Table of Contents
Advertisement
Quick Links
Guide to installing thermal night vision camera to vehicle or ATV 4x4
1 CAUTION:
1 The assembling of IR313GT
support. Without the authorization, users can not disassemble or repair.
support. Without the authorization, users can not disassem
2 Please follow the rules and steps in this manual
rules and steps in this manual，or the manufacturer will
afford any legal or economic
economic liability .
3 Without the authorized technician
3 Without the authorized technician's support, please do not change the cables or
fuse of the configuration
4 Please do not put the IR
electric shock, damage or fire
damage or fire by short circuit.
5 Output voltage of IR313GT
other devices not specified.
specified. Please disconnect the IR313GT and the power source
before connection between the IR313GT and the other specified devices.
before connection between the
6 Connect the IR313GT with power source without spe
IR313GT.
7 Photos below are only for reference, please
7 Photos below are only for reference, please subject to products.
2 IR313GT configurations
configurations
1 Standard configuration
tandard configuration
NO.
1
2
NOTE: Bracket and decoding box of Audi
decoding box of Audi are needed
2 Brackets for Audi A6L
NO.
Name
1
A6L Fasten kit
2
M4X10 screw (fasten
3
M4X8 pan-head screw
head screw (fasten the IR313GT)
4
M5X16 pan-head
head tapping screw (fasten the IR313GT)
5
T type cutting kit
6
Cable for IR313GT and decoding box
for IR313GT and decoding box
bling
313GT should be authorized by the factory or local technical
should be authorized by the factory or local technical
location on the car.
IR313GTin moist location or close to water, which will cause
313GT is 12v, it is only for IR output, please do not connect
and the other specified devices.
with power source without specified cables will damage the
Name
IR313GT
Cable
6L
Brackets for Audi A6L
Fasten the IR313GT)
ble or repair.
the manufacturer will not
ge the cables or
, which will cause
output, please do not connect
T and the power source
cified cables will damage the
Quantity
1
1
Quantity
1
3
1
4
1
1
Advertisement
Table of Contents
Summary of Contents for thermal-vision IR313GT
- Page 1 Please disconnect the IR313GT and the power source T and the power source before connection between the before connection between the IR313GT and the other specified devices. and the other specified devices. 6 Connect the IR313GT with power source without spe...
- Page 2 . Membrane switch embrane switch is configured on the panel on the panel lower right to IR313GT is configured the steering wheel steering wheel behind of the grating 3.2 Assemble and route 3.2.1 Disassemble the decoration panel on decoration panel on top of the grating.
- Page 3 3.2.3 Fasten Fix the IR313GT on the bracket the IR313GT on the bracket , please notice that it is the pan head screw it is the pan head screw on the lower left of the bracket. Please fasten the screw the bracket.
- Page 4 Fasten the IR313GT with bracket the IR313GT with bracket behind the grating using 4 M5*15 tapping tapping screws. Preliminarily fasten of the IR313GT 3.2.4 Route Adhesive tape dhesive tape Protection panel Protection panel Disassemble the protection panel and the adhesive tape at the rear of the engine...
- Page 5 To disassemble the screw, the screw, screen cloth of the AC should be removed. of the AC should be removed. Remove the 3 screws on AC air Remove the 3 screws on AC air in vent set at the rear of the engine compartment the rear of the engine compartment with No.10 screw socket.
- Page 6 Please wiring as showing in the pictures and penetrate the cables follow the original as showing in the pictures and penetrate the cables follow the original as showing in the pictures and penetrate the cables follow the original wiring. The cables go into the engine engine compartment through the AC air in vent and the cables e AC air in vent and the cables go out of the engine compartment...
- Page 7 Notice: cables near to the air in vent cables near to the air in vent should be protected with tapes Back of the container...
- Page 8 Cable lead into the cab from this position from this position. 4 Adjustments 1 Connect the IR313GT with BVS and power on 1 Connect the IR313GT with BVS and power on 2 Adjust the pitch angel manually manually. When target, like pedestrian in front of the car 30...
Need help?
Do you have a question about the IR313GT and is the answer not in the manual?
Questions and answers