Statement Thank you for purchasing your new greenhouse. We recommend you familiarize yourself with the instruc- tions and read all safety information before you commence assembly. The assembly instructions mainly consist of detailed illustrations and no specific technical knowledge is required for the assembly of the greenhouse.
Important Before assembling your new greenhouse, please check that all parts in the provided list are included. Please take each bundle out of the packaging in order to identify the parts better. Most parts are numbered and can be identified by a stamped number or removable label. Alternatively, the components can be iden- tified by lengths detailed in the packing list (see diagram below).
Page 4
Base We cannot emphasis how important it is to have a proper base for your Greenhouse to be erected upon. It is essential that the BASE IS FLAT, LEVEL AND SUBSTANTIAL enough to take the weight of the greenhouse including its polycarbonate panels or heavy glass. Give yourself enough room around your base to allow for fitting the polycarbonate panel or glass and any ongoing maintenance / cleaning.
Page 6
Side Gable 6319 6324 6901 6611/6811 6611/6811 6324 6901 6320/ 6321 6320/ 6321 6906/ 6319 6908 6320/ 6321 6917/ 6324 6918 6901 Note: At this stage, if you al- ready decide where your vent positioned, 6917/ please insert two extra 6918 bolts into each side bar (#6319) either side of a...
Page 10
Front wall 6903/ 6905 6926 6922 6801 6801 6903/ 6905 6927 6927 6926 6903/ 6905 6927 6923 6926 6922 6924/ 6925 6930 6923 6924/ 6922 6925 6930 6930 6903/ 6905 Please insert fluff into the channel of ridge bar (#6930) before it connect to side corner bar (#6903/6905) and roof corner bar (#6906/6908).
Page 13
Vent Section View 6936 6936 Please insert vent top bar (#6336) into vent ridge bar (#6936) first before locating vent system in posi- 6336 tion. 6319 6936 Maybe you should swing vent ridge bar (#6936) to match the extra bolt in side bar (#6319) which inserted in ad- vance.
Page 14
Package 6 Door 6937 6938 6939 6940 6941 6942 2444 1864 1864 1864 M6x10 FLUFF Φ3.5x19 Φ3.5x35 M4x8 M3x10 3.8M 1000 6938 6938 6940 6940 6941 6942 6940 6938 6939 6939 6940 6939 6939 6939 6939 6939 6940 6940 6941 6942 6939 m11 is magnetic door lock, every center door vertical bar...
Page 15
Door 6923 6937 6937 6923 6937 6937 6937 6937 Bracket (m22) was used to connect door track bar (#6937) and corner bars. Please assemble bracket (m22) on door track bar (#6937) first before connect- ing door track bar to horizontal bar (#6923). 6801 6937 p5 is door track cover...
Page 16
Package 7 Louver M6x10 Φ3.5x19 Crop GS..93 Installation of Louver(Only for GS010993 Model) Place top sill into position on side jamb of louvre and secure with self tapping screws. * Do same with bottom sill. * Please note that the handle is on the right hand side. The diagrams are viewed from inside. *...
Page 17
Please cut 20mm long rubber gib part #p10 to fill in the gap between glass and aluminium frame from greenhouse inside. 4 gibs every glass panel, at 4 corners. (One meter long rubber gib in Door Package)
Page 18
Glass Foam On front and rear gable and side wall GS010993 GS010994 Please put foam together with masking paper on glazing bar first, then peel off masking pa- FOAM per from foam before assembling glass panels. roll roll...
Page 20
—— Use PVC Bar Capping Glass GS..94 GS..93 GS..94 GS..93 Length Length Front Gable 1901 Glass Rear 1598 Gable Side Glass Glass 1598...
Page 21
Polycarbonate Panel —— Use PVC Bar Capping GS010994 GS010993 Length GS..94 GS..93 Size GS..94 GS..93 1276 596x1272 Roof 596x964 596x1596 1580 PVC Capping Bar Step6 Step1 Panel Step3 Step4 Step2 Note: Step5 PVC capping bars were Panel pushed in place from both top and bottom in diagonal direction to- gether.
Page 23
The list of parts Description GS010994 GS010993 Side Rear Front Roof Vent Door Louver Polycarbonate panels or Glass Tools Assembly Instruction...