Download Print this page

Maretti IP20 Instructions page 3

S-led warm white

Advertisement

S-LED
*
19.8630.92
INSTRUCTIONS
CAUTIONS
Let bij het plaatsen van de ledstrip op de installatietechniek. De ledstrip kan worden gebogen, maar niet vervormd, zoals hieronder weergegeven:
When install the LED strip, please note the installation technique. The LED strip can be bent, but not distorted, as shown below:
2
UIT
OFF
Schakel altijd eerst de stroom uit
De plek voor de LED-strip moet vetvrij,
voordat u installatie-, onderhoud of
droog, vlak en glad zijn voordat u
reparatie-werkzaamheden uitvoert.
de LED-strips aanbrengt.
Always switch off the mains voltage
The place for the LED strip should
before carrying out installation,
be fat-free, dry, flat and smooth
maintenance and repair work.
before applying the LED strips.
7
8
R>=50mm
Buigende diameter
Verwijder het plakband op de
achterkant van de LED-strip tijdens
het vastplakken van de LED-strip
Bending diameter
Remove the adhesive tape on
the back side of the LED strip.
- LED-strips zijn laagspanningsproducten, u moet een voeding (transformator) gebruiken.
- Sluit de ledstrip a.u.b. niet rechtstreeks aan op AC 110V of AC 220V,
anders zullen de ledstrips doorbranden
- LED strips are low voltage products, you must use a power supply (transformer).
- Please do not connect the LED strip directly to the AC 110V or AC 220V,
otherwise it will burn out the LED strips.
"No rights can be derived from the information provided on this Instruction Manual. Information on the Instruction Manual has been compiled with the utmost care and is updated on a continuous basis. Nevertheless Maretti cannot guarantee that all information is free of errors, complete or fully up to date. "
WARM WHITE
3
4
Cutting size, see page 1
Knipafstand, zie pagina 1
LED-strip kan alleen op de stippellijnen
Soldeer draden op soldeer pads (label +/-).
tussen soldeerpads worden geknipt.
De soldeertemperatuur mag niet hoger
zijn dan 350°C voor een maximale duur
van max. 3 seconden.
LED strip can only be cut on
Solder wires on solder pads (label +/-).
the dotted linesbetween solder pads.
The soldering temperature must not
exceed 350°C for a maximum duration
of max. 3 seconds.
9
10
Druk voorzichtig op de LED-strip tussen
LED-strips moeten worden geïnstalleerd op aluminium (of materiaal met vergelijkbare
elektronische componenten.
thermische geleiding) om te voorkomen dat LED's oververhit raken en zorgen voor een
Druk niet op elektronische componenten.
goede warmteafvoer. Meet de TC-temperatuur na 30 min. tijdens gebruik. De TC-temperatuur
mag niet hoger zijn dan 75°C.
Press the LED strip gently between electronic
LED strips must be installed on aluminum (or material with comparable thermal
components to stick it to the surface.
conductivity) to prevent LEDs from overheatingand ensure proper heat dissipation.
Avoid pressing electronic components.
Measure the TC temperatureafter 30 min. during use. The TC temperature
should not exceed 75°C.
5
LED-strips zijn buigbaar.
Max. buigradius is 30mm.
LED strips are bendable.
Max. bending radius is 30mm.
- Reinig het installatieoppervlak, dit zorgt voor de betrouwbaarheid van de lijm.
- Het elektrische aansluitproces moet worden uitgevoerd door een professionele persoon.
- Clean up the installation surface, it will ensure the reliability of the adhesive.
- The electrical connection process must be operated by a professional person.
6
30mm
30mm
LED-strips kunnen niet worden
gebogen of gedraaid in
de gedemonstreerde richtingen.
LED strips can not be bent
or twisted in the demonstrated directions.
11
< 75°C
TC
Houd de LED-strip op de haspel terwijl u
deze op het oppervlak aanbrengt. Verwijder
het plakband en breng de tape aan terwijl
u de haspel tegelijkertijd uitrolt.
Keep the LED strip on the reel while you
apply it to the surface. Remove the adhesive
tape and applythe tape while unrolling
the reel at the same time.
W W W. M A R E T T I . C O M
3/3
3/3

Advertisement

loading