Advertisement
Quick Links
DOME LENS PIR MOTION SENSOR LED LIGHT
Specifications:
1. Power: 220-240V~ 50Hz.
2. Range of detection: Adjustable from 2m to 10m.
3. Angle of detection: 240°
4. Timer: Adjustable from 3 sec. to 15 min.
5. Lux control: Adjustable "Light level" sensing
from 5 Lux to 1000 Lux and Test Mode.
6. Lamp type & output load:
Model No.
SLRF13W
SLRF13B
SLRF26W
SLRF26B
Adjustments:
NOTE: Pull the sensor head surround down to reveal the adjustment knobs. After setting, push
it back to position. (Figure A)
1. TIME: The time can be set variably from 3 sec, 15 sec, 30 sec, 1 min, 3 min, 5 min, 10 min
to 15 min. Timer starts counting from the latest detected movement. While there is still
movement in the detecting area, the lighting will remain on and the timer will keep resetting.
(Figure B)
SLRF13W/SLRF13B
SLRF26W/SLRF26B
Lamp Type
CREE COB 13W x 1 pc
1000 lm / 5000K
CREE COB 13W x 2 pcs
2000 lm / 5000K
Figure B
SLRF13W
SLRF13B
Output Load
230VAC / 800W / cosφ=1
230VAC / 400VA / cosφ=0.5
200VA
LED 200VA
Figure C
1
SLRF26W
SLRF26B
Figure A
Figure D
Advertisement
Related Manuals for Challenger SLRF13W
Summary of Contents for Challenger SLRF13W
- Page 1 SLRF13W/SLRF13B SLRF26W/SLRF26B DOME LENS PIR MOTION SENSOR LED LIGHT Specifications: 1. Power: 220-240V~ 50Hz. 2. Range of detection: Adjustable from 2m to 10m. 3. Angle of detection: 240° 4. Timer: Adjustable from 3 sec. to 15 min. SLRF13W SLRF26W 5. Lux control: Adjustable “Light level” sensing...
-
Page 2: Manual Override
The recommended installation height is 1.8~2.2m. The sensor has a range of detection of 10m at 20°C, adjustable from 2m to 10m (Figure C). The sensor head can be rotated left and right 90° horizontally. SLRF13W/SLRF13B/SLRF26W/SLRF26B has a detecting angle of 240°. (Figure E) Ideal height 2.2m... -
Page 3: Installation
6. Lamp head: The lamp head can turn 90° horizontally and 50° vertically allowing for optimum illumination. 50° 90° Installation: Warning: This product must be installed only by a qualified electrician. Installation must follow local building codes as well as the instruction contained in this manual. -
Page 4: Installation Hints
Installation hints: To ensure the best performance of your sensor, refer to the following figures for an ideal location. AIM SENSOR DOWNWARD TO REDUCE MOUNT ON STABLE SURFACE RANGE AVOID REFLECTED LIGHT FROM DON'T EXPOSE TO RAIN OR BRIGHT SURFACES ROOF RUNOFF MORE SENSITIVE TO MOVEMENT POSITION SENSOR EXACTLY LEVEL... -
Page 5: Initial Set Up And Operation
Initial set up and operation: 1. After connection to mains power, 60 seconds is required to warm up. The lighting lasts approximately 60 seconds. 2. Walk in front of the detector until the light comes up. This checks the operation of the detector and the field of view. - Page 6 Due to our policy of continuous improvement we reserve the right to change specification without prior notice. Errors and omissions excepted. These instructions have been carefully checked prior to publication. However, no responsibility can be accepted by Challenger for any misinterpretation of these instructions.