Advertisement
Quick Links
Fiber Fabry-Perot Tunable Filter
First Time User Manual
C o p y r i g h t © 2 0 0 9 M i c r o n O p t i c s , I n c .
Micron Optics Inc.
1852 Century Place NE
Atlanta, GA 30345 USA
Fiber Fabry-Perot Tunable Filter | FFP-TF2
phone
404 325 0005
fax
404 325 4082
www.micronoptics.com
F i r s t T i m e U s e r M a n u a l
|
FFP-TF2
1
Advertisement
Summary of Contents for Micron Optics FFP-TF2
- Page 1 Fiber Fabry-Perot Tunable Filter | FFP-TF2 Fiber Fabry-Perot Tunable Filter FFP-TF2 First Time User Manual Micron Optics Inc. phone 404 325 0005 1852 Century Place NE 404 325 4082 Atlanta, GA 30345 USA www.micronoptics.com C o p y r i g h t © 2 0 0 9 M i c r o n O p t i c s , I n c .
- Page 2 This document was prepared for first-time users of the FFP-TF2. Additional critical information can be found online at www.micronoptics.com. As a first time user, you should find this handbook valuable in helping you get the most out of your filter as soon as possible.
-
Page 3: Getting Started
Fiber Fabry-Perot Tunable Filter | FFP-TF2 GETTING STARTED (1) Carefully unpack the filter from the special shipping case, taking extra care to avoid breaking the optical fiber (fig. 1). NOTE: the filter is shipped with a loose-tube jacket to provide added protection to the fiber pigtails. Pulling on the fiber while holding onto the jacket can break the fiber inside the filter enclosure and destroy the filter. - Page 4 Fiber Fabry-Perot Tunable Filter | FFP-TF2 Figure 3. FFP-C front panel. (c) Plug the AC power cord into the rear panel of the FFP-C unit and turn the power on. (d) Connect the FFP cable to the controller. Attach the red clip lead to the (+) terminal and the black lead to the (-) terminal.
- Page 5 Fiber Fabry-Perot Tunable Filter | FFP-TF2 Typical Oscilloscope Configuration (1) Connect the FFP-C PZT, Test, and Sync output BNC connections to your oscilloscope channels 1, 2, and external trigger respectively. To channel 2 To external To channel 1 trigger input Figure 5.
- Page 6 Fiber Fabry-Perot Tunable Filter | FFP-TF2 Typical Optical Configuration Optical Source Output Coupler Photo-detector Input C o p y r i g h t © 2 0 0 9 M i c r o n O p t i c s , I n c .
- Page 7 Fiber Fabry-Perot Tunable Filter | FFP-TF2 Note: This is a representative oscilloscope display of the scan voltage and the corresponding filter response. C o p y r i g h t © 2 0 0 9 M i c r o n O p t i c s , I n c .
- Page 8 Fiber Fabry-Perot Tunable Filter | FFP-TF2 Modes of Operation: Manual vs. Scan vs. Dither The tunable filter and controller can operate in one of three modes: (1) Manual, (2) Scan, and (3) Dither (or locked). In Manual mode, the amplitude and frequency knobs are turned completely counter-clockwise.
- Page 9 Since the damage threshold scales inversely with finesse rating of the filter; the lower finesse filters can withstand higher optical power. For more information on this or any other Micron Optics product, please contact us Micron Optics, Inc. 1852 Century Place, NE...
Need help?
Do you have a question about the FFP-TF2 and is the answer not in the manual?
Questions and answers