Advertisement
Quick Links
Advertisement
Summary of Contents for Tadano AC 7.450-1
- Page 1 BUILD MANUAL TADANO AC 7.450-1 ALL TERRAIN CRANE...
- Page 2 Tadano AC 7.450-1 Build index Model content Model and parts Tools and pins Assembly Transport mode Operational mode SSL System Product information Contact...
-
Page 3: Main Components
MODEL CONTENT Main components Outrigger Mats Hook Weight Railings Counterweight Counterweight Baseplate Plates Basic crane... - Page 4 Tools & Pins Hex key Plier SSL Winch key Pins bag 1 Pins bag 2 Tweaser Winch key Nuts & Bolts key Pins bag 3 Pins bag 4...
-
Page 5: Transport Mode
The crane has proportional steering, In transport position there but it also includes the counter wise are two options to display the ‘crab-like’ steering option to make Tadano model. manoeuvering on job sites easier. REGULAR STEERING TRANSPORT CONFIGURATION TRANSPORT CONFIGURATION WITH SSL ‘CRAB-LIKE’... -
Page 6: Operational Mode
2. Operational mode OUTRIGGERS 2.2 OUTRIGGER MATS Extend the outriggers outwards. Secure the Put the crane on the outrigger outrigger pads in the middle position (You mats. The mats should be should feel a click) and lower the outriggers by placed with the lifting hooks screwing them down clockwise. - Page 7 LIFTING THE BOOM LADDERS Position the boom upwards in your preferred The ladders can be positioned angle and secure it by fixing both hexagon bolts downwards by prying them up a little, in the boom cylinder with the Hex Key. turning them to the side and folding to the side of the carrier.
- Page 8 2.6 PLACEMENT RAILING 2.8 COUNTERWEIGHTS 2.9 WIND DOWN THE HOOK Place the railings on the uperstructure Place the counterweights Use the winch key to wind down the hook. Push in to and counterweight baseplate. on the baseplate. unwind the winch to keep tension on the rope to prevent the wire from jumping off the sheaves.
- Page 9 2.10 EXTENDING THE BOOM Now carefully pull out the telescopic boom while maintaining tension on the hook ropes. 100% Start with the first boom section, this boom allows for 100% extension, but also has the 45% and 90% extension option build into the 2.10-1 RETRACTING telescopic boom sections.
- Page 10 2.11 SECURING THE ROPE When the sections are set to the prefered height. Connect the rope with the security chain hanging from the end of the boomhead. READY TO START LIFTING! The crane is now build in the normal operational configuration. 2.12 WIND SPEED INDICATOR Pressure fit the wind speed indicator on top of the boom.
- Page 11 3. SSL System PLACEMENT Place the SSL arms on the brackets on both sides of the mainboom with pins from bag 2. PARTS NEEDED The SSL system exists out of 3 pendants and a seperate arm for both sides of the crane. Winch key Short pendants Middle pendants...
- Page 12 3.2 PENDANTS Connect the other two pendants with the nuts and bolts from bag 4. 3.3 CONNECT THE PENDANTS 3.4 REEVE THE SSL SYSTEM Then connect the complete To reeve the SSL system, unwind sufficient rope pendant line to the SSL arm from the SSL winch drum with the the Winch key.
- Page 13 3.5 SECURING THE ROPE Make sure you keep tension on the rope to prevent the rope jumping off the winches. Feed the rope trough the sheeve at the end of the SSL and tie the rope to tie-off point on both sides of the boomhead.
- Page 14 General DIMENSIONS Vehicle dimensions 55'11'' 48'6'' 5'9'' 5'4'' 8'4'' 5'5'' 5'5'' 8'9'' 5'5'' 7'3'' 5'5'' 6'7'' 52'5'' 57'10'' 445/95 R25 / 525/80 R25 385/95 R25...
- Page 15 R 32'4'' (0°) R 32'10'' (15°) R 33'2'' (30°) R 33' (60°) If you have any questions, don’t For service and repairs, contact our hesitate to contact us via: service team via: www.imcmodels.eu www.imcmodels.eu > Service info@imcmodels.eu or email to service@imcmodels.eu facebook.com/imcmodels.eu...
- Page 16 Industrial Merchandising Concepts B.V. HEAD OFFICE Peppelkade 23 3992 AL Houten The Netherlands +31 (0)30 721 0661 info@imcmodels.eu...