Advertisement
do Not use the light near flammable, combustible or explosive liquids, solids, gases or equipment.
8
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a
9
safe, dry, childproof location.
2. iNtRoductioN
tungsten/halogen tubes mounted in die-cast alloy heads. The light units are supported on a telescopic pole with locking rings. Folding tripod feet
can be secured in two positions on the base, allowing compact storage when not in use. All lamps are supplied with 1.8mtr lead and fitted with a
BS approved plug.
3. specificAtioN
model no: ................................................................ml1000d
Power: ....................................................................400W (x2)
lumen output: .......................................................... 17090lm
input: ..............................................................................230V
max. height: ......................................................... 0.95/1.8mtr
replacement bulb: ....................................................ML400B
4. AsseMblY
Refer to attached parts list.
4.1.
fit bulbs.
4.1.1.
undo screw (3) on top of each lamp.
4.1.2.
fit bulb to each. do Not touch the bulb as the natural oil from hands
will shorten bulb life. Handle with a dry clean cloth only.
4.1.3.
Refit screw.
4.2.
Attach lamps to cross member (38).
4.2.1.
use thread screw (34) washer (35) and nut.
4.3.
fit handles (14) to the top of each lamp, use nut (15).
4.4.
Unfold all three legs to the same angle first. Pull lock bar at the top of
each leg towards the bottom end of the leg to release, and unfold to
desired angle.
4.5.
Bolt cross member (38) and lamps to the small tube (47).
4.6.
use thread screw (34) and washer (35).
terminal block (41) hangs from small tube thread screw (34).
5. opeRAtioN
5.1.
Adjust height by undoing lock collar on each section. Re-tighten lock collar.
5.2.
Avoid touching the glass shield (5) as handling may reduce service life
and cause the glass to crack.
6. MAiNteNANce
Remove from power supply before attempting maintenance.
6.1.
clean with a dry lint free cloth. clean the glass shield (when cold) with
alcohol and a soft cloth. if the glass is damaged replace immediately.
do Not use without the glass shield or the weather seal.
8
6.2.
Although weatherproof do Not store wet. unplug from the mains and
dry before storing.
6.3.
renew bulb.
WARNiNg! remove from the power supply and allow to cool before
‰
touching the unit.
do Not touch the bulb as the natural oil from hands will shorten bulb life. Handle with a dry clean cloth only.
8
6.3.1.
Undo screw (3) on top of lamp, renew bulb, refit screw.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
Weee Regulations
dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic
Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way.
contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMpoRtANt: no liability is accepted for incorrect use of this product.
WARRANtY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, Suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7AR
Original Language Version
01284 757500
01284 703534
mL1000D.V3 | Issue 2(I) 18/10/16
www.sealey.co.uk
Web
sales@sealey.co.uk
Advertisement
