EMC2 VNXe 3300 System Hardware Installation Manual

For telco racks

Hide thumbs

Table of Contents

Quick Links

Download this manual

EMC

VNXe™3300 System

Hardware Installation Guide

for Telco Racks

300-012-893

P/N

REV 02

This document explains the installation procedures for an EMC VNXe3300

system in a Telco rail self-supporting rack, and describes the kits available

for mounting the devices in a VNXe3300 system. These kits are for Telco rail

only.

self-supporting racks

Introduction ............................................................................................. 4

VNXe3300 system devices .................................................................. 4

◆

Telco rail self-supporting rack .............................................................. 4

◆

Device placement guidelines .................................................................... 5

Position in rack ................................................................................... 5

◆

Device dimensions .............................................................................. 5

◆

Power considerations .......................................................................... 5

◆

Installing a VNXe3300 DPE in a Telco rack................................................. 7

VNXe3300 DPE mounting kit (DPE-TELCO-3U/3US)............................... 7

◆

Installing VNXe3300 DPE mounting trays ............................................. 8

◆

Installing the VNXe3300 DPE in the mounting trays ............................. 9

◆

Installing a 3U DAE in a Telco rack........................................................... 12

3U DAE mounting kit (FRAME-T-PDAE/PDAES) .................................... 12

◆

Installing 3U DAE mounting trays....................................................... 13

◆

Installing the 3U DAE in the mounting trays ....................................... 15

◆

Installing a 2U DAE in a Telco rack........................................................... 17

2U DAE mounting kit (FRAME-T25DAE/T25DAES) ............................... 17

◆

Installing 2U DAE mounting trays....................................................... 18

◆

Installing the 2U DAE......................................................................... 20

◆

Table of Contents

Need help?

Do you have a question about the VNXe 3300 System and is the answer not in the manual?

Questions and answers

Summary of Contents for EMC2 VNXe 3300 System

Page 1: Table Of Contents
® VNXe™3300 System Hardware Installation Guide for Telco Racks 300-012-893 REV 02 This document explains the installation procedures for an EMC VNXe3300 system in a Telco rail self-supporting rack, and describes the kits available for mounting the devices in a VNXe3300 system. These kits are for Telco rail only.
Page 2: Introduction
Introduction Introduction ® This section lists the EMC VNXe™3300 system enclosures currently supported in Telco rail self-supporting racks (Telco racks) and provides an illustration of a typical rack. VNXe3300 system devices EMC offers Telco rack mounting kits for the following VNXe3300 system devices. Kit part Device Mounting kit...
Page 3: Device Placement Guidelines
Device placement guidelines Device placement guidelines Before attaching the mounting trays to the Telco rack, you must decide where to put them. Where you install the devices depends on the kinds of devices that you will install. Devices with internal cooling fans that move air from front to back (or vice versa) and not Position in rack from beneath or above have no special cooling requirements that direct placement in the rack.
Page 4 Device placement guidelines 4 PDUs, 2 per circuit Figure 2 Typical high-availability wiring configuration (AC) EMC VNXe™3300 System Hardware Installation Guide for Telco Racks...
Page 5: Installing A Vnxe3300 Dpe In A Telco Rack
Installing a VNXe3300 DPE in a Telco rack Installing a VNXe3300 DPE in a Telco rack This section describes the components of the VNXe3300 DPE mounting kit. It also describes how to install the mounting kit in a Telco rack and how to install the DPE in the mounting kit.
Page 6: Installing Vnxe3300 Dpe Mounting Trays
Installing a VNXe3300 DPE in a Telco rack Installing VNXe3300 DPE mounting trays This section describes how to install the front and rear DPE mounting trays on the Telco rack. above Note: Be sure to allow enough room to install all the DAEs the DPE.
Page 7: Installing The Vnxe3300 Dpe In The Mounting Trays
Installing a VNXe3300 DPE in a Telco rack Mounting screw (3 per side) CL4812 Figure 5 Securing the 3U DPE rear tray Installing the VNXe3300 DPE in the mounting trays Follow the steps below to install the DPE on the Telco rack: The enclosure is heavy and should be installed into a rack by two people.
Page 8 Installing a VNXe3300 DPE in a Telco rack realizarla siempre dos personas. Para evitar daños personales o en el equipo, el compartimento no debe levantarse ni instalarse en el bastidor sin la ayuda de un elevador mecánico o de otra persona. 1.
Page 9 Installing a VNXe3300 DPE in a Telco rack DPE enclosure Rear fastening bracket (1 per side) CL4814 Figure 7 Securing the back of the VNXe3300 DPE EMC VNXe™3300 System Hardware Installation Guide for Telco Racks...
Page 10: Installing A 3U Dae In A Telco Rack
Installing a 3U DAE in a Telco rack Installing a 3U DAE in a Telco rack This section describes the components of the 3U DAE (DAE6S) mounting kit. It also describes how to install the mounting kit in a Telco rack and how to install the 3U DAE in the mounting kit.
Page 11: Installing 3U Dae Mounting Trays
Installing a 3U DAE in a Telco rack Installing 3U DAE mounting trays This section describes how to install the front and rear DAE trays on the Telco rack. Install the DAE trays: Directly above the DPE ◆ Directly above another DAE ◆...
Page 12 Installing a 3U DAE in a Telco rack Mounting screws (3 per side) rear tray Rear fastening bracket (1 per side) CL3661 Figure 10 Securing the 3U DAE rear tray EMC VNXe™3300 System Hardware Installation Guide for Telco Racks...
Page 13: Installing The 3U Dae In The Mounting Trays
Installing a 3U DAE in a Telco rack Installing the 3U DAE in the mounting trays Follow the steps below to install a DAE enclosure on the Telco rack: The enclosure is heavy and should be installed into a rack by two people. To avoid personal injury and/or damage to the equipment, do not attempt to lift and install the enclosure into a rack without a mechanical lift and/or help from another person.
Page 14 Installing a 3U DAE in a Telco rack Mounting screws (2 per side) CL3664 Figure 11 Securing the 3U DAE front 4. At the back of the enclosure, attach the two rear fastening brackets to the rear corners of the enclosure tray. See Figure 12.
Page 15: Installing A 2U Dae In A Telco Rack
Installing a 2U DAE in a Telco rack Installing a 2U DAE in a Telco rack This section describes the components of the 2U DAE (DAE5S) mounting kit. It also describes how to install the mounting kit in a Telco rack and how to install the 2U DAE in the mounting kit.
Page 16: Installing 2U Dae Mounting Trays
Installing a 2U DAE in a Telco rack Installing 2U DAE mounting trays This section describes how to install the front and rear DAE trays on the Telco rack. Install the DAE trays: Directly above the DPE ◆ Directly above another DAE. ◆...
Page 17 Installing a 2U DAE in a Telco rack CL4817 Figure 15 Securing the 2U DAE rear tray EMC VNXe™3300 System Hardware Installation Guide for Telco Racks...
Page 18: Installing The 2U Dae
Installing a 2U DAE in a Telco rack Installing the 2U DAE Follow the steps below to install a 2U DAE enclosure on the Telco rack. The enclosure is heavy and should be installed into a rack by two people. To avoid personal injury and/or damage to the equipment, do not attempt to lift and install the enclosure into a rack without a mechanical lift and/or help from another person.
Page 19 Installing a 2U DAE in a Telco rack CL4818 Figure 16 Securing the 2U DAE front 4. At the back of the enclosure, attach the two rear fastening brackets to the rear corners of the enclosure tray (Figure 17). Insert one #10-32 x .5 in. screw through each screw hole of the rear fastening bracket and through the rear tray enclosure.
Page 20 Installing a 2U DAE in a Telco rack Copyright © 2011-2012 EMC Corporation. All rights reserved. Published in the USA. Published August, 2012 EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice.