Table of Contents
Advertisement
Quick Links
CHASSIS
4124
OPERATOR'S MANUAL
READ AND UNDERSTAND THIS MANUAL
BEFORE OPERATING THIS EQUIPMENT.
UNSAFE OPERATION OR MAINTENANCE OF
WARNING
THIS EQUIPMENT CAN RESULT IN SERIOUS
INJURY OR DEATH.
Starting Serial #611001
HSMFG0516
Part #72824
Manufactured By
H&S MANUFACTURING CO.,INC.
P.O. BOX 768 (715) 387-3414 FAX (715) 384-5463
MARSHFIELD, WISCONSIN 54449
Advertisement
Table of Contents
Related Manuals for H&S 4124
Summary of Contents for H&S 4124
- Page 1 CHASSIS 4124 OPERATOR’S MANUAL READ AND UNDERSTAND THIS MANUAL BEFORE OPERATING THIS EQUIPMENT. UNSAFE OPERATION OR MAINTENANCE OF WARNING THIS EQUIPMENT CAN RESULT IN SERIOUS INJURY OR DEATH. Starting Serial #611001 HSMFG0516 Part #72824 Manufactured By H&S MANUFACTURING CO.,INC. P.O. BOX 768 (715) 387-3414 FAX (715) 384-5463...
-
Page 2: Table Of Contents
CONTENTS Warranty & Warranty Registration Card........1-2 Manufacturers Statement . -
Page 5: Dealer Pre-Delivery Checklist
H&S DEALER PRE-DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS After the Chassis has been completely set-up, check to be certain it is in correct operating order before delivering to the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments and found the item operating satisfactorily. - Page 6 Intentionally Left Blank...
-
Page 7: Dealer Delivery Checklist
DEALER DELIVERY CHECK LIST AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS This check list that follows is an important reminder of valuable information that should be passed on to the customer at the time this Chassis is delivered. Check off each item as you explain it to the customer. - Page 8 Intentionally Left Blank...
-
Page 9: Safety Information - Be Alert Symbol
SAFETY INFORMATION YOUR SAFETY ALERT! IS INVOLVED. THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY IS INVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONS MUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE. -
Page 10: Safety Information - Explanation Of Safety Signs
SAFETY INFORMATION Keep signs in good condition. Immediately replace any missing or damaged signs. RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury. Follow recommended precautions and safe operating prac- tices. -
Page 11: Safety Instructions
FOLLOW SAFETY INSTRUCTIONS Carefully read all safety messages in this manual and all safety signs on the machine. Follow recommended safety precautions and safety operating practices. Keep safety signs in good condition. Replace missing or damaged safety signs. RUN-AWAY / BREAK AWAY WARNING: TO PREVENT SERIOUS INJURY OR DEATH Shift to lower gear before going down steep grades. -
Page 12: Mount Attachments Safely
MOUNT ATTACHMENTS SAFELY CAUTION: When mounting equipment to the chassis, refer to the manufacturer’s mounting recommendations for that particular equipment. WARNING: Help prevent serious injury of death resulting from tractor or chassis rollover. Travel uphill or downhill when working on inclines or slopes, avoid traveling across the grade. -
Page 13: Safety Decals
SAFETY INFORMATION -11-... - Page 14 TRACTOR; This operators manual uses the term “Tractor” when identifying the the power source. W A R N I N G TO PREVENT SERIOUS INJURY OR DEATH BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWING INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
- Page 15 -13-...
-
Page 16: Set-Up & Assembly
SET-UP & ASSEMBLY NOTE: Determine right or left side of the Chassis by viewing it from the rear. If instructions or parts lists call for hardened bolts, refer to bolt torque chart. 1. Check the Chassis for proper assembly and adjustment. 2. - Page 17 Intentionally Left Blank -15-...
-
Page 18: Transporting
TRANSPORTING TOWING ON HIGHWAY Follow state and local regulations when towing farm equipment on public highways. Never tow the chassis on a public highway at a speed greater than 20 mph (32 kph). SAFETY CHAIN To prevent break-away, always use a safety chain when attaching to the towing vehicle.The safety chain shall have a minimum tensile strength equal to, or greater than the ultimate gross weight of the towed machine. -
Page 19: Operation
OPERATION GENERAL INFORMATION After receiving your chassis, check entire unit carefully before first operation. Tighten bolts and set screws that might have come loose. Lubricate as explained in the Lubrication Chapter in this manual. WHEEL BOLTS Tighten wheel bolts to specifications below after chassis has been in use for a short period of time. Check periodically thereafter. -
Page 20: Adjustment
ADJUSTMENTS WHEEL BEARINGS IF WHEEL BEARINGS BECOME LOOSE, ADJUST THEM IMMEDIATELY. Block wheels to prevent rolling, jack up chassis until wheels turn freely. Remove hub cap Remove cotter pin (B) from adjusting nut and spindle. Tighten hub nut (A) until there is a slight drag on hub when wheel is turning. Check cotter pin hole location on spindle, back nut off one notch on nut, re-insert cotter pin Replace hub cap, and lower to the ground. -
Page 21: Service
SERVICE Your H&S Chassis has been designed and manufactured to provide years of trouble free service. You the operator, can help by performing the following: FREQUENTLY: * Check wheel bearings, making sure of proper adjustment (See instructions above). * Check lug nuts. Be sure all are tightened to specifications prior to operation. * Check tire pressure. -
Page 22: Options
OPTIONS ELECTRIC-OVER-HYDRAULIC BRAKES The brake system is electric-over-hydraulic (brake fluid) only. The controller must be located on the tractor for the brakes to operate. If the tractor is set up with the #4 pin in the seven in plug as being brakes (per new ASABE standard) it will be activated when the user pushes the brake pedal. -
Page 23: Lubrication Guide
LUBRICATION Become familiar with all lubrication points and establish a routine to ensure complete lubrication of the Chassis. GENERAL INFORMATION If lubricated properly and often enough, it will prolong the life of your Industrial Chassis. Grease daily during normal use and before and after storage and after power washing. Use a good grade of Lithium-base grease. -
Page 24: Decal Location
Patent Decal 1495A Run-Away/Break-Away Hazard 72859 H&S/Model Right Side 72861 H&S/Model Rear & Left Side 72865 4124 Model Number 54033 Made in the U.S.A. 71188B Jack Storage Position 72203A Warning - Help Avoid Injury 82602 Crushing Hazard(One on each side of Tongue) - Page 25 DECAL LOCATION 72859 72865 82602 82602 72865 72861 093020 54033 71188B -23-...
- Page 26 DECAL LOCATION 1495A 91604 72203A 72861 -24-...
-
Page 27: Service Notes
SERVICE NOTES _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _______________________________________ _________________________________________ ___________________________________________... - Page 28 SERVICE NOTES _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _______________________________________ _________________________________________ ___________________________________________...
- Page 30 H&S MFG H&S MFG ..CO H&S MFG CO ..H&S MFG H&S MFG products approved for the FEMA FEMA FEMA FEMA FEMA SEAL OF Q SEAL OF Q U U U U U ALITY SEAL OF Q ALITY ALITY...