Advertisement
Quick Links
Advertisement
Summary of Contents for B-Safe BK061015PRO
- Page 1 BK061015PRO BK061215TRAD ROOFERS KIT USER MANUAL www.bsafe.com.au 1300 783 606...
- Page 2 B-SAFE Back Pack „ 140kg Rated B-SAFE manufacture a range of Roofers Kits with various content options. Each kit has its own unique code number for the content variations. However, this manual still applies to all variations. www.bsafe.com.au 1300 783 606...
- Page 3 USER MANUAL DESCRIPTION B-SAFE Roofers Kit is to provide a fall restraint system for accessing large areas of roof in a safe manner. While still providing the necessary personal protection should unforeseen hazards be encountered. Prior to any work being carried out on a roof or structure, a risk assessment should be conducted to identify the hazards that exist and the risks that they pose.
- Page 4 The BK061215TRAD roofers’ kit is designed for one person use (140kg including tools). The BK061015PRO roofers’ kit is designed for one person use (140kg including tools). No more than one person can be attached to Anchor Points, life lines, rope grabs or lanyards.
- Page 5 Component compatibility. The equipment is designed and tested for use with other B-Safe products, should any other equipment be used on the system, then please consult with the Beaver - B-Safe personnel for approval / compatibility prior to use.
- Page 6 ROOFERS KIT USER MANUAL ANCHORAGES ROOF AND STRUCTURE PROVIDES ANCHORAGE LOCATION BY – Lifting tile and wrapping rafter or top chord of roof truss adjacent to diagonal tie with anchor strap provided. (See right and note the anchor strap should wrap twice). Sling around anchor point, with protection of the sling at sharp edges...
- Page 7 ROOFERS KIT USER MANUAL PLAIN VIEW OF SYSTEM SET UP PLAIN VIEW OF SYSTEM SET UP DANGER Area DANGER Area Rope Safety Line Preferred Anchor Rope Safety Line Safe Point on structure. Ladder Access Preferred Anchor Safe When going over edge Point on structure.
- Page 8 ROOFERS KIT USER MANUAL ACTUAL SYSTEM SET UP PICTURES PROTECTION WHILE CLIMBING OR DESCENDING A LADDER „ A full body harness is used as a best practice with front connection points for the rope grab to be attached with a karabiner „...
- Page 9 ROOFERS KIT USER MANUAL FALL CLEARANCES REFER TO AS/NZS 1891.4, SECTION 7 Ensure that the fully extended lanyard length does not allow the user to reach the edge. Sufficient fall clearance, taking into account the extension of the shock absorbing component of the lanyard has to be included. SHOCK ABSORBING LANYARD „...
-
Page 10: Maintenance
Manufacturer’s label with: „ Serial Number BH01120TRAD „ Model Number (no mesh at rear of harness) „ Date of Manufacture „ Withdrawal from Service Date Check buckles, adjusters and Suspension Trauma Straps “D” Rings BH01120 (BK061015PRO Only) www.bsafe.com.au 1300 783 606... - Page 11 Inspect the lanyard energy absorber for any signs of deployment (Tear web exposed or shrink wrap broken) „ Check lanyard manufacture compliance with AS/NZS1891.5 If any conditions mentioned above are present, check with height safety inspector for further inspection. BL01112PRO-ADJ - Adjustable Lanyard (BK061015PRO Only) Check all stitching Manufacturer’s label with: „ Serial Number „...
-
Page 12: Fall Protection Equipment
ROOFERS KIT USER MANUAL GENERAL MAINTENANCE OF FALL PROTECTION EQUIPMENT „ Any equipment that has been used to arrest a fall should be immediately removed from service and destroyed. Any product involved in a fall arrest load cannot be re-certified due to the high possible loadings that have occurred. „... -
Page 13: Body Harness
Before using the B-Safe harness, you should inspect the harness straps, metal fittings connection points, and labels for damage. Refer to instruction booklet and if in any doubt you should contact your supervisor, supplier or B-Safe for advice. For reference to fall clearance, correct selection, usage and maintenance refer to AS/NZS 1891.4 (selection, use and maintenance). - Page 14 ROOFERS KIT USER MANUAL Roof Access Procedure – Using a ladder Roof Access Procedure – Using a ladder ROOF ACCESS PROCEDURE - USING A LADDER Ladder Bracket procedure Ladder Bracket procedure This product is designed to hold a temporary ladder for entry and exit points onto Ladder Bracket Procedure roofs.
- Page 15 6. Before stepping from the ladder onto the roof structure, ensure you have secu B-Safe Roofers Kit connected your restraint line or shock absorbing lanyard to the first roof anchor p Manufactured for Bunzl Brands & Operations Pty Ltd 55 Sarah Andrews Close, Erskine Park, NSW 2759 7.
-
Page 16: Inspection Certificate
ROOFERS KIT USER MANUAL ROOFERS KIT INSPECTION CERTIFICATE (IN ACCORDANCE WITH AS/NZS 1891.5 & AS/NZS 1891.4) Product: Date of Manufacture: Withdraw from Service Report No: Serial No: Component Condition of fault to be checked Checked Cuts or Tears Abrasion damage especially where there is contact w/ hardware Webbing Excessive stretching Damage due to contact with heat, corrosive or solvents... - Page 17 ROOFERS KIT USER MANUAL ROOFERS KIT INSPECTION CERTIFICATE Product: Date of Manufacture: Withdraw from Service Report No: Serial No: Component Condition of fault to be checked Checked Cuts or Tears Abrasion damage especially where there is contact w/ hardware Webbing Excessive stretching Damage due to contact with heat, corrosive or solvents Deterioration due to rotting, mildew or ultraviolet exposure...
- Page 18 ROOFERS KIT USER MANUAL ROOFERS KIT INSPECTION CERTIFICATE (IN ACCORDANCE WITH AS/NZS 1891.5 & AS/NZS 1891.4) Product: Date of Manufacture: Withdraw from Service Report No: Serial No: Component Condition of fault to be checked Checked Cuts or Tears Abrasion damage especially where there is contact w/ hardware Webbing Excessive stretching Damage due to contact with heat, corrosive or solvents...
- Page 19 ROOFERS KIT USER MANUAL NOTES www.bsafe.com.au 1300 783 606...
- Page 20 ROOFERS KIT USER MANUAL DISTRIBUTED BY: bsafe.com.au Ph: 1300 783 606 02 8882 5700 735-042022...