1. Manuals
  2. Brands
  3. Hamer Manuals
  4. Industrial Equipment
  5. 525WT
  6. Operation manual

Hamer 525WT Operation Manual

Form fill and seal
Hide thumbs
Table of Contents

Advertisement

Quick Links

MODEL 525WT
FORM FILL AND SEAL
OPERATION MANUAL
th
14650 28
Avenue North
Plymouth, MN 55447-4821 USA
TELEPHONE # (763) 231-0100 (800) 927-4674
FAX # (763) 231-0101
WEBSITE: www.Hamerinc.com
MADE
IN THE ***
USA
Rev.7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 525WT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hamer 525WT

Summary of Contents for Hamer 525WT

  • Page 1 MODEL 525WT FORM FILL AND SEAL OPERATION MANUAL 14650 28 Avenue North Plymouth, MN 55447-4821 USA TELEPHONE # (763) 231-0100 (800) 927-4674 FAX # (763) 231-0101 WEBSITE: www.Hamerinc.com MADE IN THE *** Rev.7...
  • Page 3 IMPORTANT Some Machine Assembly drawings are labeled with a range of reference Serial Numbers. Refer to the Serial Number Plate on your machine to relate to the correct Machine Assembly drawing. Those Machine Assembly drawings without reference Serial Numbers should be current to your machine.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS SECTION ONE The Model 525 Wire Tie • Machine Operation....................1 • Machine Specifications..................2 • Machine Layout ....................2 • Film & Bag Specifications................... 3 • Electrical Control Panel..................4 • Operation Controls....................5 • Programmable Controller..................5 Programmable Logic Controller •...
  • Page 6 TABLE OF CONTENTS (CONTINUED) Maintenance Instructions and Schedules..............25 Troubleshooting Guide....................26 Parts Ordering....................... 30 SECTION TWO Model 525 Wire Tie Machine Assembly Drawings • Roll Holder Assembly • Dancer Assembly • Perforator Assembly • Photo Eye Assembly • Vertical Heat Seal Assembly •...

  • Page 7: Section One

    MODEL 525WIRE TIE MACHINE OPERATION The Hamer Model 525 Wire Tie is designed to Form, Fill, and Seal bag sizes of 9” to 16” wide by 16” to 35” long. To activate this machine, product must enter the Volumetric Filler. Product is detected by a sensor in the filler which activates a cam that strikes the prox switch on the filler drum.

  • Page 9: Machine Specifications

    MACHINE SPECIFICATIONS Power 240/120 VAC (3 pole, 4 wire) single phase, 60 Hz 30 Amp (240 VAC – line to line) Requirements (120 VAC = each line to neutral) Requires one air drop: One 1/2” tubing (minimum) with ¼” NPT fitting, Requirements 20 CFM at 80 PSI to the Form Fill &...

  • Page 10: Film & Bag Specifications

    3. TO INSURE THAT YOU HAVE THE PROPER LEVEL OF CONTRAST BETWEEN THE BACKGROUND AND THE EYE MARK, A TEST MUST BE CONDUCTED. IF YOU HAVE ANY DOUBT ABOUT HAVING ENOUGH CONTRAST, SEND SAMPLES TO HAMER LLC. 4. TINTED FILM MUST HAVE CONSISTENT TINT LEVEL - VARIATION CAUSES MISFIRE.

  • Page 11: Electrical Control Panel

    ELECTRICAL CONTROL PANEL FIGURE 1 Rev.7...

  • Page 12: Operation Controls

    OPERATION CONTROLS (Electrical Control Panel) (See Figure 1, pg 9) 1. Low Level Indicator Light - when the light is “on” indicates that the level of product in the Volumetric Hopper is below that of the detector. 2. Main Disconnect - shuts the machine down when the Control Panel is open. The Panel must be closed and the disconnect turned to the “on”...
  • Page 13 THE PROGRAMMABLE CONTROLLER (Viewed through the window on the Electrical Control Panel) The following guide lists the functions for the Programmable Controller as labeled. This will help you understand the Controller and assist you in troubleshooting your machine. Mitsubishi FX1S-30MR-ES/UL PLC When the main power is turned on to the machine, lights on the Controller labeled Power, Ok and Run should be lit.

  • Page 15: Inputs

    INPUTS Light # Function of Light Comments Lights when the Start Button is If the input indicator is on at any other time, the Start Button Start depressed. is faulty. Lights when all Stop Buttons Always use one of the Stop Buttons to stop the machine Stop are pulled out indicating that the operation.

  • Page 16: Outputs

    INPUTS (CONTINUED) Light # Function of Light Comments Light is “ON” when the Side If the Side Seal Temperature is more than 50ºF above or Temperature Seal Temperature is outside of below the setpoint, the Input will be “ON”. The machine Control Alarm it’s operating range.

  • Page 17: Setting Up The Model 525 Wire Tie Machine

    SETTING UP THE MODEL 525 WIRE TIE MACHINE FIGURE 3 INSTALLING A ROLL OF POLYETHYLENE FILM 1. Release the Lock Knob and pull up on the core shaft, removing the core holder from the cardboard tube of the previous roll of film. 2.

  • Page 18: Loading Film Into The Film Feed Belts

    LOADING FILM INTO THE FILM FEED BELTS (See Figure 5) 1. Set the Selector Switch (See Figure 1) to the Hand Position. 2. Feed the film through the Film Feed Rollers. 3. Pass the Film between the Static Eliminator brushes, the Photo Eye Detector and the Perforator Unit. 4.

  • Page 19: Positioning The Vertical Heat Seal

    FIGURE 4 POSITIONING THE VERTICAL HEAT SEAL The centering of the Bag with the Fixed Fill Opening is determined by the position of the Vertical Heat Sealer. • Note: Do not be concerned with location of the label on the bag during this procedure. 1.

  • Page 20: Positioning The Photo Eye Assembly

    POSITIONING THE PHOTO EYE ASSEMBLY The centering of the Label with the Bag is determined by the position of the Photo Eye. 1. Pull back on the Cam Lock to release the Photo Eye Assembly. 2. Compare the center of the Label with the center of the Bag. Measure the distance from the center of the Label to the center of the bag.

  • Page 21: Adjustments

    ADJUSTMENTS AIR PRESSURE REGULATOR/FILTER The Air Pressure Regulator should be set to read 80 PSI. With air connected, pull up on the knob of the regulator. This unlocks the knob so that the air pressure can be adjusted. Once the pressure is set to 80 PSI, push the knob back down to lock knob.

  • Page 22: Teflon Cloth

    TEFLON CLOTH After a period of machine operation, Film residue may build up on the Teflon Cloth of the Vertical Heat Seal Pad. This will cause the Vertical Heat Seal Knife to form the bags improperly. To eliminate the Film residue, lift and turn the Heat Seal Pad Knobs ¼...

  • Page 23: Film Feed Belts ; Removal & Replacement

    FIGURE 5 FILM FEED BELTS REMOVAL AND REPLACEMENT (See Figure 5) CAUTION: TURN THE MAIN DISCONNECT ON THE CONTROL PANEL TO THE "OFF" POSITION AND REMOVE THE AIR SUPPLY FROM THE MACHINE BEFORE MAKING ADJUSTMENTS. 1. Turn the Main Disconnect to the “off” position and remove the Air Supply to the machine. 2.
  • Page 24 7. The film feed belts are ready to be removed from the film feed system and be replaced with the new film feed belts. 8. Install the new Film Feed Belts, first around the independent idler pulley mounted to the tail pulley plate. Next, guide the belt through all the idler pulleys and idler pinch pulleys along the full length of the film path to the take-up pulley on the exit end of the machine.

  • Page 25: Film Roll Brake Cam

    FILM ROLL BRAKE CAM (See Figure 6) The dancer arm and film feed rollers aid in the film unwind process. When the Film Feed Drive System stops, the dancer arm is pulled back to the home position by the dancer spring. In this position, the dancer arm needs to activate the brake air valve.

  • Page 26: Film Feed Chain Tension

    FILM FEED CHAIN TENSION (See Figure 7) The tension on the Film Feed Chain should be checked periodically for proper setting. To Adjust: Loosen the Mounting Bolt beneath the Chain Tensioned with wrenches as shown in (Figure 7). Turn the Chain Tensioned counter- clockwise until the Tensioned Arm is deflected 15 degrees as indicated by the gauge on the Tensioned Body.

  • Page 27: Tear Off Belt Pressure Adjustment

    TEAR OFF BELT PRESSURE ADJUSTMENT (See Figure 8) CAUTION: DISCONNECT POWER BEFORE PERFORMING ADJUSTMENT. To adjust the belt pressure: 1. Slightly loosen the Pinch Idler Pulley 9929. 2. Move the Adjusting Screw in to increase the belt pressure. • Note: Proper adjustment between the Fixed Idler Pulley and the Pinch Idler Pulley should not allow for a .020”...

  • Page 28: Conveyor Adjustments

    CONVEYOR ADJUSTMENTS The Conveyor may be raised or lowered by turning the hand crank. The Conveyor should be adjusted so that it holds the bag in a vertical position as the bag is being filled. The Conveyor must also make enough contact with the bottom of the filled bag to hold it in a vertical position as it is transported by the Feed Belt System The Conveyor must be located horizontally so that the filled bag will fall off the end of the Conveyor Belt just after the bag has been tied.
  • Page 29 FIGURE 9 Rev.7...
  • Page 30 FIGURE 10 FIGURE 11 Rev.7...

  • Page 31: Product Slapper And Wiggler

    PRODUCT SLAPPER AND WIGGLER The purpose of the Product Slapper is to insure that all the product in the product chamber falls into the bag during the fill cycle. During this cycle, the Slapper administers a sharp blow to the product in the chamber, causing it to fall into the bag below.

  • Page 32: Bag Closer Mounting

    BAG CLOSER MOUNTING The Bag Closer can be adjusted in or out as needed to gather bags as they come out of the Film Feed System. 1. Loosen the two Hex Head Cap Screws on the Closer Stop Lock and slide the Bag Closer in or out as needed, then retighten the Hex Head Cap Screws on the Closer Stop Lock.
  • Page 33 MAINTENANCE INSTRUCTIONS AND SCHEDULES 1. Drain the Filter Water Separator Bowl if any water is present. WARNING: DO NOT ALLOW BOWL TO BECOME FULL, CHECK HOURLY. 2. Clean the machine and surrounding area of product buildup. If machine is dusty or dirty, blow off machine with compressed air (Do Not let any dust, dirt, or water get into the Electrical Panel).
  • Page 35 TROUBLESHOOTING GUIDE Refer to the “Programmable Controller” section for additional information. Symptom Cause Correction In the Hand Mode, the Film No power to the Open the Electrical Box: Feed Drive Motor will not Drive Motor. Push the reset lever on the Film Feed Motor engage.
  • Page 36 TROUBLESHOOTING GUIDE (CONTINUED) Symptom Cause Correction The machine stops, but the The Model 125 Bag Determine what is preventing the bags from passing red light does not come on. Closer Limit Switch freely through the Bag Closer. NOTE: The last two bags did not release fast Are the filled bags rubbing the bottom Feed Plates of may be stapled together, or...
  • Page 37 TROUBLESHOOTING GUIDE (CONTINUED) Symptom Cause Correction The side seals are weak. Improper seal Experiment with higher or lower temperatures. Some The side seals are open or temperature. films may require temperatures in excess of 700°F. tear apart easily. Poor sealing surface. Rotate or change the teflon.
  • Page 38 TROUBLESHOOTING GUIDE (CONTINUED) Symptom Cause Correction Volumetric dumps more Sticking or slow clutch air Lubricate, clean, or replace the valve. times then selected on the valve. four position switch. The switch is set on two or Adjust Prox Switch Replace Prox Switch Activating Cam. more dumps.
  • Page 39 PARTS ORDERING When ordering replacement parts, give the part name, part number, model number of the machine and the serial number of the machine. This will help greatly in supplying the correct parts in the least amount of time. MACHINE ASSEMBLY Some Machine Assembly drawings are labeled with a range of reference Serial Numbers.
  • Page 41 SECTION TWO MODEL 525 WIRE TIE ASSEMBLY DRAWINGS Rev.7...
  • Page 45 PART NUMBER Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: DANCER/ANTI-STATIC ASSY, 525WT DECIMALS 2 PL .02 DECIMALS 3 PL .005 ANGLES 1/2 SIZE SCALE DWG NO. REMOVE ALL BURRS 9974...
  • Page 47 PART NUMBER Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: DANCER/ANTI-STATIC ASSY, 525WT DECIMALS 2 PL .02 DECIMALS 3 PL .005 ANGLES 1/2 SIZE SCALE DWG NO. REMOVE ALL BURRS 9974...
  • Page 49 PART NUMBER Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: DANCER/ANTI-STATIC ASSY, 525WT DECIMALS 2 PL .02 DECIMALS 3 PL .005 ANGLES 1/2 SIZE SCALE DWG NO. REMOVE ALL BURRS 9974...
  • Page 51 RUBBER HOLDER ASSEMBLY 3242 AIR CYLINDER 4149 PERFORATOR GUIDE H.S. 10127 EYE SUPPORT EXTENSION ITEM DESCRIPTION QTY. PART NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: FINISH: DECIMALS 2 PL...
  • Page 53 NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: PHOTO EYE ASSEMBLY (525WT) FINISH: DECIMALS 2 PL DECIMALS 3 PL .005 ANGLES SIZE SCALE DWG NO. REMOVE ALL BURRS HEAT TREAT:...
  • Page 55 2718 HHCS, 1/4-20 x 5/8 2584 WASHER, LOCK, 1/4 2523 NYLOCK NUT, 1/4-20 PART ITEM DESCRIPTION NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: PHOTO EYE SUPPORT ASSEMBLY FINISH:...
  • Page 57 3. STAMP PART WITH NUMBER IN POSITION SHOWN. 14551 PHOTO EYE CABLE 14550 PHOTO EYE DETECTOR ITEM QTY. PART NUMBER DESCRIPTION Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: PHOTO EYE DETECTOR W/CABLE...
  • Page 59 HHCS 3/8-16x2.00 SS 2531 NUT,5/16-18 OPTIONAL 2344 FUSE ITEM EXPLODED VIEW/QTY. DESCRIPTION PART NUMBER Hamer LLC SEE BILL OF MATERIAL MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: VERTICAL SIDE SEAL ASSY - HD FINISH: DECIMALS 2 PL .02...
  • Page 61 WHEEL, CARRIAGE 2586 WASHER,LOCK,3/8,SS 2532 NUT, 3/8-16 2137-1 LOCK KNOB ASSEMBLY ITEM DESCRIPTION PART NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: CARRIAGE ASSY,VERT SEAL FINISH: DECIMALS 2 PL .02 DECIMALS 3 PL .005...
  • Page 63 WIRE, 14 GA, BLACK, STRANDED 2340 WRAP, SPIRAL 1/2" DIAMETER 0926 TUBING 1/4" OD POLY FLOW PART ITEM DESCRIPTION NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: KNIFE ASSY, VERTICAL KNIFE...
  • Page 65 NUT,NYLOCK,3/8-16 0635 FITTING, ELBOW, 1/8NPT - 1/4 LINE 0634 1/8 PIPE x1/4" PLASTIC STRAIGHT CONN ITEM EXPLODED VIEW/QTY. DESCRIPTION PART NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: CYLINDER, BEARING, ASSY FINISH: DECIMALS 2 PL .02...
  • Page 67 2607 SHCS, #10-24 x 3/8 2314 STRAIN RELIEF,SMALL 0645E NUT, ELEC. LOCK ITEM EXPLODED VIEW/QTY. PART NUMBER DESCRIPTION Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: Junction Box Assy FINISH:...
  • Page 69 2584 WASHER, LOCK, 1/4,SS 2542 HHCS 1/4-20x1/2 SS 2314 STRAIN RELIEF,SMALL EXPLODED ITEM DESCRIPTION PART NUMBER VIEW/QTY. Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: CONDUIT BOX, ASSEMBLY FINISH: DECIMALS 2 PL DECIMALS 3 PL .005...
  • Page 71 HHCS 3/8-16x.875 SS 2549 HHCS 5/16-18 X 7/8 SS 2543 HHCS 1/4-20 x 3/4 EXPLODED ITEM DESCRIPTION PART NUMBER VIEW/QTY. Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: SLIDE ASSY FINISH: DECIMALS 2 PL .02...
  • Page 73 0931 NIPPLE, 1/8 NPT CLOSE 0634 1/8 PIPE x1/4" PLASTIC STRAIGHT CONN 0633 FLOW CONTROL ITEM PART NUMBER DESCRIPTION Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: GUARD/GUIDE ASSY, VERT SEAL...
  • Page 75 WASHER, 3/8 FLAT, S.S. 2555 HHCS 3/8-16x1 SS 2542 HHCS 1/4-20x1/2 SS 2531 NUT,5/16-18 ITEM DESCRIPTION PART NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: BACKUP ASSY,VERT SEAL FINISH:...
  • Page 81 VOLUMETRIC DRIVE ASSEMBLY (525) 9984 DRIVE ASSY (STANDARD) 1PH 60Hz VOLUMETRIC DRIVE ASSEMBLY (525) 9987 ICE DETECTOR/PROX.SWITCH ASSY 9985 ICE SLAPPER ASSEMBLY 9986-1 WIGGLER ASSEMBLY 9971 VOLUMETRIC MOUNTING ASS'Y, 525WT 9983-50Hz 9983-1 9983-1-50Hz 9983 VOLUMETRIC VOLUMETRIC ASSY VOLUMETRIC ASSY VOLUMETRIC ASSY ITEM DESCRIPTION PART NUMBER ASSY (60Hz)/QTY.
  • Page 83 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: FINISH: DECIMALS 2 PL .02 VOLUMETRIC MOUNTING ASS'Y, 525WT DECIMALS 3 PL .005 ANGLES 1/2 SIZE SCALE DWG NO. REMOVE ALL BURRS HEAT TREAT: 9971...
  • Page 85 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: FINISH: DECIMALS 2 PL .02 VOLUMETRIC MOUNTING ASS'Y, 525WT DECIMALS 3 PL .005 ANGLES 1/2 SIZE SCALE DWG NO. REMOVE ALL BURRS HEAT TREAT: 9971...
  • Page 87 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: FINISH: DECIMALS 2 PL .02 VOLUMETRIC MOUNTING ASS'Y, 525WT DECIMALS 3 PL .005 ANGLES 1/2 SIZE SCALE DWG NO. REMOVE ALL BURRS HEAT TREAT: 9971...
  • Page 91 HHCS,1/4-20 x 3/8 2523 NYLOCK NUT, 1/4-20 Default PART ITEM DESCRIPTION /QTY. NUMBER Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: ICE SLAPPER ASSEMBLY DECIMALS 2 PL .02 DECIMALS 3 PL .005...
  • Page 93 2543 HHCS, 1/4-20 x 3/4 2523 NYLOCK NUT, 1/4-20 Default PART ITEM DESCRIPTION /QTY. NUMBER Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: WIGGLER ASSEMBLY DECIMALS 2 PL DECIMALS 3 PL .005...
  • Page 95 WASHER, LOCK, 1/4 2553 HHCS 3/8-16 X 3/4" 2529 NUT, 1/4 Default ITEM DESCRIPTION PART NUMBER /QTY. Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: FINISH: DECIMALS 2 PL .02 ICE DETECTOR/PROX.SWITCH ASSY...
  • Page 97 2781 WASHER, #10, SS 2595 SHCS #10-24x.5 SS 2583 WASHER, LOCK, #10,SS Default/ ITEM DESCRIPTION PART NUMBER QTY. Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: DECIMALS 2 PL FINISH:...
  • Page 101 0048 PLATE, TAKEUP ADJUSTING 0046 RISER,CONVEYOR TABLE 0040L BELT ITEM PART NUMBER DESCRIPTION Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: CONVEYOR ASSEMBLY (525 WT) KIT DECIMALS 2 PL .02 DECIMALS 3 PL .005...
  • Page 105 2585 WASHER,LOCK, 5/16,SS 2578 WASHER,5/16 2531 NUT,5/16-18 ITEM DESCRIPTION PART NUMBER Hamer LLC UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES AND TOLERANCES ARE MINNEAPOLIS, MINNESOTA FRACTIONS 1/32 TITLE: CONTROL PANEL STANDOFF ASSY DECIMALS 2 PL .02 DECIMALS 3 PL .005...
  • Page 109 HHCS, 1/4-20 x 5/8 2584 WASHER, LOCK, 1/4 0635 FITTING, ELBOW, 1/8NPT - 1/4 LINE 0633 FLOW CONTROL ITEM DESCRIPTION PART NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: FLOW CONTROL ASSEMBLY...
  • Page 111 0909 GAUGE, 1/8 NPT (0-160 PSI) 0908 REGULATOR, 1/8 NPT 0677 FITTING, ELBOW, 1/4NPT - 3/8 LINE ITEM PART NUMBER DESCRIPTION Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: SOLENOID ASSEMBLY...
  • Page 113 2314 STRAIN RELIEF,SMALL 0645E NUT, ELEC. LOCK NOTES: 1. USE TEFLON TAPE ON ALL AIR FITTING THREADS. ITEM DESCRIPTION PART NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: JUNCTION BOX ASSEMBLY...
  • Page 115 SHCS,#8-32 x .5 2584 WASHER, LOCK, 1/4 2582 WASHER,LOCK,#8 Defa PART ITEM ult/Q DESCRIPTION NUMBER Hamer LLC MATERIAL: UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES MINNEAPOLIS, MINNESOTA AND TOLERANCES ARE FRACTIONS 1/32 TITLE: FINISH: DECIMALS 2 PL JOG STOP BOX ASSEMBLY DECIMALS 3 PL .005...
  • Page 117 LIMITED WARRANTY Hamer, LLC warrants that each machine manufactured by us shall be free from defects in material and workmanship for a period of one year from the date of shipment to the original purchaser. Hamer, LLC’s sole obligation under this warranty shall be limited to the repair or...
  • Page 118 -DISCONNECT ELECTRICAL AND AIR POWER BEFORE PERFORMING MAINTENANCE OR REPAIR WORK. -DO NOT OPERATE MACHINE WITH SAFETY GUARDS REMOVED. -MACHINE IS TO BE USED ONLY IN A MANNER OUTLINED IN THE INSTRUCTION MANUAL AND ONLY FOR THE PURPOSE FOR WHICH THE MACHINE WAS DESIGNED. 525WT MAN-4/07 Rev.7...

Table of Contents

Save PDF