Summary of Contents for Charlton & Jenrick Go Eco Bakechef
Page 1
Clean Air Act Exemption C&J Go Eco Bakechef stoves have been exempted under the Clean Air Act 1993 to burn seasoned wood logs in designated smokeless zones in the UK. This is subject to the correct fitting of the air control plate (the part and fitting instructions are packed separately) maintaining the air wash control at a minimum opening at all times.
PLEASE READ ALL THESE INSTRUCTIONS CAREFULLY! For safety reasons it is essential that your stove is correctly installed and operated. Charlton & Jenrick cannot accept responsibility for any fault or consequential problems arising through incorrect installation or operation. TABLE OF CONTENTS Section Page No 1.
Page 3
7.1.3 Overfiring 7.1.4 Fume Emission 7.1.5 Chimney Fire 7.1.6 CO Alarms 7.2 Warnings 7.3 Clean Air Act (Smoke Control Zones) 7.4 Air controls 7.4.1 Air Control Operation 7.4.2 Air Wash 7.4.3 Tertiary Air 7.4.4 Wood burning Grate 7.4.5 Ashpan 7.5 Cleaning 7.6 Fuels 7.7 Important Notes for Wood Burning 7.7.1 Refuelling on to a low Firebed...
Fig 1: Operating/service Tool Description of Parts Bakechef Stove Assembly Operating/Service Tool Flue Spigot Collar & Fixings Operating Gloves Flame Grill Shelf for Firebox Flat Oven Shelf Profiled Oven Shelf Fig 2 – Go Eco Bakechef Stove Assembly. Bakechef Range Issue 01 06/21...
Page 5
Fig 3 – Go Eco Bakechef Controls for Operation. Air Control (LEFT) “FIRE” Slider. Oven Diverter (Right) Slider. + to increase burn rate – to reduce. + to increase Oven Temp Air is automatically supplied to the – to ignite the fire and reduce Oven fire and fire door glass air wash.
3.0 Preparation of Stove for Installation Your stove comes assembled, checked and packed in a protective plywood crate. Carefully cut and remove the straps and lift off the top and upper crate. Remove any plastic packaging, open the doors and remove all the contents. See List of Components section (above) and check contents carefully.
4.0 Important Safety Information 4.1. WARNINGS AND IMPORTANT SAFETY INFORMATION 4.1.1. READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION! These instructions cover the basic principles to ensure satisfactory installation of the stove, although detail may need slight modification to suit particular local site conditions. In all cases the installation must comply with current local regulations including Building Regulations, Local Authority Byelaws and other specifications or regulations including UK or EU standards referred to as they affect the installation of the stove.
doors and removeable hot plate are provided. Any soot can then be brushed to the bottom of the stove where it can be removed through the large removable oven base access door. 4.1.5. Fuels Only use recommended fuels which is well seasoned or kiln dried wood logs, less than 20% moisture e.g.
stoves providing that the users only burns smokeless fuel or seasoned wood logs with the air limiter fitted in in full accordance with the wood burning instructions. Where the chimney is believed to have previously served an open fire installation, it is possible that the higher flue gas temperature from the stove may loosen deposits that were previously firmly adhered, with the consequent risk of flue blockage.
A suitable 5” 125mm flexible flue liner is permitted be used on these stoves providing that they only burn smokeless fuel or seasoned wood logs with the air limiter fitted in in full accordance with the wood burning instructions. An existing fireplace opening can be bricked up or sealed with a register plate. A short length of suitable quality rigid flue pipe of a minimum 125mm internal diameter may then be used to connect the stove to the chimney.
chamber). Materials above the stove are far more likely to overheat than materials alongside or below. A guideline limiting temperature for solid timber (not surface finishes) is approximately 80- 85 degrees C with a normal ambient room temperature. Temperatures of combustible materials can be substantially lowered with a simple heat shield constructed of a non-combustible material and small air gap (6-12mm for example) between the shield and combustible material.
Page 12
Warn the customer that using excessive air (having the air controls open too wide for too long with a full fuel load) can over-fire and irreparably damage the stove. Damage caused by over firing is NOT covered by any warranty. On completion of the installation and commissioning, check all parts of the appliance are correctly fitted and ensure that the operating instructions and operating tools (including gloves) for the stove are left with the customer.
Manufacturer: Charlton & Jenrick Ltd. Range Designation: Go Eco Bakechef stoves. Models: Go Eco Bakechef stove with nominal output of 5kW. Intended Use: Domestic heating appliances and solid fuel cooking appliances. Independently Performance & Safety tested by: Kiwa Gastec, UKCA NB No: 0558, Kiwa Cermet Italia CE NB No: 0476...
7.0 Operating Instructions Safety Notes for your guidance 7.1. 7.1.1. FIRES CAN BE DANGEROUS – Always use a fireguard to BS 8423:2002 Fireguards for use with solid fuel appliances in the presence of children, the elderly or the infirm. 7.1.2. DO NOT perform modifications to the appliance as this could seriously compromise safety in operation.
(Northern Ireland) 2016. In Wales these are authorised by regulations made by Welsh Ministers. The Go Eco Bakechef stove has been recommended as suitable for use in smoke control areas when burning wood logs. This is conditional upon fitting the supplied secondary air control limiters and following the wood burning instructions precisely.
Air Controls Keep air controls and inlets/outlets clean and free from ash or debris at all times. Keep ventilator air inlet grille or direct external air intake grille (if fitted) clean and clear at all times. Do not leave air controls fully open unless monitoring the fire as over firing damage (typically buckling of components) can result which is not covered by any warranty.
any type of coals or smokeless coal type fuels as it will invalidate warranty, produce unwanted emissions and damage the grate. A large build-up of wood ash is not recommended as it will increase emissions, reduce burning rates and oven temperature noticeably. 7.4.5 Ashpan It is essential that you empty the ash pan regularly to avoid increasing emissions, reducing burning rate and oven temperature.
stove but care must be taken that logs do not touch the baffle or the glass panel. Do not stack logs above the level of the rear firebox liner brick tertiary air holes at the back of the stove. Always make sure that flames are visible above the wood after re-fuelling for cleanest burning. Burning without flames above the fuel will create unnecessary smoke and poor heat output.
Lighting the Stove We recommend that you have two or three small fires before you operate your stove to its maximum heat output. This is to allow the paint to cure steadily and to give a long service life of the paint finish.
Re-fuelling The fire will die down as the fuel is consumed. When the flames begin to disappear, and the remainder is breaking down into glowing embers it is an appropriate time to consider re-fuelling. In normal use, unless the firebox and fire bed has cooled down and it is being revived up to working temperature, then it’s not appropriate to re-fuel when the logs are still flaming fiercely.
To achieve fast boiling or frying on the hot plate, increase the burning rate of the fire accordingly. The hottest part of the plate is the central region towards the front which can achieve temperatures greater than 400-450 deg C. Side edges are slightly cooler which adds flexibility to carrying out cooking and heating activity.
your food without cooking the inside correctly. Adding aromatic wood chips to the fire bed just before cooking can assist to create enhanced smoke flavours. Close the stove door whilst cooking for additional safety and to ensure minimal fume emissions. 7.15 User Maintenance See also the Cleaning section above and Maintenance Guide Section below for further information.
Changing the ceramic glass panel: From time to time the ceramic glass panel or its gasket seals will need to be changed. Note that ONLY ceramic stove glass in the same 4mm thickness can safely be used. This is easiest to accomplish with the door removed from the stove and placed face down on a cushioned surface such as cardboard or a folded dust sheet.
with wet and dry paper will restore the surface to “as new” when required. If the stove will not be used for an extended period of time, then some vegetable oil rubbed on with a paper towel will help resist rusting form any dampness in the atmosphere around the hot plate. 8.13 Cleaning the Flue Ways: This process should be carried out at a minimum annually or more frequently when slow burning or under intensive use.
10.0 Frequently Asked Questions 1 Do stoves require a chimney or a liner? All of our stoves require a suitable chimney or professionally installed flue system. A liner may or may not be required depending on flue conditions and only your installer can confirm. Our stoves do not mandatorily require a liner. 2 How do I clean the chimney? You will require a chimney sweep to clean the chimney.