Related Manuals for InstaRobo L1
Summary of Contents for InstaRobo L1
- Page 1 L1 Robot Vacuum Cleaner User Manual © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 2 © 2021 InstaRobo. All rights reserved. www.instarobo.com...
-
Page 3: Table Of Contents
Contents Safety Instructions Product Description Preparations App Networking Modes Function Description Product Maintenance Troubleshooting Product Specifications Safety Information © 2021 InstaRobo. All rights reserved. www.instarobo.com... -
Page 4: Safety Instructions
11. Do not burn the product even if it is severely damaged, because the battery built in it may 20. Reclaim the abandoned battery. cause explosion. 21. Do not use the mopping function on the carpet. © 2021 InstaRobo. All rights reserved. www.instarobo.com... - Page 5 Product Components and Accessories Main unit Charging dock Power adapter Brush Dust box Water tank HEPA filter Side brush x2 Instructions Manual © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 6 * Press the button to start or pause cleaning Recharge button * Press the button to start or pause charging Omnidirectional lens Dust box button Charging electrode Cliff sensor Omnidirectional wheel Battery Side brush Driving wheel Roller brush assembly Dust box © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 7 Dust box HEPA filter Filter cover Primary filter Dust box conductive shrapnel Dust box side cover Water tank Charging dock Signal indicator Water inlet Water tank main body DC connector Mopping cloth Charging electrode © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 8 © 2021 InstaRobo. All rights reserved. www.instarobo.com...
-
Page 9: Preparations
Preparations for Unpacking Before you use the main unit, remove the protective strip from the main unit and remove the protective film from the charging dock. [Remove the protective strip] [Remove the protective film] © 2021 InstaRobo. All rights reserved. www.instarobo.com... -
Page 10: App Networking Modes
Wi-Fi list, and tap Go to Connect. 5. After the connection is set up, the Tuya app shows the connection screen. You can control the product after a connection success message is displayed. © 2021 InstaRobo. All rights reserved. www.instarobo.com... - Page 11 When this icon is steady on, the vacuum cleaner automatically returns to the docking station for charging. When this icon blinks, the vacuum cleaner stops returning to the docking station. No-go zones Set a restricted zone for cleaning. Partition Editing © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 12 Place the charging dock on a hard surface against the wall, rather than on a carpet or woolen blanket. 2. Keep the charging dock in the powered state. Otherwise, the auto recharge function does not take effect. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 13 After the power is sufficient, the main unit will automatically return to the interrupted point to resume cleaning (ensure that you have enabled the resumable cleaning function). Zone 4: Zone 3: To be cleaned Is being cleaned © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 14 1.If the vacuum cleaner fails to find the docking station, it automatically returns to the starting point. 2.In this case, you need to manually put the vacuum cleaner back to the docking station. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 15 If you activate partial cleaning when the vacuum cleaner is paused, the lost. previous cleaning task will be terminated. 1.6 m mopping Virtual wall zone Cleaning zone © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 16 You can use the mobile app to select the cleaning strength: Energy-saving, Standard, or Turbo. The Standard cleaning mode is selected by default. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 17 2. Add water. 1. After mopping is completed, empty the water tank in a timely manner ！ and then remove and clean the mopping cloth. 2. Do not use the mopping function on the carpet. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 18 Every three to six months (or upon obvious damage of the Roller brush cover Every month rubber silicon strip on the roller brush cover) Not required Sensor Every month Not required Charging electrode Every month Not required Omnidirectional wheel Every month © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 19 Flush the primary filter with water. Open the dust box cover and take out the primary filter Wipe the dust box clean with duster cloth. and HEPA filter. ！ Do not flush the dust box with water. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 20 1. Remove the water tank component. 4. Clean the mopping cloth. 2. Remove the mopping cloth. 5. Dry the mopping cloth. 3. Empty the water tank. 6. Wipe or dry the water tank in the air. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 21 As shown in the following figure, pull the release film to unlock the roller brush cover. Lift the roller brush to remove it. Use the cleaning brush to clean the roller brush. Reinstall the roller brush. Install the roller brush cover. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 22 Side Brush Cleaning 1. Hairs and dirt are prone to attach the side brushes, so you must periodically clean the side brushes. 2. Wait until the side brushes are completely dry before you install and use them. Remove the side brushes. Release and clean hairs tangling the side brushes.
- Page 23 Side Brush Replacement Side brushes may be bent or damaged after being used for a period of time. You are advised to replace side brushes every three to six months or when they are severely damaged. Remove old side brushes and install new ones according to the following figures. ©...
- Page 24 Use dry duster cloth for the cleaning. To protect the charging dock against damages caused by water, do not use wet duster cloth. 3. Clean the driving wheel and omnidirectional wheel. 1. Clean the cliff sensor. 2. Clean the charging electrode. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
-
Page 25: Troubleshooting
Error 12: The top cover of laser is blocked or stuck. The laser head pressure sensor is pressed or stuck. Please move the vacuum cleaner to a different position and restart it. Please check. © 2021 InstaRobo. All rights reserved. www.instarobo.com... - Page 26 1. The dust box is full. Clean the dust box. The cleaning performance degrades, 2. The filter is blocked. Clean the filter. or dust drops from the device. 3. The roller brush is entangled with foreign objects. Clean the roller brush. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
- Page 27 In this case, manually put the robot vacuum cleaner back to the docking station. The vacuum cleaner misses some areas The wall sensor or cliff sensor may get dirty. In this case, wipe the sensors using soft dry cloth. while cleaning. © 2021 InstaRobo. All rights reserved. www.instarobo.com...
-
Page 28: Product Specifications
Cleaning time About 150 minutes Rated power (W) Main unit Operating voltage (V) 14.4 As continuous product optimization is required, the product actually delivered prevails. Tuya reserves the right to update the product. © 2021 InstaRobo. All rights reserved. www.instarobo.com... -
Page 29: Safety Information
X: Indicates that the content of the hazardous substance in a homogeneous material of the part is beyond the limit requirements specified in the currently valid version of GB/T 26572. No mature alternative solutions that meet the environmental protection requirements of the EU RoHS directive are available in the industry. © 2021 InstaRobo. All rights reserved. www.instarobo.com... - Page 30 Shenzhen InstaRobo Innovation Co. , Ltd Room 411, Kingson Building, New Energy Innovation Industrial Park, No.1 Chuang Sheng Road, Nanshan District, Shenzhen, P. R. China After-sales service Email:hello@instarobo.com WhatsApp...