Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fumex C 600HT
Summary of Contents for Fumex C 600HT
- Page 1 Manual C 600HT...
-
Page 2: Table Of Contents
• The correct parameters are indicated on the fan’s Only use original parts and accessories. Repairs under rating plate warranty must be handled by Fumex AB or, subject to • The fan has not sustained damage during transport the manufacturer’s approval, by a third party. The war- •... -
Page 3: Safety
FUMEX C 600HT 2 Safety 2.4 Flying objects Throughout the fan’s life cycle, to prevent personal injury The energy level of the air at the fan outlet and damage to peripherals or the fan itself, strict compli- is extremely high. Particles and small objects... - Page 4 Complex maintenance work (such as removal disconnection of the motor or impeller) must be carried out by Fumex AB or with the latter’s permission, Before starting any work on the fan (e.g. in- in accordance with the latter’s instructions. stallation, maintenance, servicing or dismant-...
-
Page 5: Product Description
FUMEX C 600HT 3 Product Description 3.2.2.1 Area of use The C 600HT fan is intended for the evacuation of ga- 3.1 Serial number and product name ses, smoke and lighter particles with temperatures up to 200 °C. See product nameplate. -
Page 6: Preparation For Use
FUMEX C 600HT 4 Preparation for Use Make sure that there are no loose objects in the vici- nity of the fan and that the fan is securely and safely 4.1 Transport and storage installed (e.g. the cover of the connection box has been correctly fitted and the mounting screws have been tightened). - Page 7 Fig. 5. Other Detailed information about electrical connection can mounting methods require the approval of Fumex AB. be found in the motor documentation and/or on the The mounting points of the fan are at the inlet flange, motor’s rating plate –...
-
Page 8: Commissioning
FUMEX C 600HT 5.2 After 30 minutes of constant operation Fan with TP sensor Some fans are equipped with a bimetal sensor (the Make sure of the following points: TP sensor is mounted near the front ball bearing on • Measured vibration values, with details of the point the electric motor). -
Page 9: Troubleshooting
FUMEX C 600HT 7 Troubleshooting TROUBLESHOOTING GUIDE Symptom Possible cause Damaged impeller. The fan is not mounted fully level. Dirt or other accumulation on impeller that causes imbalance. Other cause of imbalance in the impeller. Parts rubbing against each other. -
Page 10: Maintenance
FUMEX C 600HT 8 Maintenance The maximum value for the vibrations at the motor ball bearing (perpendicular to the motor shaft) must not exceed the values in the table below: Repairs may only be carried out by the manufacturer. We are not liable for repairs carried out by third parties. -
Page 11: Technical Information
(due to e.g. abrasion). • Safety equipment works properly. 9 Technical Information 9.1 Dimensional drawing Fig. 7 9.2 Technical data Model ..... C 600HT-1 C 600HT-3 Voltage: ....1-phase 230 V 3-phase 230/400 V Rated current: ..1,55 A 0,85 A/0,50 A Rated power: ... -
Page 12: Spare Parts
4. Motor shield 8. Temperature barrier, fasteners EXTRACTION ARMS · VEHICLE EXHAUST EXTRACTION · FANS · FILTERS · CURTAINS · CONTROLS Verkstadsvägen 2, 93161 Skellefteå, Sweden • Tel.: +46 910-361 80 • Fax: +46 910-130 22 • E-mail: info@fumex.se www.fumex.com...
Need help?
Do you have a question about the C 600HT and is the answer not in the manual?
Questions and answers