Table of Contents
Advertisement
Quick Links
Industrial Brush Cutter
(standard flow 16-25 gpm)
(high flow up to 60 gpm)
Operation and Maintenance Manual
Standard Flow Closed Front Starting Serial Number
Standard Flow Open Front Starting Serial Number OFM000952843
High Flow Closed Front Starting Serial Number
High Flow Open Front Starting Serial Number OFM00060130
Part # AU-01-1455
Revision Date: July 2020
Advertisement
Table of Contents
Summary of Contents for Accessories Unlimited AU-01-1455
- Page 1 Operation and Maintenance Manual Standard Flow Closed Front Starting Serial Number Standard Flow Open Front Starting Serial Number OFM000952843 High Flow Closed Front Starting Serial Number High Flow Open Front Starting Serial Number OFM00060130 Part # AU-01-1455 Revision Date: July 2020...
-
Page 2: Table Of Contents
Flywheel Assembly - Parts List C ....................13 Warning Decal Placement – Diagram D ..................14 Warning Decals - Parts List D ....................... 14 Warning Decal Graphics ......................15 TORQUE SPECIFICATION TABLE ..................... 15 General Specification Table ......................15 Accessories Unlimited WARRANTY ..................17... -
Page 3: About This Owner's Manual
ABOUT THIS OWNER’S MANUAL This manual contains information about the usage and maintenance required for the equipment. This document must be available for review by the operator before using the attachment to ensure proper safety, maintenance, and usage. Hazard Notices The following hazard notices are used in this document: NOTE: Notes are used to indicate important information. -
Page 4: About The Brush Cutter Attachment
ABOUT THE BRUSH CUTTER ATTACHMENT The brush cutter attachment is intended for use as a brush cutting and clearing tool. The primary use of the brush cutter attachment includes land clearing, landscaping, and grounds maintenance. Use of this equipment in any other manner is contrary to the intended use of the attachment. -
Page 5: Equipment Inspection Schedule
• Never operate the brush cutter within 200 feet of people, animals, or damageable property. Clear the area of objects that could become projectiles, such as rocks, bottles, and construction debris. • Never operate the brush cutter with the back more than 12” off the ground or where your view is obstructed. •... -
Page 6: Weekly Inspection
Clean debris from the motor area. Check that all guards and safety equipment are in good condition. Weekly Inspection Check blade bolts for correct torque (500 foot/pounds). Check all bolts for tightness. Inspect the deck for cracks, bends, or damage. ... -
Page 7: Safety Chain Placement
Safety Chain Placement AU Industrial Brush Cutter Rev. 7:17 Page 6... -
Page 8: Parts Diagrams And Lists
PARTS DIAGRAMS AND LISTS Brush Cutter - Diagram A Brush Cutter – Parts List A ITEM NO. PART NUMBER DESCRIPTION QTY. 612-2-0020-3 Body, Open Front 612-2-0006-3 Body, Closed Front (Not Shown) 612-2-0005-2 Bearing Housing, Assembled 612-2-0008-2 Wire Protection, Upper 612-2-0012-3 Flywheel Assembly AU Industrial Brush Cutter Rev. - Page 9 Hose Sleeve 612-3-0069 Hose Clamp 612-3-0070 Female Quick Coupler 612-3-0071 Male Quick Coupler 612-3-0110-20 Hub, Standard Flow 612-2-0034 Roller (Optional) AU-01-1455 Cover 612-3-0170 Blade Shipping Retainer (Optional) 612-3-0160 Bearing (Optional) 612-3-0099 Adaptor Fitting AU Industrial Brush Cutter Rev. 7:17 Page 8...
- Page 10 AU Industrial Brush Cutter Rev. 7:17 Page 9...
-
Page 11: Drive Assembly - Diagram B
Drive Assembly - Diagram B AU Industrial Brush Cutter Rev. 7:17 Page 10... -
Page 12: Drive Assembly - Parts List B
Drive Assembly - Parts List B ITEM # PART NUMBER DESCRIPTION QTY. 612-2-0024 Bearing Housing 612-2-0030 3.750 Bearing & Race 612-2-0025 Shaft 612-3-0110 Hub, high Flow 612-3-0060-HF Motor Assembly, High Flow 612-3-0111 Motor Mounting Plate, High Flow 612-3-0111-20 Motor Mounting Plate Standard Flow 612-3-0110-20 Hub, Stannard Flow 612-3-0063-2... - Page 13 HDW-1-2 13 X3.00 HH GR8 1/2-13x3.00 HH GR8 Tap Bolt HDW-1-2 13 Nylock Nut 1/2 Nylock Nut HDW-5-16 24 x2.50 SHCS 5/16 -24 X2 1/2 SHCS HDW-1-2 20 x 1.50 SHCS 1/2-20 X1 1/2 SHCS (High Flow) HDW-1-2 20 x 1.25 SHCS 1/2-20 X 1 1/4 SHCS (standard Flow) HDW-1-2 20 x 1.25 Ferry Cap Screw 1/2-20 X 1 1/4 Ferry Cap Screw (Standard Flow)
-
Page 14: Flywheel Assembly - Diagram C
Flywheel Assembly - Diagram C Flywheel Assembly - Parts List C ITEM # PART NUMBER DESCRIPTION QTY. 612-3-0147 Fly Wheel Plate 612-2-0037 Mulcher Flywheel Optional, (Not Shown) 612-2-0025 Drive Shaft 612-3-0013 Blade 612-2-0007-2 Wire Protection, Lower 612-3-0048 Blade Bolt HDW-LDZ113 1 1/8 Lock Washer HDW-HNGRC 113 12 1 1/8-12 Hex Nut Top Lock... -
Page 15: Warning Decal Placement - Diagram D
HDW-1-2 13 X3.00 GR8 Tap bolt 1/2-13x3.00 HH GR8 Tap Bolt HDW-1-2 13 Rev Lock nut 1/2-13 Rev Lock Nut Warning Decal Placement – Diagram D Warning Decals - Parts List D ITEM # PART NAME DESCRIPTION QTY. Warning Decal Warning Keep Hands and Feet Away Warning Decal DANGER Debris Discharge Area Stay Back 200 Feet... -
Page 16: Warning Decal Graphics
Warning Decal Graphics Decal 1 Decal 2 Decal 3 MODEL NUMB E R SERIAL NUMB E R MADE IN THE USA Decal 4 Decal 5 Decal 6 TORQUE SPECIFICATION TABLE General Specification Table Use the following torques when special torques are not given. Note: These values apply to fasteners as received from supplier, when dry. - Page 17 BOLT SIZES (METRIC) TORQUE MILLIMETERS POUNDS-FOOT NEWTONS-METER AU Industrial Brush Cutter Rev. 7:17 Page 16...
-
Page 18: Accessories Unlimited Warranty
ACCESSORIES UNLIMITED LLC WARRANTY Accessories Unlimited LLC warrants to its authorized dealers who in turn warrant to the original owner, that each new Accessories Unlimited LLC attachment will be free from proven defects in material and workmanship for twelve (12) months after delivery by the authorized Accessories Unlimited LLC dealer to the original buyer. - Page 19 PO BOX 982 Alexandria, MN 56308 1457 Eagle Street Detroit Lakes, MN 56501 Phone: 218-844-8622 www.a-u-llc.com sales@a-u-llc.com AU Industrial Brush Cutter Rev. 7:17 Page 18...