Advertisement
Mounting instruction Protect 2.0 - Neptune 2.0
122212 Rev. E02 - 0220
- This product must only be installed by a licensed installer.
- Dette produktet må kun installeres av en godkjent installatør.
- Denna produkt får endast installeras av auktoriserad installatör.
- Tämän tuotteen asennuksen tulee aina olla sähköalan ammattilaisen tekemä.
www.defa.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for DEFA Bailey lights Protect 2.0
- Page 1 - This product must only be installed by a licensed installer. - Dette produktet må kun installeres av en godkjent installatør. - Denna produkt får endast installeras av auktoriserad installatör. - Tämän tuotteen asennuksen tulee aina olla sähköalan ammattilaisen tekemä. www.defa.com...
- Page 2 Measurements Protect 2.0 Neptune 2.0 - Cross Neptune 2.0 - Half cover Neptune 2.0 - Grid www.defa.com...
- Page 3 Mount & Connect screw fixing IP65 ▲ Ø 4.5-5.0mm www.defa.com...
- Page 4 Close screw fixing 230V 50hz DALI D1 D2 D1 D2 DALI - D1 DALI - D2 www.defa.com...
- Page 5 Twilight sensor manual Protect 2.0 - Neptune 2.0 123187 E01 EN 1119 Norsk versjon Daylight sensor Infrared receiver Daylight threshold Svensk version DIP switch setting (Daylight Threshold) Set the lux level according to the real application disabled environment. Light keeps off if ambient daylight is sufficient (above the threshold preset). 2 lux With insufficient natural light, light will automotically 10 lux turn on. The Daylight Threshold has a 5 min delay. 30 lux Light will never switch off when daylight threshold is set to disable. 50 lux 100 lux 300 lux VIII 500 lux NB! For installation of fittings with Sensor please find additional information in separate Sensor manual on www.defa.com or scan enclosed QR-code. www.defa.com...
- Page 6 The Remote Control controls the Daylight sensor only. The HRC-11 provides a fast and easy way to customize the Daylight sensor. Alter the settings using the functions as described below. The fixture will emit a flash when a new setting has been received. Permanent On/Off function Press “ON/OFF” to select permanent ON or permanent OFF mode. Press “AUTO”, “RESET” to quit this mode. Auto Mode Press “AUTO” to initiate automatic mode. In this mode the sensor and fitting behave according to your selected settings. Reset function Press “RESET”, to restore default settings on the DIP switches. Shift Press "shift" to use secondary button values marked in red. "Shift-mode" is active for 20 seconds. Daylight threshold Press these buttons to set the Lux level to 2Lux/10Lux/50Lux/Disable. The fitting will not activate if the ambient light is above the selected level. If set to Disable, the fitting will always be activated. Ambient daylight threshold l. Press button “Shift”, the red LED is on for indication. 2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold. Note: all other buttons are disabled. www.defa.com...
- Page 7 Protect 2.0 - Neptune 2.0 LightAdjust instruction lumen out Ring Cross Half cover Grid 3000K 4000K 3000K 4000K 3000K 4000K 3000K 4000K LightAdjust - adjustable light Fittings marked with “LightAdjust” are equipped with a setting which makes it possible to set the preferred light level in 8 steps. By delivery the fittings are set on the highest level.
Need help?
Do you have a question about the Bailey lights Protect 2.0 and is the answer not in the manual?
Questions and answers