Summary of Contents for MQ Multiquip Mikasa MVC-64H
Page 1
OPERATION AND PARTS MANUAL Plate Compactor Models MVC-64H/HW (Honda GX120K1 Gasoline Engine) Revision #4 (10/20/05) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Order via Internet (Dealers Only) Best Deal! If you have an MQ Account, to obtain a Order parts on-line using Multiquip’s SmartEquip website! Username and Password, E-mail us at: ■...
MVC-64H/HW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! HAZARD SYMBOLS Potential hazards associated with the operation of the MQ Safety precautions should be followed at all times when operating Model MVC-64H/HW Plate Compactor. will be referenced this equipment.
Page 9
MVC-64H/HW — SAFETY MESSAGE ALERT SYMBOLS CAUTION - Equipment Damage Hazards CAUTION - Rotating Parts Hazards NEVER operate equipment with covers, Other important messages are provided throughout this or guards removed. Keep fingers, hands, manual to help prevent damage to your light tower, other hair and clothing away from all moving property, or the surrounding environment.
MVC-64H/HW — RULES FOR SAFE OPERATION ■ NEVER touch the hot exhaust CAUTION - Read Manual! manifold, muffler or cylinder. Allow these parts to cool before servicing Failure to follow instructions in this engine or mixer. manual may lead to serious injury or ■...
Page 11
MVC-64H/HW — RULES FOR SAFE OPERATION ■ NEVER run engine without air filter. Severe engine damage TRANSPORTING may occur. ■ ALWAYS shutdown engine before transporting. ■ ALWAYS service air cleaner frequently to prevent carburetor ■ Tighten fuel tank cap securely and close fuel cock to malfunction.
MVC-64H/HW — OPERATION AND SAFETY DECALS Machine Safety Decals The MVC-64H/HW Plate Compactor is equipped with a number of safety decals (Figure 2). These decals are provided for operator safety and maintenance information. The illustration below shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
MVC-64H/HW — GENERAL INFORMATION Definition of Plate Compactor Frequency/Speed The Mikasa MVC-64H/HW is a walk behind, plate compactor The compactor's vibrating plate has a frequency of 5,600 vpm designed for the compaction of sand, mixed soils and asphalt. (vibrations per minute). The travel speed of the compactor is This plate compactor is a powerful compacting tool capable of approximately 82 ft./minute (25 meters/minute).
MVC-64H/HW — COMPONENTS (PLATE COMPACTOR) Figure 3. MVC-64H/HW Plate Compactor Components Figure 3 shows the location of the components and general Belt Cover – Remove this cover to gain acess to the V- maintenance parts. The function of each component is described belts.
MVC-64H/HW — COMPONENTS (HONDA GX120K1SM12 ENGINE) Figure 4. Engine Controls & Components INITIAL SERVICING Spark Plug – Provides spark to the ignition system. Set The engine (Figure 4) must be checked for proper lubrication and spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) for filled with fuel prior to operation.
Page 16
MVC-64H/HW — INSPECTION The Oil Alert system will Before Starting automatically stop the engine NOTE 1. Read safety instructions at the beginning of manual. before the engine falls below safe limits. Always be sure to check 2. Clean the compactor, removing dirt and dust. Particularly, the the engine oil level prior to starting bottom of the plate, engine cooling air inlet, carburetor and the engine.
Page 17
MVC-64H/HW — INSPECTION V-Belt Check 2. The V-belt tension is proper if the V-belt bends 10 to 15 mm (Figure 10) when depressed with finger at midway between Caution - V-Belt check the clutch and vibration pulley shafts. NEVER attempt to check the V-belt with the engine running. Severe injury can occur if your hand (Figure 7) gets caught between the V-belt and the clutch.
MVC-64H/HW — INITIAL START-UP The CLOSED position of the Caution - Read Manual choke lever enriches the fuel NOTE mixture for starting a COLD DO NOT attempt to operate the plate compactor engine. The OPEN position until the Safety, General Information and provides the correct fuel mixture Inspection sections of this manual have been for normal operation after...
Page 19
MVC-64H/HW — INITIAL START-UP/OPERATION 6. If the engine has started, slowly return the choke lever Operation (Figure 13) to the CLOSED position. If the engine has not started repeat steps 1 through 5. CAUTION - Safety Rules 7. Before the compactor is put into operation run the engine for Make sure to follow all safety rules referenced in the safety 3-5 minutes.
MVC-64H/HW — MAINTENANCE CAUTION - Inspection Intervals CAUTION - Inspection These inspection intervals are for operation under normal Inspection and other services should always be carried out conditions. Adjust your inspection intervals based on the on hard and level ground with the engine shut down. number of hours plate compactor is in use, and particular working conditions.
Page 21
MVC-64H/HW — MAINTENANCE Changing Vibrator Oil 1. When changing the vibrator oil, remove the drain plug (Figure 10), and simply tip the compactor to drain the oil. Note that the oil will drain more easily while it is hot. Remember to use only 10W-30 motor oil when replacing vibrator oil.
MVC-64H/HW — PREPARATION FOR LONG -TERM STORAGE Compactor Storage For storage of the compactor for over 30 days, the following is required: Drain the fuel tank completely or add STA-BIL to the fuel. Run the engine until the fuel in the injection system is completely consumed.
MVC-64H/HW — TROUBLESHOOTING (ENGINE) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, please take a remedial action following the diagnosis based on the Engine Troubleshooting (Table 8) information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult our company's business office or service plant.
Page 24
MVC-64H/HW — TROUBLESHOOTING (ENGINE) r i A r i a e l c o l f s u j , t n - e r d l i l e v . r o " " r e i s s i f s i .
MVC-64H/HW — TROUBLESHOOTING (PLATE COMPACTOR) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, please take a remedial action following the diagnosis based on the Compactor Troubleshooting (Table 9) information shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult our company's business office or service plant.
MVC-64H/HW — EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks QTY. Column used in the Parts section of this manual. Use the help numbers Numbers Used - Item quantity can be indicated by a number, found on the back page of the manual if there are any questions.
MVC-64H/HW — NAME PLATE AND DECALS NAME PLATE AND DECALS PAGE 28 — MVC-64H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (10/20/05)
Page 29
MVC-64H/HW — NAME PLATE AND DECALS NAMEPLATE AND DECALS PART NO. PART NAME QTY. REMARKS PLATE, MODEL/SERIAL NUMBER ..... 1 ....CONTACT PARTS DEPT. 920203290 DECAL, READ OWNERS MANUAL 1 ....NPA-329 920203989 DECAL, BELT GUARD WARNING 1 ....NPA-989 920101410 DECAL: MIKASA MARK 120X60 ......
MVC-64H/HW — MAIN BODY ASSY. (OLD STYLE) MAIN BODY ASSY. (OLD STYLE) PAGE 30 — MVC-64H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (10/20/05)
Page 31
MVC-64H/HW — MAIN BODY ASSY. (OLD STYLE) MAIN BODY ASSY. (OLD STYLE) PART NO PART NAME QTY. REMARKS 418117710 VIBRATORY PLATE ........1 ....S/N L3695 AND BELOW 418216490 BASE ............1 ....S/N L4358 AND BELOW 939010250 SHOCK ABSORBER D45-H41 959404350 EARTH WIRE 020310080...
MVC-64H/HW — MAIN BODY ASSY. (NEW STYLE) MAIN BODY ASSY. (NEW STYLE) PAGE 32 — MVC-64H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (10/20/05)
Page 33
MVC-64H/HW — MAIN BODY ASSY. (NEW STYLE) MAIN BODY ASSY. (NEW STYLE) PART NO PART NAME QTY. REMARKS 418117711 VIBRATORY PLATE ........1 ....S/N L3696 AND ABOVE 418216491 BASE ............1 ....S/N L4359 AND ABOVE 939010254 SHOCK ABSORBER D45-H41 959404350 EARTH WIRE 020310080...
MVC-64H/HW — WATER TANK ASSY. WATER TANK ASSY. PAGE 36 — MVC-64H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (10/20/05)
Page 37
MVC-64H/HW — WATER TANK ASSY. WATER TANK ASSY. PART NO PART NAME QTY. REMARKS 418216510 HOOK 002211025 BOLT 10X25 H, SW 418910020 WATER TANK, ORANGE ......1 ....INCLUDES ITEM W/ 418910030 WATER TANK, WHITE ....... 1 ....INCLUDES ITEM W/ 954300342 CAP, WATER TANK 001241030...
Page 55
HONDA GX120K1SM12 ENGINE — CARBURETOR ASSY. CARBURETOR ASSY. PART NO. PART NAME QTY. REMARKS 16010ZE1812 GASKET SET 16011ZE0005 VALVE SET, FLOAT 16013ZE0005 FLOAT SET 16015ZE0831 FLOAT CHAMBER SET ........1..... INCLUDES ITEMS W/ # 16024ZE1811 DRAIN SCREW SET 16028ZE0005 SCREW SET B 16044ZE0005 CHOKE SET 16100ZH7W51...
HONDA GX120K1SM12 ENGINE — AIR CLEANER ASSY. AIR CLEANER ASSY. PAGE 56 — MVC-64H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #4 (10/20/05)
Page 57
HONDA GX120K1SM12 ENGINE — AIR CLEANER ASSY. AIR CLEANER ASSY. PART NO. PART NAME QTY. REMARKS 16271ZE1000 GASKET, ELBOW 17210ZE0822 CLEANER ELEMENT ......... 1 ... INCLUDES ITEMS W/ # 17218ZE0821 ELEMENT OUTER 17230ZE0820 COVER, AIR CLEANER 17232891000 GROMMET, AIR CLEANER 17235ZE1831 NOSE, SILENCER 17238ZE0010...
TERMS AND CONDITIONS OF SALE — PARTS Effective: October 1, 2002 Parts must be in new and resalable Multiquip reserves the right to quote and sell PAYMENT TERMS condition, in the original Multiquip pack- direct to Government agencies, and to Original Terms of payment for parts are net 10 days.
Page 72
OPERATION AND PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office MQ Parts Department 18910 Wilmington Ave. Tel. (800) 421-1244 800-427-1244 Fax: 800-672-7877 Carson, CA 90746 Fax (800) 537-3927 310-537-3700 Fax: 310-637-3284 Contact: mq@multiquip.com...
Need help?
Do you have a question about the Mikasa MVC-64H and is the answer not in the manual?
Questions and answers