Table of Contents
Advertisement
Quick Links
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2021 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
21e
Advertisement
Table of Contents
Summary of Contents for Franklin 58306
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: Important Safety Information
Harbor Freight Tools for a replacement. Specifications Capacity 2-1/2 Ton (5,000 LB.) Maximum 7-1/2 IN. Fork Height Minimum 3 IN. Fork Length 47-1/2 IN. Fork Width 6-1/4 IN. Width over Forks 27 IN. For technical questions, please call 1-888-866-5797. Page 2 58306... -
Page 3: Set Up Instructions
Adjusting Nut (D615) on the If the Handle does not function underside of the Lever Plate. properly, make adjustments as described in the following chart For technical questions, please call 1-888-866-5797. 58306 Page 3... - Page 4 1. Hold the Control Lever up to its highest position to lower the Forks. 2. Remove the Oil Plug. 3. Pump the Handle up and down several times to push excess air out of the Jack. For technical questions, please call 1-888-866-5797. Page 4 58306...
- Page 5 Control Lever in its highest weight of the load resting as near position to Lower the Forks. as possible to the Steering Wheels. 8. Store in a clean dry place away from children. For technical questions, please call 1-888-866-5797. 58306 Page 5...
-
Page 6: Maintenance
1. Lower Jack completely 3. Replace handle if pin breaks. after every use. 2. Periodically use motor oil or grease to lubricate all moveable parts. For technical questions, please call 1-888-866-5797. Page 6 58306... -
Page 7: Troubleshooting
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175436795 when ordering parts. For technical questions, please call 1-888-866-5797. 58306 Page 7... - Page 8 D611 Screw D604 Elastic Pin D612 Chain D605 Elastic Pin D613 D606 Elastic Pin D614 Adjusting Bolt D607 Elastic Pin D615 Adjusting Nut D608 Control Handle D616 Washer D609 Pull Board For technical questions, please call 1-888-866-5797. Page 8 58306...
- Page 9 D209D Nut (For Type B) D227 Enter Roller D210 D228 D211 Shaft D229 Loading Roller D212 Shaft D230 Roller Shaft D213 Elastic Pin D231 Washer D214 Shaft D232 Washer D215 Roller Frame For technical questions, please call 1-888-866-5797. 58306 Page 9...
-
Page 10: Pump Parts List
Bearing D156 Bushing D123 Elastic Pin D157 Seal Washer D124 Dust Cover D158 Bushing D127 Bearing D159B Sleeve (For Type B) D129 Spring D160B Screw (For Type B) D130 Strike Pin For technical questions, please call 1-888-866-5797. Page 10 58306... -
Page 11: Pump Diagram
Pump Diagram For technical questions, please call 1-888-866-5797. 58306 Page 11... -
Page 12: Limited 90-Day Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
Need help?
Do you have a question about the 58306 and is the answer not in the manual?
Questions and answers
I have a pallet jack of your brand that is new, I haven't used it in a few months and now I'm going to use it for the first time and when you push the handle to raise it, it goes up as the handle returns to its initial position it goes down, I've already put oil on it and sprayed the air on it, what else could it be, I appreciate your help, my job depends on it
The Franklin pallet jack model 58306 could be lowering immediately after raising it due to either of the following reasons:
1. Contaminated oil clogging the valve: The solution is to clean the valve with kerosene and change the oil.
2. Hydraulic component damage: The solution is to replace the damaged part.
This answer is automatically generated