Subscribe to Our Youtube Channel
Related Manuals for Worx Nitro WX840.X Series
Summary of Contents for Worx Nitro WX840.X Series
- Page 1 SAFETY AND OPERATING MANUAL ORIGINAL INSTRUCTIONS 20V Cordless 18 gauge Nail/ WX840 WX840.X Staple Gun...
- Page 3 PRODUCT SAFETY moment of inattention while operating power tools may result in serious personal injury. GENERAL POWER TOOL eye protection. Protective equipment such as dust SAFETY WARNINGS mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will WARNING: Read all safety warnings and all reduce personal injuries.
-
Page 4: Nailer Safety Warnings
SAFETY WARNINGS FOR in accordance with these instructions, taking into account the working conditions and the BATTERY PACK work to be performed. Use of the power tool for operations different from those intended could a) Do not dismantle, open or shred cells or battery result in a hazardous situation. - Page 5 Warning RCM marking ABN: Australian Business Number. Wear ear protection By this number, business information such as entity type, status, business location etc. can be found at website Wear eye protection ABN of Positec Australia Pty Limited is 14 101 682 357 Wear dust mask Make sure the battery is removed prior to changing accessories...
- Page 6 20V Cordless 18 gauge Nail/ WX840 WX840.X Staple Gun...
- Page 7 20mm 25mm 32mm 35mm 38mm 40mm 45mm 50mm 20V Cordless 18 gauge Nail/ WX840 WX840.X Staple Gun...
- Page 8 5.7mm 19mm 25mm 32mm 38mm 40mm 20V Cordless 18 gauge Nail/ WX840 WX840.X Staple Gun...
- Page 9 20V Cordless 18 gauge Nail/ WX840 WX840.X Staple Gun...
-
Page 10: Component List
COMPONENT LIST changes between these models. *** Voltage measured without workload. Initial NO-MAR PAD battery voltage reaches maximum of 20 volts. WORKPIECE CONTACT Nominal voltage is 18 volts. DRIVE DEPTH ADJUSTMENT SUGGESTED BATTERIES ON/OFF SWITCH AND CHARGERS LED WORKLIGHT SWITCH INDICATOR LIGHT Category Type... - Page 11 WARNING: The vibration emission value during Installing the belt hook actual use of the power tool can differ from the NOTE: The belt hook can be declared value depending on the ways in which the tool See Fig. B installed on the left or right side is used dependant on the following examples and other of the nail gun.
-
Page 12: Maintenance
LED worklight NOTE: The LED Worklights provide feedback to indicate See Fig. G whether the battery pack is tool is functioning properly. Removing a jammed nail Try to operate the tool for two jammed. WARNING: Always remove the battery pack •... -
Page 13: Troubleshooting
TROUBLESHOOTING Symptom Possible Causes Possible Solution Tool does not operate properly: Tool is overheat Wait until the tool cools down green light on No nails Replenish nails Jammed nails Removing a jammed nail red light on Low battery Recharge battery Tool operates properly, but fasteners Depth of drive isn’t deep enough Adjust depth of drive... -
Page 14: Declaration Of Conformity
DECLARATION OF CONFORMITY Positec Germany GmbH Postfach 32 02 16, 50796 Cologne, Germany On behalf of Positec declare that the product Description WorxNITRO Cordless Nail Gun Type WX840 WX840.X (840 - designation of machinery, representative of nail gun) Function Fastening various materials Complies with the following Directives: 2006/42/EC 2014/30/EU... - Page 15 DECLARATION OF CONFORMITY Positec (UK & Ireland) Ltd. PO Box 6242, Newbury, RG14 9LT, UK Declare that the product Description WorxNITRO Cordless Nail Gun Type WX840 WX840.X (840 - designation of machinery, representative of nail gun) Function Fastening various materials Complies with the following regulations: Supply of Machinery (Safety) Regulations 2008 Electromagnetic Compatibility Regulations 2016...
- Page 16 After-sales Service and Application At www.worx.com you can order spare parts or arrange the collection of a product in need of servicing or repair. Tel. Service: 0345 202 9679 E-Mail: customerservices@worxtools.com www.worx.com Copyright © 2022, Positec. All Rights Reserved. AR01481205...
Need help?
Do you have a question about the WX840.X Series and is the answer not in the manual?
Questions and answers