Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Cruisers Yachts DLS CRUISE CRPP-2.6
- Page 1 User manual Seat / Skoda / VW...
-
Page 2: Table Of Contents
CRPP-2.6 Content Welcome to DLS! Welcome Thank you for buying a DLS Cruise CRPP-2.6. For us, it’s all Pre installation about the sound experience. We care deeply about sound and construction quality. In order for your experience to be as optimal as possible, it is important that you fully read this Dismounting door panel manual, preferably before you start your installation. -
Page 3: Pre Installation
Installation Included products: 2pcs Woofer 2pcs Tweeter Start the dismount 2pcs Crossover Dismount the front door by removing the cover of Included in box: the door panel. Hint: Use plastic PRY tools to avoid marks on 2pcs Tweeter connection the panels and destroy the plastic clips. 4pcs Adhesive foam for wrapping 4pcs Terminal crimp connectors 2pcs Four-leaf clover foam for tweeter... -
Page 4: Removing Woofer
Use a 4mm drill to remove the rivets. Make sure Usually a wrench, size 10, will be needed. Norm- all remains from the old rivets are removed from ally the bolt is located at the underside of the door. the inside of the door. When the door panel is loose, start with softly lifting it straight up, to remove the panel. -
Page 5: Removing Tweeter
Change Tweeter Locate the tweeter - Either in the A-pillar, by the side mirror or in same case in the door by the handle. A-Pillar Side mirror Door Dismount over and remove the covers. Use Plastic PRY tools and be careful, there can be air-bags behind the A-pillar. -
Page 6: Changing Tweeter
Remove the old tweeter Use a cutting nipper or a Snap-off blade knife to remove the top of the plastic pin that holds the tweeter. Don’t remove the whole pin, just the top! Change the tweeter, and place it where the OEM tweeter used to be. Make sure that the DLS tweeter is properly fixed. -
Page 7: Crossover
Connect the crossover with the PnP connector. Use the other adhesive foam to secure the crossover and cables The yellow cables are a jumper for decreasing the tweeter level 4dB Finally Start assembling the covers again to finish the work. Make sure that no screws or clips are left over, Reconnect the battery/power source terminal. -
Page 8: Specification Woofer
Specifications Art. no CK-CRPP-2.6 DLS DRIVE CRPP-2.6 Tweeter Woofer 6.5” /165 mm with glass fiber cone Technical Specifiaction: Tweeter 1” / 25 mm silk dome tweeter with accessories Size 1” /2.54 mm RMS Power 100 W RMS Power 50 W MAX Power 200W MAX Power 100W... -
Page 9: Compatible Car Models
Impedance VS Frequency... - Page 10 DLS Cruise CRPP-2.6 compatible car models Model Year Front kit Rear kit AMAROK 2010-2021 CRPP-2.6 CRPP-2.6* NEW BEETLE 1997-2011 CRPP-2.6 BORA 1998-2005 CRPP-2.6 CRPP-2.6* BORA VARIANT 1999-2005 CRPP-2.6 CRPP-2.6* C-Trec 2016-2021 CRPP-2.6 CRPP-2.6* CADDY 2020-2021 CRPP-2.6 CRAFTER II 2017-2021 CRPP-2.6...
-
Page 11: Product Markings
Product markings The crossed-out wheelie bin symbol means that the product, literature and pac- kaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling.
Need help?
Do you have a question about the DLS CRUISE CRPP-2.6 and is the answer not in the manual?
Questions and answers