Advertisement
NOTE:
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed
in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
2. INTRODUCTION
Modern design convector heater with three heat settings of 750/1250/2000W for gradual control of heating elements. Rotary controlled room
thermostat maintains ambient temperature at preset level, with the addition of a thermal cut-off and overheat protection. Features hard-wearing
feet to allow for maximum stability. Slimline, sturdy construction and high quality finish make this unit suitable for home, light industrial and office
environments. Supplied with 3-pin plug.
3. SPECIFICATION
Model No: .................................................................2013.V2
Power: ......................................................... 750/1250/2000W
Size (W x D x H): ....................................620 x 224 x 380mm
Supply: ...........................................................................230V
4. ASSEMBLY
4.1.
To fit the feet, align them as in fig.1 and secure with the
self tapping screws provided.
5. OPERATION
5.1.
Place the heater in a suitable position in the area you require to heat.
5.2.
Allow a minimum of 50cm between the heater and adjacent objects such as furniture etc.
5.3.
Plug the heater into the mains supply.
5.4.
Turn the thermostat knob (fig.2.C) to a high setting.
5.5.
SELECTING THE HEAT OUTPUT (fig.2)
Choose the required heat output by selecting the appropriate switch which will light up when pressed.
Low setting
Medium setting
High setting
5.6.
USING THE THERMOSTAT (fig.2.C)
Once the required room temperature has been achieved, turn the thermostat down slowly in the direction of the min. setting until the
heat output switch light goes out. The heater will then keep the surrounding air at the set temperature by switching on and off at
intervals. You may reset the thermostat at any time.
5.7.
SAFETY CUT OUT FEATURE
The heater is fitted with a thermostatic safety cut out which will turn the heater off automatically should the airflow become blocked or if
the heater has a technical malfunction. Should this happen, switch the heater off and unplug it from the mains power
supply.
WARNING! In such a case the heater will be very hot.
‰
DO NOT connect the heater to the power supply again until the reason the safety cutout activated has been identified. Allow the heater
8
to cool completely before handling and then check the air inlet and outlet for obstructions before attempting to switch the unit back on.
If the cause is not obvious return the heater to your local Sealey stockist for servicing.
6. MAINTENANCE
WARNING: Before attempting any maintenance ensure the unit is unplugged from the mains power supply and that it is cool.
‰
6.1.
Clean the unit with a soft dry cloth. DO NOT use abrasives or solvents.
6.2.
Periodically check the air inlet and outlet to ensure the air way is clear.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our
technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
(750W)
Select switch 'A'
(1250W)
Select switch 'B'
(2000W)
Select both switches.
01284 703534
Original Language Version
fig.1
sales@sealey.co.uk
fig.2
www.sealey.co.uk
CD2013.V2 Issue:2 (H) 10/03/22
Advertisement
