten malfunctions and to picture them on its display. -
Page 10: Environmental Protection
Your machine contains materials that can be recycled. IGM Straightline Edgebanding and Trimming Kit for Please, let specialized institutions handle the machine. Worktable ST95A 142-ST97 Glue Technomelt KS224 for IGM Manual Edgebanders - 11.ACCESSORIES (spare parts) M967-1 1kg pack iGM Tape Holder for Edgebander DR500-BR300...