Download Print this page

Advertisement

Quick Links

Advertisement

loading
Need help?

Need help?

Do you have a question about the HELP V and is the answer not in the manual?

Questions and answers

Summary of Contents for HandyTech HELP V

  • Page 2 Congratulations on the purchase of the lifter HELP V. We wish You an advantageous use. The lifter HELP V is very easy to use and extensively described in these instructions. Read the use and maintenance instructions carefully before using the vehicle.
  • Page 3 The manufacturer guarantees the product for 24 months, only if the maintenance operations have been implemented by an authorized Handytech Centre. It is advisable to use the lifter HELP V on a flattest terrain possible and to avoid muddy and gravel grounds During the use it is necessary to check that near the lifter there are not people, animals or objects that could interfere with the movement of the lifter.
  • Page 4 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 3. Use □ Before starting every operation, engage the handbrake of the vehicle. □ Completely open the sliding door and check that the space available allows the rotation and the way down of the lifter and that there is the possibility to move the wheelchair.
  • Page 5 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 MOD. FT04 rev.01 Turning the battery master switch in mode on will activate the red LED on the control unit box (Photo 4). Photo 4 □ If the two half of the platform are closed, it is necessary to place vertically the front part lifting it until getting a 120 degrees angle with the other half, and then take it back to about 90 degrees with the platform, as shown in Photo 5,6,7.
  • Page 6 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 The opening operation of the lifter cannot be carried out with the two half of the platform closed because it can create a collision with the door on some type of vehicles (Photo 8).
  • Page 7 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 □ Push the way up button and keep pressed until the lifter will stop. Then push the rotation button which activates also the bumper, paying attention to the completely opening of the door to avoid a collision of the platform with this last one.
  • Page 8 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 MOD. FT04 rev.01 Complete the operation making the wheels of the wheelchair touch the safety stop on the front half of the platform and then block the wheelchair using the original brakes (Photo 13).
  • Page 9 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 □ If necessary, close the front part of the platform by lifting the mechanical unblocking knob fixed on the upright, taking with the other hand the flap towards yourself first, and then closing it on the rear part of the platform (Photo 16,17,18).
  • Page 10 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 WHAT TO DO IF … 1. The lifter does not move when pushing the way up button Check that the battery master switch is in mode ON.
  • Page 11 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 4. Manual emergency system THIS OPERATION CAN BE CARRIED OUT ONLY ONCE, SO IT IS COMPULSORY TO CONTACT AS QUICKLY AS POSSIBLE THE NEAREST HANDYTECH CENTRE It is necessary to unscrew anticlockwise, using a L hex key 6mm, the cap located on the electric actuator.
  • Page 12 Do this operation carefully not to create dangers for the person transported. Then contact the nearest Handytech Centre. If your system has a problem which is not listed, contact the nearest Handytech Centre. - 11 –...
  • Page 13 Repeat the check done in the first check. NOTA BENE: After 2 years go to your usual Handytech Centre to have the system state checked and to replace any parts that need to be replaced. When the guarantee ends the maintenance program is at your own discretion, but our advice is to follow it scrupulously because neglect can cause system faults, problems and create dangerous situations while driving.
  • Page 14 MOD. FT04 rev.01 HELP V (use and maintenance) Ed. 3 - updated: 12/2018 PER STAMPA: LAY OUT RETRO - 13 –...

This manual is also suitable for:

Ft04