Summary of Contents for BE Hemp Equipment TC-2
- Page 1 TC-2 OPERATIONAL MANUAL TC-2 CYCLONIC TRIM SAVER OPERATIONAL MANUAL BE Hemp Equipment Carson City, Nevada...
- Page 2 TC-2 OPERATIONAL MANUAL Safety At BE Hemp Equipment (BE), safety is our number one priority. The following information provides guidelines for safety when using BE equipment. Any piece of machinery can become dangerous to personnel when improperly operated or poorly maintained. All employees operating and maintaining BE equipment should be familiar with its operation and should be thoroughly trained and instructed on safety.
- Page 3 Never put any foreign objects, other than what the machine is intended for, into the machine’s input ports. Do not operate without first attaching to Trimmer system. The TC-2 is intended to be operated with a 6” trimmer outlet, however smaller can be used with the appropriate adaptors.
-
Page 4: Technical Specifications
TC-2 OPERATIONAL MANUAL TECHNICAL SPECIFICATIONS Wattage: 1500 W Max Amps: 7.8 A Horse Power: 3 HP Speed: 3450 RPM Airflow Capacity: 1400 CFM Cord and Plug: 90” with 6-15P Voltage: 220/230 V Single Phase Freq.: 60 Hz Max Noise: 84dB Inlet Size: 6”... - Page 5 TC-2 OPERATIONAL MANUAL IMPELLER MOTOR, 3HP HOUSING CYCLONIC FUNNEL ASSY CANNISTER FILTER ASSY FRAME ASSY...
-
Page 6: View Window
TC-2 OPERATIONAL MANUAL CIRCUIT BREAKER POWER SWITCH FILTER SCRUBBER HANDLE VOLUTE CLAMP CANNISTER CLAMPS VIEW WINDOW WHEEL LOCKS... - Page 7 TC-2 OPERATIONAL MANUAL REMOVING FROM BOX AND INSPECTING 1. The Trim Saver is not pre-assembled. Transport Trim Saver in its packaging to location before unpacking it. If packing crate or boxes show signs of damage, take pictures and carefully document damage.
- Page 8 TC-2 OPERATIONAL MANUAL ASSEMBLY 1. Assemble Frame Assy. a. Flip Lower Frame Assembly upside down, paying special attention to not damage painted surfaces and install Wheels, Frame (item d) using M6 x 15mm screws and M6 washers. Torque to 12 in-lbs b.
- Page 9 TC-2 OPERATIONAL MANUAL 2. Assemble Canister Assy. a. Remove Inner Drum from Canister Assy, and place Outer Drum on its side. Install Wheels, Canister (item g) onto drum (item o). Hand tighten wheels only. b. Place Outer Drum on its wheels and install Plastic Handle onto drum assy using M8 x 20mm screws, M8 washers, and M8 nuts.
- Page 10 TC-2 OPERATIONAL MANUAL 3. Assembly Cyclonic Funnel and Filter Canister a. Using at least one person to lift the Impeller Housing (item e) onto the Frame Assy, paying special attention to line up mounting holes. Use M8 x 20mm screws and M8 washers to secure b.
- Page 11 TC-2 OPERATIONAL MANUAL 4. Final Assembly a. Fasten Collection Canister to Cyclonic Funnel using two drum lock handles. Note: the two should fit together loosely. b. Secure Kief Bag (item j) to the bottom of the Filter (item h) using the bag clamp (item l).
-
Page 12: Before Operation
Verify hose is securely attached to both Trim Saver and Trimmer using 6” hose clamps. OPERATION The TC-2, Trim Saver is a very simple vacuum which ensures the trim does not touch the impellers during operation. This results in a higher quality trim. Kief and smaller particles will still pass through the impeller chamber and will be collected by the Kief Bag. - Page 13 TC-2 OPERATIONAL MANUAL CLEANING Cleaning of your machine will ensure that your TC-2 can be used for years to come. We suggest a light cleaning daily after each shift and more thorough cleaning every week and/or before being stored. Use standard water based, non-caustic, FDA Food grade approved detergents and/or clean water to clean machine.
-
Page 14: Replacement Parts
TC-2 OPERATIONAL MANUAL REPLACEMENT PARTS BE Hemp is happy to supply parts, however, also want to make the best effort to allow customers to re-supply themselves, as desired with standard consumable parts. If you should need additional support or other parts not on this list, BE Hemp is happy to offer support in whatever fashion needed.