HermanMiller Locale Modular Electrical Installation And Disassembly

Hide thumbs

page of 10

/ 10
Bookmarks

Quick Links

Download this manual

Parts Included:

BRE04.

Modular Power Duplex

BRE01.

Modular Power Entry

BRE05.

Block-to-Block Jumper

Tools Needed:

#2 Phillips Bit

Power Driver

Locale is among the trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication.

The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.

Locale

Modular Electrical Installation and Disassembly for

™

BRE02.

Modular Power Entry,

New York

NOTICE

All electrical connections to building electrical sources

must be made by a qualified electrician according to

national, state and local electrical codes.

WARNING

Disconnect power before installation. Failure to do so can

cause electrical shock and personal injury.

WARNING

Electrically interconnected units must be mechanically

interconnected.

Recycling Instructions

BRE03.XX04

Power Block

#10-12 x 1/2"

Phillips Pan

Head Tapping

Screw

BRE03.XX08

Power Block Harness

Part no. 1bc57y rev B.

Need help?

Do you have a question about the Locale Modular Electrical and is the answer not in the manual?

Questions and answers

Summary of Contents for HermanMiller Locale Modular Electrical

Page 1 Locale Modular Electrical Installation and Disassembly for ™ Recycling Instructions Parts Included: #10-12 x 1/2” Phillips Pan Head Tapping Screw BRE03.XX04 Power Block BRE04. Modular Power Duplex BRE03.XX08 Power Block Harness BRE01. Modular Power Entry BRE02. Modular Power Entry, New York NOTICE All electrical connections to building electrical sources must be made by a qualified electrician according to...
Page 2 1. Position Power Block (B) or Power Block Harness (C) onto Base Frame. 2. Secure to Frame with Pan Head Screws (D). 3. Locate mounting holes for mounting Modular Power Duplex (A). Part no. 1bc57y rev B. © 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. Locale is among the trademarks of Herman Miller, Inc.
Page 3 4. Secure Modular Power Duplex (A) to inside wall of Base with 4 Pan Head screws (D). 5. Insert end of Modular Power Duplex into Power Block. Make sure connection fully engages. 6. Feed End of Modular Power Entry (E) through opening in side of Base.
Page 4 8. Run end of Power Block (B) through inner wall of Base. 9. Insert end of harness into Power Block. Make sure connection fully engages. 10. When making connections Arrow to Power Block, Make sure reference arrow point Arrow in same direction. Modular Power Entry For New York City: 1.
Page 5 2. Locate mounting holes for mounting Modular Power Entry (F). 3. Secure Modular Power Entry (F) to inside wall of Base with 2 screws supplied with product. Supplied with Product 4. Insert end of Power Block into Block. Make sure connection fully engages.
Page 6 5. After hard wiring J-Box from an outside power source by a qualified electrician, return cover to J-Box. Block-to-Block Jumper: 1. Insert Block-to-Block Jumper (G) through opening in side of Base. 2. Remove Bottom Shelf. Feed Jumper through inner wall of base. Part no.
Page 7 3. Insert end of Jumper into Bottom Port of Power Block. Make sure connection fully engages. 4. Connect Modular Power Duplex to Power Block. Part no. 1bc57y rev B. © 2015 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A. Locale is among the trademarks of Herman Miller, Inc.
Page 8 8 WIRE POWER BLOCK WIRING DIAGRAMS 4-2-2 4 HOTS, 2 NEUTRALS, 2 GROUNDS NOTE: CIRCUITS 1,2,3,4 CORRESPOND TO CIRCUITS (DUPLEX RECEPTACLES) A, B, C, D ALLOWABLE CIRCUIT COMBINATIONS: 1,2,3,4 ; 1,2,3 ,4 ; 1, 2 ,3 ,4 NOTE: CIRCUITS 1, 3, 4 CORRESPOND TO CIRCUITS (DUPLEX RECEPTACLES) A, C, D ALLOWABLE CIRCUIT COMBINATIONS: CIRCUITS 1, 3, 4 ;...
Page 9 10 WIRE POWER BLOCK WIRING DIAGRAMS 4-4-2 4 HOTS, 4 NEUTRALS, 2 GROUNDS ALLOWABLE CIRCUIT COMBINATIONS: 1,2,3,4 ; 1,2,3 ,4 ; 1, 2 ,3 ,4 ; 1,2,3,4,1 ,2 ,3 ,4 ALLOWABLE CIRCUIT COMBINATIONS: CIRCUITS 1,2, 3, 4 ; 1, 2, 3,4 ; OR 1, 2, 3 ,4 Part no.
Page 10 Disassembly and Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non-marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling.