Related Manuals for Total TWP775016
Summary of Contents for Total TWP775016
- Page 1 SUBMERSIBLE PUMP TWP775016 TWP7110016 TWP775016-5 TWP7150026 UTWP7150026 TWP7150026-5 SCAN FOR VIDEO SCAN FOR VIDEO TOTAL TOOLS WORLD...
-
Page 2: General Points
1 GENERAL POINTS Read this documentation carefully before installation. Installation and functioning must comply with local and national safety regulations in force in the country where the product is to be installed. The entire operation must be carried out in a workmanlike manner. Failure to comply with the safety regulations not only causes risk to personal safety and damage to the equipment, but also invalidates any right to warranty assistance. - Page 3 5 MANAGEMENT 5.1. STORAGE All the pumps must be stored indoors. in a dry. vibration-free and dust-free environment, possibly at constant air humidity. They are supplied in their original packaging and must be kept there until installation. 5.2. TRANSPORT Avoid subjecting the products to needless jolts or collisions. The electro pumps must never be carried or lifted by their power cables.
-
Page 4: Site Of Installation
7 INSTALLATION 7.1 SITE OF INSTALLATION Before immersing the electro pump in the pit or tank, ensure that the place is free from sand or solid sediment. In case there is sediment, accurately clean the site where it is to be placed. ... -
Page 5: Electrical Connections
8 ELECTRICAL CONNECTIONS CAUTION! ALWAYS FOLLOW THE SAFETY REGULATIONS! 8.1 The electrical installation must b e carried out by an authorized and competent electri- cian who assumes all the responsibilities. 8.2 Ensure that the mains voltage is the same as shown on the plate of the motor to be fed and be sure TO MAKE A GOOD GROUND CONNECTION. - Page 6 8.4 CHECKING THE DIRECTION OF ROTATION (for three-phase motors) Fig.2 CAUTION! ALWAYS FOLLOW THE SAFETY REGULATIONS The direction of rotation must be checked each time a new installation is carried out. Proceed as follows: 1. Place the pump on a flat surface. 2.
-
Page 7: Maintenance And Cleaning
9.2 FLOAT SWITCH SETTING By lengthening or shortening the stretch of cable between the float and the fixed point (Float locking) it is possible to regulate the level at which the pump switches off. Ensure that the float witch can move freely when the pump is operating. Make sure the stop level does not uncover the filter. - Page 8 13 TROUBLESHOOTING FAULT CHECK (Possible cause) REMEDY The motor does not start Make sure motor is live and check If they are burnt-out, change and makes no noise. that the mains voltage corresponds them. to the one on the data plate. Check the protection fuses.
-
Page 9: Technical Data
The appliance, its packaging and accessories are all produced from recyclable materials and must be disposed of accordingly, in the suitable dispose places, adhering itself to the modalities previewed from the enforced norms in matter. 14 TECHNICAL DATA Model No. TWP775016 TWP775016-5 TWP7110016 TWP7150026 UTWP7150026... - Page 10 TWP775016,TWP7110016,TWP775016-5 Exploded view...
- Page 11 TWP775016,TWP7110016,TWP775016-5 Part Description Part Description Tie rod Stator Stretching washer Undulated washer Washer Bearing Bolt Rotor Washer Bearing Handle Screw Washer Protector Connection part Cable presser Mechanical seal Washer O ring Screw Oil chamber cover Bolt Screw O ring Washer...
- Page 12 TWP7150026,UTWP7150026,TWP7150026-5 Exploded view...
- Page 13 TWP7150026,UTWP7150026, TWP7150026-5 Spare part list Part Description Part Description Protector Casing Float switch O ring Bolt Screw Cable presser Washer Screw Oil chamber Handle Mechanical seal Screw O ring Cable presser Oil chamber cover Cable Oil seal Screw O ring O ring Screw Tie rod...
- Page 14 SUBMERSIBLE PUMP www.totalbusiness.com TOTAL TOOLS CO., PTE. LTD. No. 45 Songbei Road , Suzhou Industrial Park , China. MADE IN CHINA T0821.V05...
Need help?
Do you have a question about the TWP775016 and is the answer not in the manual?
Questions and answers