Yellobrik PVD 1800 Quick Start Manual

Module LEDs
The module has several LEDs included to indicate status. Function is
described below:
SDI Present LED
= Valid SDI Signal connected
= (out) Non valid SDI signal or signal missing
REF Status LED
REF Input is bi-level or tri-level analog sync (auto detect), and will cross lock and convert the
SDI output to the REF standard if there is a "mismatch" between the SDI in and REF.
= REF is present and matches the SDI input format
= REF is present but does not match the SDI input format. The SDI
output is being converted to match REF input standard
= (out) REF signal is not present / valid
Power / Status LED
= Power OK, and no internal programmed settings are present
= Power OK, and some internal programmed settings are active*
= Power OK, but the module switch settings have been overwritten
with the yelloGUI application.
(Manual operation of any local switch
will revert module back to the physical switch settings, and will change
LED status back to yellow or green).
= (out) Power not present
* Some additional internal settings have been made using
LED indicates this by turning yellow. The module can be reset to factory default
yelloGUI
using the application, or by using the reset switch on the side of the
module, which can be accessed though a hole with a paper-clip (or similar)
USB Port
The USB port is used for rmware updates and for PC/MAC control using
the yelloGUI software. Download yelloGUI from our website:
www.lynx-technik.com > support > downloads > yelloGUI software
Firmware updates are always provided free of charge and are available
via the yelloGUI.
Fiber I/O Options
The PVD 1800 can accommodate a
variety of ber SDI I/O options which are
detailed below. These are SFP sub
modules and simply plug into the side
of the module. These can be added at
any time.
SDI Fiber Transmitter Options
Model
OH-TX-1-LC / ST / SC
SDI Fiber Receiver Options
Model
OH-RX-1-LC / ST / SC
SDI Fiber Transceiver Options
Model
OH-TR-1
OH-TR-0-850
SDI CWDM Fiber Transmitter Options
Model
OH-TX-4-XXXX
yelloGUI
and the
SDI CWDM Fiber Transceiver Options
Model
OH-TR-4-XXXX
Note: We also have a selection of higher power 80km CWDM ber options
if needed. Please visit our website or contact your LYNX Technik AG sales
representative for more details
Description Power
SFP Fiber TX - Singlemode - LC, ST or SC conn. - 10km -5dBm (1310nm)
Description Sensitivity
SFP Fiber RX - Singlemode - LC, ST or SC connector -18dBm
Description Power
SFP Fiber RX/TX - Singlemode, LC Connector - 10km -5dBm
SFP Fiber RX/TX - Multimode, LC Connector - 300m -5dBm
Description Power
CWDM SFP Fiber TX - Singlemode LC Conn. - 40km -1dBm
XXXX=Wavelength. 18 according to ITU T G692.2
1270nm through 1610nm
Description Power
CWDM SFP Fiber RX/TX - Singlemode LC Conn. - 40km -1dBm
XXXX=Wavelength. 18 according to ITU T G692.2
1270nm through 1610nm
www.lynx-technik.com
yellobrik
PVD 1800
3G SDI Frame Synchronizer
GPI inputs Fiber I/O (option)
Sense
-16dBm
-15dBm
Power and
Sense
Prog. Settings LED
-20dBm
Module Settings
12V Power Input
Delay Adjustment
Module Reset
(through hole under GPI)
Quick
®
Reference
SDI Present SDI Outputs
USB
(
for prog settings and
rmware updates)
REF Status LED
Analog REF IN
SDI Input
WARNING
Class 1 Laser Product